Kogan KAMN32F7SA User guide

32” FULL HD IPS 75HZ FREESYNC

MONITOR

1920 x 1080

KAMN32F7SA

Ensure to read all instructions and warnings in this user guide prior to assembly and use.

Retain this user guide for future reference.

• Ensure the monitor is unplugged before cleaning.

• This monitor is designed with ventilation holes on the back of the casing. Do not cover

or block them.

• Do not insert any object or spray anything into the vents.

• Do not place the monitor near heaters, stoves, fireplaces, or other heat sources.

• Do not place the monitor in rooms lacking adequate ventilation.

• Do not position the monitor on unstable surfaces or unsafe locations. If the monitor

falls, it may be damaged and injure people around its vicinity.

• Unplug the monitor if it will not be used for an extended period.

• Do not place heavy objects on the monitor, its power cord, or any connected cable.

• Do not open the back panel of the monitor as it contains a high-voltage current even

when not plugged in.

The terms HDMI and HDMI High-Definition Multimedia

Interface and the HDMI Logos are trademarks or registered

trademarks of HDMI Licensing Administrator, Inc. in the

United States and other countries.

SAFETY & WARNINGS

A Monitor (x1)

B Stand connector (x1)

C Stand base (x1)

D 10mm M4 stand base screw (x5)

E 10mm M4 VESA

screw (x4)

F Cover (x1)

G HDMI cable (x1)

H Power cable (x1)

I User guide (x1)

COMPONENTS

Front view

1 Menu button Press to display the OSD menu or enter sub-menus.

2 Down button Press to move down in the menu.

3 Up button Press to move up in the menu.

4 Exit button Press to exit.

5 Power button Press to turn the monitor ON/OFF.

OVERVIEW

Back view

6 Audio output port

7 VGA port

8 HDMI port

9 Power port

1. Open the packaging and remove the stand connector (B) and stand base (C). Using

a Phillips head screwdriver (not supplied), secure the stand connector (B) to the stand

base (C) with two 10mm M4 stand base screws (D).

2. Remove the upper foam and reveal the lower part of the monitor (A). Fix the monitor

(A) to the stand connector (B) with three 10mm M4 stand base screws (D) in the

marked grey holes as illustrated.

3. Place the cover (F) over the stand connector (B).

STAND ASSEMBLY

B

Attention:

The monitor is fragile. Keep the foam underneath the monitor while

assembling the stand.

D

C

D

F

A

B

1. Open the packaging and take out the monitor (A) with the foam attached. Gently

place it on a desktop or table.

2. Remove the stand connector (B), stand base (C), and foam covering the back of the

monitor (A). Press the release button to remove the stand plate.

If the monitor was already attached to the stand, remove the stand.

3. Mount the monitor (A) as desired with the steps provided with your VESA mount.

Stand plate

Mount (not

included)

VESA MOUNT

Notes:

• The mounting hole distance for this monitor is 75 x 75mm.

• VESA mount and mounting accessories are not included.

B

C

A

Release

button

Power cable

Connect one end of the power cable into the power

port on the monitor. Connect the other end into a

power socket.

Earphones (audio out)

Earphones and other audio devices (not included) can

be connected to the audio output port on the monitor.

The monitor may need to be set as the PC’s default

sound output device.

HDMI

Connect the HDMI cable into your input device’s

display output and the monitor’s HDMI port.

VGA

Connect a VGA cable (not included) into your input

device’s display output and the monitor’s VGA port.

Power cable

Earphones

(Not included)

VGA cable

(not included)

VGA OUTPUT

(PC)

CONNECTIVITY

HDMI cable

1. Connect the monitor to the input device via HDMI or VGA.

2. Connect one end of the power cable to the monitor, then connect the other end

directly to a power socket. Turn on the power socket.

3. Press the power button to turn the monitor on.

4. When finished use, press the power button again to turn it off.

FreeSync

• To use this feature, ensure your hardware has FreeSync capabilities and the graphics

drivers are fully up to date.

• After connecting, you may receive a prompt to enable the feature on your computer. If

you do not receive the prompt, you may need to enable the function in your graphics

card menu.

• See your graphics card manufacturer’s documentation for instructions on how to turn

on and/or enable FreeSync.

On-screen display (OSD) menu

The OSD menu may be used to adjust the monitor’s settings.

Note:

When using the monitor for the first time, the monitor will configure to optimal settings

automatically.

OPERATION

1. Press the menu button to enter the OSD menu.

2. Press up and down buttons to browse the settings categories. With the desired

category highlighted, press the menu button to enter the sub-menu.

3. Press the up and down buttons to browse the sub-menu. With the desired sub-menu

setting highlighted, press the menu button to select the sub-menu setting.

4. Press the up and down buttons to adjust the setting. Once adjusted, press the menu

button to confirm.

5. Press the exit button to return to the display.

OSD menu options

Below is a list of settings that can be adjusted in the OSD menu.

Category Sub-menu Setting Description

Brightness

Brightness 0–100 Adjusts the display brightness

Contrast 0–100 Adjusts the display contrast

Backlight 0–100 Adjusts the display backlight

Low blue ON/OFF Enables/disables the blue light

reduction function

ECO

STANDARD/

TEXT/GAME/

MOVIE/FPS/RTS

Sets the display’s colour balance to

pre-set levels calibrated for different

uses.

DCR ON/OFF Enables/disables the dynamic

contrast ratio function

Image

Horizontal

position 0–100 Adjusts the horizontal position of the

video display area (VGA only)

Vertical

position 0–100 Adjusts the vertical position of the

video display area (VGA only)

Clock 0–100 Adjusts the display clock setting

Phase 0–100 Adjusts the display phase setting

Aspect Wide (16:9), 4:3 Adjusts the aspect ratio

FreeSync ON/OFF Turns the FreeSync function on/off

Colour

Warm mode Red/green/blue Adjusts the red/green/blue levels

Cool mode Red/green/blue Adjusts the red/green/blue levels

User mode Red/green/blue Adjusts the red/green/blue levels

HDR mode On/Off Turns the HDR mode on/off.

OSD Setting

Language

English, 简体中文,

한국어, Русский,

Español, Deutsch,

Italiano, Français,

Portugues, Turkce,

Polski, Nederlands

Sets the OSD language

OSD

H-position 0–100 Adjusts the horizontal position of the

OSD menu

OSD

V-position 0–100 Adjusts the vertical position of the

OSD menu

OSD

transparency 0–100 Adjusts the transparency of the

OSD menu

OSD time out 5–60

Sets how long the OSD menu will

remain on-screen after no input

(seconds)

Reset

Image N/A Restores the display to VGA image

defaults

Colour N/A Automatically configures the VGA

colour settings

Reset N/A Restores the monitor to factory

default settings

Timecount 10–90 mins Adjusts how long the time count

function should be set for

Misc Signal source VGA/HDMI Adjusts the input source

ECO modes

There are various pre-set colour modes suited for various use cases available on this monitor.

These can be accessed using the ECO modes menu. The modes include the following:

• Standard (suitable for most activities)

• Text (best suited when reading text)

• Game (best suited for general gaming)

• Movie (best suited when watching movies)

• FPS (best suited when playing first-person shooter games)

• RTS (best suited when playing real-time strategy games)

GamePlus menu

To access the GamePlus menu, press the exit button, followed by the menu button.

The GamePlus menu allows users to access two settings:

• Crosshair – Allows users to change the appearance of the crosshair used when

gaming)

• Timecount – Allows users to turn on a timer to record how long the monitor has been

used (10–90mins).

• To clean the screen, turn it off, unplug it, and wait for it to cool completely. Wipe it with

a dry micro-fibre cloth.

• To clean the body, wipe with a clean, slightly dampened cloth.

Screen size 32”

Aspect ratio 16:9

Brightness 300cd/m² (typical)

Panel IPS

Resolution 1920 x 1080

Refresh rate 75Hz

Response time 8ms

Viewing angle ≥178°(H)/178°(V)

Contrast ratio 1000:1

VESA mounting 75 x 75mm

Colours 16.7M

Signal input HDMI 1.4 x1, VGA x1

Power supported 100–240V, 50/60Hz, 1.1A

SPECIFICATIONS

CLEANING & CARE

Note:

Do not use cleaning alcohol, ammonia-based liquids, or other harsh cleaners.

Audio

Speakers No

Accessories

Power cable Yes

HDMI cable Yes

Additional functions

Low blue light Yes

Flicker-free Yes

Physical dimensions

Dimensions (w. stand) 720.5 x 84.6 x 507.0mm

Dimensions (without stand) 720.5 x 42.9 x 423.1mm

Net weight 6.3kg

Gross weight 8.2kg

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com

Kogan KAMN32F7SA User guide

Related papers

Other documents