CTC Union IGS?401F?4PHE24 Quick Installation Manual

Brand: CTC Union

Model: IGS?401F?4PHE24

Category: Network switches

Type: Quick Installation Manual

This manual is also suitable for



CTCUnionTechnologiesCo.,Ltd.

FarEasternViennaTechnologyCenter

(NeihuTechnologyPark)

8F,No.60ZhouziSt.,NeihuDistrict,Taipei114

Taiwan



T+886‐2‐26591021

F+886‐2‐26590237

E[email protected]



Alltrademarksarethepropertyoftheirrespectiveowners.

Technicalinformationinthisdocumentissubjecttochangewithoutnotice.



Introduction

IGS‐401F/402F/402S‐4PH24modelsarenon‐managedindustrial

grade Gigabit PoE (Power over Ethernet) switches that provide

stable and reliable Ethernet transmission. Housed in rugged DIN

railorwallmountableenclosures,theseswitchesaredesignedfor 

harshenvironments,suchasindustrialnetworkingandintelligent

transportation systems (ITS) and are also suitable for many

military and utility market applications where environmental

conditions exceed commercial product specifications. Standard

operating temperature range models (0 to 60°C) and wide

operating temperature range models (‐40 to 75°C) fulfill the

specialneedsofindustrialautomationapplications.



Features

• RedundantdualDCinputs24/48VDC

• DCPower"boost"feature

• IP30ruggedmetalhousing

• Widetemperaturerange‐40~75C(‐Emodels)

• SupportforEthernetjumboframes

• DIPswitchenable/disablebroadcaststormfilter

• UL508,CE,FCC,EN50121‐4Railtraffic

• IndustrialgradeEN61000‐6‐2EMSandEN61000‐6‐4EMI



Specifications

EthernetInterface

• Connector:RJ‐45(shielded)

• 4PoEenabledports,AlternateAMode

• AutoMDI/MDI‐X

• Speed:10/100/1000Base‐T(Auto)

• Duplex:Full/Half(Auto‐negotiationperIEEE802.3u)

• SupportsIEEE802.3xFlowControl

• Store&ForwardSwitchingFabric:12Gbpsnon‐blocking

• Packetbuffer:1mb

• Standards:IEEE802.3,802.3u,802.3x,802.3ab,802.3z

802.3af(15.4WPoE),802.3at(30WPoE,120Wtotal)

• 8KMACtable

• MTU:64~10240bytes

• BroadcastStormprotection(enable/disablebyDIP)

• Positive(VCC+)pins1,2(55VDC±1V)

• Negative(VCC‐)pins3,6



QuickInstallationGuide



IGS‐401F‐4PH24,402F‐4PH24,IGS‐402S‐4PH24

IGS‐401F‐4PHE24,402F‐4PHE24,IGS‐402S‐4PHE24

IndustrialGradeGigabitPoESwitches



TodownloadthisQIGoramorecompleteusermanual,pleasevisit

http://www.ctcu.com/Industrial/



[email protected]



Specifications(cont.)

OpticalEthernetInterface

• 1000Base‐X,1‐port(401),2‐ports(402)

• FixedSCconnectors(401Fand402Fmodels)

• PluggableSFPx2(402Smodel)

• Multimode(2km)50/125um,62.5/125um

• Singlemode(30or50km)9/125um

• Wavelength:1310nm(S/MorM/M)

Power

• Absoluterange:20~57VDC

• Reversepolarityprotection:Yes

• Dualpowerinputs:Yes

• Connector:removableterminalblock

• Consumption:2.89A@48VDC,138.2Watts(120WforPoE)

5.97A@24VDC,143.2Watts(120WforPoE)

Mechanical

• Water&DustProof:IP30Protection

• Dimensions:106x62.5x135mm(DxWxH)

• Mounting:DIN‐Rail,WallMount(kitsincluded)

• Weight:approximately850g



Environmental

• OperatingTemperature:

• 0°C~60°C,‐40°C~75°C(widetemp.for*‐E)

• StorageTemperature:‐40°C~85°C

• Humidity:5~95%(non‐condensing)



Certifications

• EMI:FCCPart15subBclassA,EN55022ClassA,EN61000‐6‐4

• EMS:(ElectromagneticSusceptibility)

• EN61000‐6‐2ImmunityforIndustrialEn vironment

• EN61000‐4‐2(ESD)Level3,CriteriaB

• EN61000‐4‐3(RS)Level3,CriteriaA

• EN61000‐4‐4(Burst)Level3,CriteriaA

• EN61000‐4‐5(Surge)Level3,CriteriaB

• EN61000‐4‐6(CS)Level3,CriteriaA

• EN61000‐4‐8(MagneticField)Level3,CriteriaA

• Safety:UL508(pending)

• RailwayTraffic:EN50121‐4

• Shock:EN60068‐2‐27Freefall:EN60068‐2‐32

• Vibration:EN60068‐2‐6

• MTBF:316408hr(401F),306704hr(402F).334448hr(402S)

[email protected] www.ctcu.com

V1.0

 

Connectors LEDIndicators

 IGS‐401F/402F/402S‐4PH24 have LEDs on the front face that

reporttheconditionofpower,fault, PoE,Fiberlink,  LANlink and

speed.



 

PWR

PWR 2 Fault

Fiber 1

Fiber 2

LINK/

ACT

100/

1000

LINK/

ACT

100/

1000

 

 PWR1: This green LED will light if power isconnected and active

atthePWR1terminalconnection.

 

PWR2: This green LED will light if power is connected and active

atthePWR2terminalconnection.





Fault: This amber LED will light if one of the power inputs has

faultconditionandaslongasDIPsw#1isOFF.





Fiber 1: This green LED will light when the fiber 1  port has an

opticallinkandwillflashwhenthereisEthernettraffic.

IGS‐402F‐4PH24 IGS‐402S‐4PH24



Both models have four electrical 10/100/1000M Auto

Negotiation and Auto MDI/MDI‐X Ethernet LAN ports (labeled 1

thru 4) that utilize shielded RJ‐45 connectors and support PoE 

(Power over Ethernet) per IEEE802.3af (15.4W) or IEEE802.3at 

(30W)forconnection tostandardPoE PD(Power Device)suchas

IPCameras,AccessPoints,IPPhones,DigitalSignage,etc.

Fiber 2: This green LED will light when the fiber 2  port has an

opticallinkandwillflashwhenthereisEthernettraffic.



100/1000: This dual color LED will light with amber color when

the LAN connected speed is 1000M, it will light with green color

whentheLANspeedis100Mandwillremainoffiftheconnected

speedis10M.



IGS‐402F‐4PH24gigabitopticalports(Fiber1/Fiber2)usefixed

transceivers with SC or ST optical connect ions for multimode or

single mode fiber  depe nding on model. (IGS‐401F‐4PH24 model

has only  one fiber port.) IGS‐402S‐4PH24 model provides SFP

cagesandsupportsdualrate,125Mbpsor1.25GbpsSFPmodules,

inserted into Fiber 1 and Fiber 2 ports. Dual rate support allows

use of specific SFP modulesfor fiber connection to other gigabit

Ethernet(1000Base‐X)equipmentortolegacyFastEthernetfiber

(100Base‐FX).



LINK/ACT: This green LED will light when theLAN porthas a link

andwillflashwhenthereisEthernettraffic.



PoE: These green LEDs will light when the LAN has successfully

negotiated PoE and is supplying output power to the remote

connectedPDdevice.



 

Installation

Power,AlarmandDIPswitch

IGS‐401F‐4PH24/402F(S)‐4PH24 comes with both wall mount

and DIN rail hardware brackets. When installing the DIN rail

bracket,besuretocorrectlyaligntheorientationpin.





A removable terminal block provides  both power and alarm

connections.Powercanbeprovidedthroughthedualinputsfrom

separatesources.Oneelectrical relaycanbewiredintoanalarm

circuit.TherelayisconnectedasNormallyClosed(willopenupon

alarmcondition).



 

 DINRailWallMount

 

 IGS‐401F/402F(S)‐4PH24withDINRailbrackethasasteelspring

in the upper rail of the bracket. This spring is compressed for

mountingandun‐mountingbyapplyingdownwardforce.



IGS‐401F/402Fusesa2‐poleDIPswitchforconfiguration,while

theIGS‐402Susesa4‐poleDIPswitchforconfiguration.Eachpole

oftheswitchhasthefollowingfunctions:





1. Alarm Enable: When 'On' this switch will disable alarm relay 

and fault LED if there is  a power failure in one supply. If only

connecting to a  single power source, place this switch 'On' to

disablealarm.



 

2. BSP: When 'On' this switch will disable the broadcast storm

protectionfeaturewhichisenabledbydefault.



 

3. Fiber 2 : This dual rate fiber port (IGS‐402S‐4PH24 ONLY)

supports optical Ethernetrate of 100M or 1G, depending on the

setting and the inser ted SFP module. When set to 'On', the port

supports Fast Ethernet rate and should use an SFP rated for

125~155Mbps. When set 'Off', the port is configured for gigabit

Ethernetandrequiresa1.25gbpsSFPmodule.



 mountingun‐mounting

4.Fiber1:ThesamesettingsasforFiber2port.

[email protected] www.ctcu.com

CTC Union IGS?401F?4PHE24 Quick Installation Manual

Brand: CTC Union

Model: IGS?401F?4PHE24

Category: Network switches

Type: Quick Installation Manual

This manual is also suitable for

Download PDF

report

CTC Union IGS?401F?4PHE24 Quick Installation Manual

This manual is also suitable for

CTC Union IGS?401F?4PHE24 Quick Installation Manual

Related papers

Other documents