CTC Union IGS-402F?4PH24 Quick Installation Manual

Category
Network switches
Type
Quick Installation Manual
CTCUnionTechnologiesCo.,Ltd.
FarEasternViennaTechnologyCenter
(NeihuTechnologyPark)
8F,No.60ZhouziSt.,NeihuDistrict,Taipei114
Taiwan
T+886226591021
F+886226590237
©2013CTCUnionTechnologiesCo.,Ltd.
Alltrademarksarethepropertyoftheirrespectiveowners.
Technicalinformationinthisdocumentissubjecttochangewithoutnotice.
Introduction
IGS401F/402F/402S4PH24modelsarenonmanagedindustrial
grade Gigabit PoE (Power over Ethernet) switches that provide
stable and reliable Ethernet transmission. Housed in rugged DIN
railorwallmountableenclosures,theseswitchesaredesignedfor
harshenvironments,suchasindustrialnetworkingandintelligent
transportation systems (ITS) and are also suitable for many
military and utility market applications where environmental
conditions exceed commercial product specifications. Standard
operating temperature range models (0 to 60°C) and wide
operating temperature range models (40 to 75°C) fulfill the
specialneedsofindustrialautomationapplications.
Features
RedundantdualDCinputs24/48VDC
DCPower"boost"feature
IP30ruggedmetalhousing
Widetemperaturerange‐40~75C(Emodels)
SupportforEthernetjumboframes
DIPswitchenable/disablebroadcaststormfilter
UL508,CE,FCC,EN501214Railtraffic
IndustrialgradeEN6100062EMSandEN6100064EMI
Specifications
EthernetInterface
Connector:RJ45(shielded)
4PoEenabledports,AlternateAMode
AutoMDI/MDIX
Speed:10/100/1000BaseT(Auto)
Duplex:Full/Half(AutonegotiationperIEEE802.3u)
SupportsIEEE802.3xFlowControl
Store&ForwardSwitchingFabric:12Gbpsnonblocking
Packetbuffer:1mb
Standards:IEEE802.3,802.3u,802.3x,802.3ab,802.3z
802.3af(15.4WPoE),802.3at(30WPoE,120Wtotal)
8KMACtable
MTU:64~10240bytes
BroadcastStormprotection(enable/disablebyDIP)
Positive(VCC+)pins1,2(55VDC±1V)
Negative(VCC)pins3,6
QuickInstallationGuide
IGS401F4PH24,402F4PH24,IGS402S4PH24
IGS401F4PHE24,402F4PHE24,IGS402S4PHE24
IndustrialGradeGigabitPoESwitches
TodownloadthisQIGoramorecompleteusermanual,pleasevisit
http://www.ctcu.com/Industrial/
Specifications(cont.)
OpticalEthernetInterface
1000BaseX,1port(401),2ports(402)
FixedSCconnectors(401Fand402Fmodels)
PluggableSFPx2(402Smodel)
Multimode(2km)50/125um,62.5/125um
Singlemode(30or50km)9/125um
Wavelength:1310nm(S/MorM/M)
Power
Absoluterange:20~57VDC
Reversepolarityprotection:Yes
Dualpowerinputs:Yes
Connector:removableterminalblock
Consumption:2.89A@48VDC,138.2Watts(120WforPoE)
5.97A@24VDC,143.2Watts(120WforPoE)
Mechanical
Water&DustProof:IP30Protection
Dimensions:106x62.5x135mm(DxWxH)
Mounting:DINRail,WallMount(kitsincluded)
Weight:approximately850g
Environmental
OperatingTemperature:
0°C~60°C,‐40°C~75°C(widetemp.for*E)
StorageTemperature:‐40°C~85°C
Humidity:5~95%(noncondensing)
Certifications
EMI:FCCPart15subBclassA,EN55022ClassA,EN6100064
EMS:(ElectromagneticSusceptibility)
EN6100062ImmunityforIndustrialEn vironment
EN6100042(ESD)Level3,CriteriaB
EN6100043(RS)Level3,CriteriaA
EN6100044(Burst)Level3,CriteriaA
EN6100045(Surge)Level3,CriteriaB
EN6100046(CS)Level3,CriteriaA
EN6100048(MagneticField)Level3,CriteriaA
Safety:UL508(pending)
RailwayTraffic:EN501214
Shock:EN60068227Freefall:EN60068232
Vibration:EN6006826
MTBF:316408hr(401F),306704hr(402F).334448hr(402S)
[email protected] www.ctcu.com
V1.0
Connectors LEDIndicators
IGS401F/402F/402S4PH24 have LEDs on the front face that
reporttheconditionofpower,fault, PoE,Fiberlink, LANlink and
speed.
PWR
1
PWR 2 Fault
Fiber 1
Fiber 2
LINK/
ACT
100/
1000
LINK/
ACT
100/
1000
PWR1: This green LED will light if power isconnected and active
atthePWR1terminalconnection.
PWR2: This green LED will light if power is connected and active
atthePWR2terminalconnection.
Fault: This amber LED will light if one of the power inputs has
faultconditionandaslongasDIPsw#1isOFF.
Fiber 1: This green LED will light when the fiber 1 port has an
opticallinkandwillflashwhenthereisEthernettraffic.
IGS402F4PH24 IGS402S4PH24
Both models have four electrical 10/100/1000M Auto
Negotiation and Auto MDI/MDIX Ethernet LAN ports (labeled 1
thru 4) that utilize shielded RJ45 connectors and support PoE
(Power over Ethernet) per IEEE802.3af (15.4W) or IEEE802.3at
(30W)forconnection tostandardPoE PD(Power Device)suchas
IPCameras,AccessPoints,IPPhones,DigitalSignage,etc.
Fiber 2: This green LED will light when the fiber 2 port has an
opticallinkandwillflashwhenthereisEthernettraffic.
100/1000: This dual color LED will light with amber color when
the LAN connected speed is 1000M, it will light with green color
whentheLANspeedis100Mandwillremainoffiftheconnected
speedis10M.
IGS402F4PH24gigabitopticalports(Fiber1/Fiber2)usefixed
transceivers with SC or ST optical connect ions for multimode or
single mode fiber depe nding on model. (IGS401F4PH24 model
has only one fiber port.) IGS402S4PH24 model provides SFP
cagesandsupportsdualrate,125Mbpsor1.25GbpsSFPmodules,
inserted into Fiber 1 and Fiber 2 ports. Dual rate support allows
use of specific SFP modulesfor fiber connection to other gigabit
Ethernet(1000BaseX)equipmentortolegacyFastEthernetfiber
(100BaseFX).
LINK/ACT: This green LED will light when theLAN porthas a link
andwillflashwhenthereisEthernettraffic.
PoE: These green LEDs will light when the LAN has successfully
negotiated PoE and is supplying output power to the remote
connectedPDdevice.
Installation
Power,AlarmandDIPswitch
IGS401F4PH24/402F(S)4PH24 comes with both wall mount
and DIN rail hardware brackets. When installing the DIN rail
bracket,besuretocorrectlyaligntheorientationpin.
A removable terminal block provides both power and alarm
connections.Powercanbeprovidedthroughthedualinputsfrom
separatesources.Oneelectrical relaycanbewiredintoanalarm
circuit.TherelayisconnectedasNormallyClosed(willopenupon
alarmcondition).
DINRailWallMount
IGS401F/402F(S)4PH24withDINRailbrackethasasteelspring
in the upper rail of the bracket. This spring is compressed for
mountingandunmountingbyapplyingdownwardforce.
IGS401F/402Fusesa2poleDIPswitchforconfiguration,while
theIGS402Susesa4poleDIPswitchforconfiguration.Eachpole
oftheswitchhasthefollowingfunctions:
1. Alarm Enable: When 'On' this switch will disable alarm relay
and fault LED if there is a power failure in one supply. If only
connecting to a single power source, place this switch 'On' to
disablealarm.
2. BSP: When 'On' this switch will disable the broadcast storm
protectionfeaturewhichisenabledbydefault.
3. Fiber 2 : This dual rate fiber port (IGS402S4PH24 ONLY)
supports optical Ethernetrate of 100M or 1G, depending on the
setting and the inser ted SFP module. When set to 'On', the port
supports Fast Ethernet rate and should use an SFP rated for
125~155Mbps. When set 'Off', the port is configured for gigabit
Ethernetandrequiresa1.25gbpsSFPmodule.
mountingunmounting
4.Fiber1:ThesamesettingsasforFiber2port.
[email protected] www.ctcu.com
  • Page 1 1
  • Page 2 2

CTC Union IGS-402F?4PH24 Quick Installation Manual

Category
Network switches
Type
Quick Installation Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI