CYP PUV-44XPL-4K22-KIT User manual

PUV-44XPL-4K22-KIT

4 x 4 HDMI HDBaseT™ LITE Matrix with 2x Independent

HDMI outputs & Audio De-embedding (4K, HDCP2.2,

PoH, 60m) inc. 4x PUV-1210PL-RX Receivers

OPERATION MANUAL

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

RDV1 05/08/16 First release

CONTENTS

1. Introduction ................................................................................... 1

2. Applications .................................................................................. 1

3. Package Contents ....................................................................... 2

4. System Requirements ................................................................... 2

5. Features ......................................................................................... 3

6. Operation Controls and Functions .............................................. 4

6.1 Front Panel ............................................................................... 4

6.2 Rear Panel ............................................................................. 5

6.4 Remote Control ....................................................................... 7

6.5 OLED Menu .............................................................................. 8

6.6 IR Cable Pin Assignment......................................................... 9

6.7 RS-232 Protocol ........................................................................ 9

6.8 RS-232 and Telnet Commands ............................................ 10

6.9 Telnet Control ........................................................................ 14

6.10 WebGUI Control .................................................................. 16

6.10.1 Video Switch ..................................................................... 18

6.10.2 Zone A/V Pairing .............................................................. 23

6.10.3 EDID Settings ..................................................................... 24

6.10.4 HDBaseT & H/W Info ......................................................... 26

6.10.11 User Cong ...................................................................... 27

6.10.12 System Settings ............................................................... 27

6.10.13 EDID Setting ................................................................... 28

6.10.13 Logout ............................................................................. 28

7. CONNECTION DIAGRAM ............................................................ 29

8. SPECIFICATIONS .......................................................................... 30

8.1 Technical Specications....................................................... 30

8.2 Supported Timing Table & Maximum HDMI Cable Length .... 31

8.3 Supported Audio Formats .................................................... 32

8.4 HDBaseT Features .................................................................. 33

8.5 CAT5e/6/7 Cable Specications ......................................... 34

9. ACRONYM ................................................................................... 35

1. INTRODUCTION

The PUV-44XPL-4K22 HDMI/HDBaseT Matrix supports the

transmission of video (resolutions up to 4K2K@60Hz, HDCP 2.2,

HDMI2.0) and multi- channel digital audio from 4 HDMI sources

to 4 HDBaseT outputs and 2 independent HDMI2.0 outputs.

HDBaseT outputs allow transmission via a single CAT5e/6/7

cable up to 70m, whilst the independent HDMI outputs support

cable lengths of up to 10m.

The LPCM7.1 CH, Dolby TrueHD, Dolby Digital Plus, Dolby Atmos

and DTS-HD Master Audio transmission are supported. Further,

the L/R analogue audio for each HDBaseT zones (outputs A to

D) are able to be breakout.

The Power over HDBaseT (PoH) function provides power to

compatible receivers.

Control is via manual selection buttons, IR, RS-232, Telnet or

WebGUI. CYP provide control drivers for all the major control

systems. The PUV-44XPL-4K22 is designed to be used with PUV-

1210PL-RX receivers that can utilize the PoH capabilities of the

matrix.

2. APPLICATIONS

•

Residential AV matrix installation

•

Commercial AV matrix installation

•

Security systems

•

University lecture hall systems

•

Retail installation systems

3. PACKAGE CONTENTS

• 1× 4x 6 Matrix system

• 1×24V DC Power Adaptor

• 4×IR Blaster

• 4×IR Extender

• 2×Racked Ear

• 1×Remote Control (CR-163)

• 1×UK Power Cord

• 1×Europe Power Cord

• 1×Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI equipped source devices

• HDMI equipped displays

• Compatible HDBaseT receivers – PUV-1210PL-RX

• Industry standard CAT6/7 cables

• HDMI cables – ‘Premium High Speed HDMI Cables’ are commended

with 6G HDMI sources.

5. FEATURES

• HDMI 2.0, HDCP1.4 and HDCP2.2 compliant

• Routes four HDMI sources to four displays using four HDBaseT outputs

and two independent or mirrored HDMI outputs

• Supported HDBaseT resolutions: VGA~WUXGA, 480i~1080p, 4K

UHD@24/25/30Hz (R:G:B 4:4: & Y:U:V 4:4:4 & Y:U:V 4:2:2), 4K UHD@

60Hz (YUV 4:2:0), dependent upon the output display’s EDID settings

• Supports resolutions up to 4K@60 (YUV 4:4:4) on HDMI output ports

• Supports automatic 4K@60 YUV 4:4:4 to YUV 4:2:0 conversion for

HDBaseT outputs

• 4K/2K & 4K UHD signals can be transmitted up to 35m via CAT5e/6

and 70m via CAT6a/7

• The LPCM7.1 CH, Dolby TrueHD, Dolby Digital Plus, Dolby Atmos and

DTS-HD Master Audio transmission are supported.

• Further, the L/R analogue audio for each HDBaseT zones (outputs A

to D) are able to be breakout.

• Advanced internal and external EDID management with 4 sets of

congurable EDID settings

• Bi-directional IR support over HDBaseT

• The Power over HDBaseT (PoH) function provides power to

compatible receivers.

• Control is via RS-232, remote control, on-panel control and IP

Control (Telnet & WebGUI)

• 1U rack mounted design

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER

LOCK

698710

ENTER

PRESET

/CANCEL

OUT

21 3 6 8 10

5 7 9

114

POWER: Press this button to power on/ off device.

POWER LED: The LED will illuminate in green when the power is on,

and shown in red when power off this device.

The network function will remain active once press this power off

button. This is for connected Receiver can get power when matrix

unit be power off.

IR WINDOW: Receiving remote control signal to control this device,

please use the remote control unit supplied in the package.

OUTPUT A~F & INPUT 1~4: Press “OUT” button to select the output

source (A~F). Next, press output keys (A~F) to select output source;

then press “IN” key to select input source (1~4). Finally, press “ENTER”

to conrm selection.

For example, if outputs A~D need to be assign to input 1, following

sequences of button presses need to be performed: OUT → A,B,C,D

→ IN → number key “1” →ENTER

If all output source would like to be assigned to single input, press

“OUT” button and all input buttons “A~F” then press “IN” and enter

the number key of input and enter to conrm the selection.

MENU & CANCEL: Press “MENU” button to access the LCM menu.

The menu tree please refers to section 17. Press “CANCEL” button

to cancel the selection.

ENTER: Press this button to conrm the selection.

PLUS (+)/IN: Press Plus “+” button to navigate up button selection.

Press “IN” button for input port sources selection.

MINUS (-)/OUT: Press Minus “-” button to navigate down button

selection. Press “OUT” button for output port sources selection.

LOCK: Press this button for three second to lock all buttons on

panel. The right top side will display “L” once front panel locked.

Press for few seconds to unlock.

PRESET: Press this button to recall preset setting, allow maximum

8 sets preset setting to recall. The preset settings are able to be

completed on WebGUI. Please refer to section 9.1.4 for advanced

preset setting.

LCM: The LCM displays the setting and information.

6.2 Rear Panel

95 7

8421

HDMI IN & IR Out 1 ~ 4: Connect to source devices with HDMI

interface and HDMI cable, the input source devices includes DVD

players, Set-top Boxes and so on. The qualied HDMI cables are

recommended. The DVI source is complaint; please use cable to

converts DVI to HDMI. The IR In provides customer to transmit the

IR signal to connected displays. Please use the remote control unit

supplied in the package.

CAT5e/6 OUT & IR IN A~D: Connect from these Cat5e/6 outputs to

input port of compatible Receivers with a single CAT5e/6/7 cable

for HDMI Audio/Video and IR/RS-232 control signal transmission.

The IR Out provides customer to transmit the IR signal to matrix unit

from display installation sites. Please use the remote control unit

supplied in the package.

ZONE AUDIO OUT: Four sets of audio output from HDBaseT output.

The ampliers are able to be connected for audio source

broadcasting.

IR IN (ALL): Connect an IR extender for IR signal reception. Ensure

that remote being used is within the direct line-of-sight of the

IR extender. IR signals received will transmitted by all IR blasters

connected to the matrix or Receivers.

IR OUT (ALL): Connect an IR Blaster for IR signal transmission to

the source/input location. Place the IR Blaster in direct line-

of-sight of the equipment to be controlled. It will transmit all IR

signals Received by any IR extenders connected to the matrix or

Receivers.

RS232: Connect to a PC or control system with D-Sub 9-pin cable

to control the matrix with RS-232 commands (refer to Sections 7)

CONTROL: Connects matrix unit with PC or laptop via RJ-45 cable

for Telnet or WebGUI control(the details of Telnet and WebGUI,

please refers to Sections 9 and 10).

SERVICE: Please plug in USB thumb drive to update Firmware in

eld. The USB thumb drive shall plug in and select update “YES” on

front panel and rmware in USB thumb drive to complete rmware

update.

MAIN 24V: Plug the 24 V main power supply in the package for

power on the matrix unit. If connect with POH Receiver, please

plug 24V power supply to POH outlet for supplying power over

cable to compatible Receiver with POH function.

6.3 Side Panel

FAN VENTILATOR: These are air ventilation areas, DO NOT block

these areas or cover it with any object. Please allow adequate

space around the unit for air circulation.

6.4 Remote Control

Power: Press this button to power the matrix

unit.

LOCK: Press this button to lock front panel of

matrix unit.

MUTE: Mutes Zone Audio outputs. HDBaseT

audio can only be muted when an

independent non HDMI audio has been

routed to these outputs.

INPUT 1~10 & OUTPUT A~J & Pattern: For

HDBaseT zone operation the user only needs

to select the desired input 1- 4. For Front

panel operation please refer to front panel

instructions.

NOTE: PUV-44XPL-4K22’s remote sends

commands based upon how the matrix has

been congured for the Zone AV Pairing

mode which is setup via the webGUI, please

refer to section 6.10.8

This remote control is for family series, the

pattern and mute function on PUV-44XPL-

4K22 is excluded.

PRESET: Recall preset setting back. The

preset settings are able to be congured on

WebGUI.

MENU/CANCEL: Press “Menu” button to access to menu selection

on LCM display. Press “Cancel” button to cancel selection.

PLUS (+)/IN: Press “+” to navigate up on menu selection. Press “In”

for input port number selection:

MINUS (-)/OUT: Press “-“ to navigate down on menu selection of

LCM display. Press “OUT” for output ports selection.

VOL UP/DOWN (+/-): This remote control is for family series, the

volume adjustment function on PUV-44XPL-4K22 is excluded, and

the volume could be adjusted on connected amplier.

POWERLOCKMUTE

1/A2/B 3/C

4/D5/E 6/F

7/G8/H 9/I

10/J PATTERN

+/IN

MENU/

CANCEL

PRESET

/VOL+

/VOL-

CR-163

ENTER

-/OUT

6.5 OLED Menu

LEVEL 2

LEVEL 3

LEVEL

EDID EDID Mode All/Independent

EDID Select All/1~6/7~12/13~16

(1~6=Default EDID

settings, 7~12=Sink’s

EDID settings,

13~16=User’s EDID

settings)

Network Link Status (Idle)

IP Address

Subnet Mask

Gateway Address

MAC Address

DHCP mode On/Off

HDMI Mirroring Output E/F

Factory Default Yes/No

Firmware Version

Update Yes/No

Note: The model name and IP address will be displayed when

power on the matrix unit. The mask and Gateway information

will be displayed once press “+” button on front panel or remote

control unit.

6.6 IR Cable Pin Assignment

Power

IR Signal

IR Blaster

IR Signal

Power

Grounding

IR Extender

6.7 RS-232 Protocol

MATRIX

►

◄

MATRIX

Pin Assignment Pin Assignment

2 TX 2 RX

3 RX 3 TX

4 NC 4 NC

5 GND 5 GND

6 NC 6 NC

7 NC 7 NC

8 NC 8 NC

9 NC 9 NC

Baud Rate: 115200bps

Data bit: 8 bits

Parity: None

Flow Control: None

Stop Bit: 1

6.8 RS-232 and Telnet Commands

Command DESCRIPTION

HDMI_Out M

VideoSrc=XXX

Video source of HDMI Tx out E~F.

M=E~F(Support multiple selection).

Available XXX:

HDMI_In n, n=1~4

HDMI_Out M

VideoSrc=Default

Reset Video source of HDMI Tx out to

factory default.

M=E~F(Support multiple selection).

HDMI_Out M

Mirroring=XXX

Audio/Video following source of HDMI Tx

out E~F.

M=E~F(Support multiple selection).

Available XXX:

HDBT_Out n, n=A~D

HDMI_Out M Status

Display HDMI E~F status & properties

including Aud/Vid matrix.

M=E~F(Support multiple selection).

HDMI_Out M

Name=”NameString”

Setup HDMI E~F verbose name.

M=E~F(Only support single selection).

HDBT_Out M

VideoSrc=XXX

Video source of HDBaseT Tx out A~D.

M=A~D(Support multiple selection).

Available XXX:

HDMI_In n, n=1~4

HDBT_Out M

VideoSrc=Default

Reset Video source of HDBT Tx out A~D to

factory default.

M=A~H(Support multiple selection).

HDBT_Out M Status

Display HDBT A~D status & properties

including Aud/Vid matrix.

M=A~D(Support multiple selection).

Command DESCRIPTION

HDBT_Out M

Name=”NameString”

Setup HDBT A~D verbose name.

M=A~D(Only support single selection).

HDMI_In M Status

Display HDMI In 1~4 status.

M=1~4(Support multiple selection).

HDMI_In M

Name=”NameString”

Setup HDMI In 1~4 verbose name.

M=1~4(Only support single selection).

SETIP <IP> <SubNet>

<GW>

Setting IP.SubNet.GateWay(Static IP)

RSTIP

IP Conguration Was Reset To Factory

Defaults(DHCP)

IPCONFIG Display the current IP cong

Power Off (Remain power supply to

Receiver and network )

P1 Power ON

P2 Power Off all

Report power status

PRESET Save M Save current A/V routing. M=1~8.

PRESET Load M Recall current A/V routing. M=1~8.

PRESET Show [M]

List current stored A/V preset. M=1~8.

If M is omitted, list all A/V preset.

PRESET name

M=”NameString”

Set verbose name of specied preset slot

EDID

All=EdidSetNumber

Set EDID of all input port =Specied EDID

set number. If EdidSetNumer=”Off”, it

becomes independent mode.

EDID HDMI_In

M=EdidSetNumber

Set specied HDMI input port M=Specied

EDID set number.

EDID M

Name=”NameString”

Set verbose name of specied EDID slot M.

Command DESCRIPTION

Display all available commands

Help

Display all available commands(Except

hidden commands)

Ver Show rmware version

ZoneAvPair HDBT_Out

M Slot N VideoSrc=XXX

Setup HDBT_Out zone side audio/video

pairing storage slot N video source.

M=A~D(Only support single selection).

N=1~4 (Support multiple selection).

Available XXX:

HDMI_In n, n=1~4

ZoneAvPair HDBT_Out

M Slot N Load

Load slot N of HDBT_Out zone side audio/

video pairing storage.

M=A~D(Only support single selection).

N=1~4 (Support multiple selection).

ZoneAvPair HDMI_Out

M Slot N VideoSrc=XXX

Setup HDMI_Out zone side audio/video

pairing storage slot N video source.

M=E~F(Only support single selection).

N=1~4 (Support multiple selection).

Available XXX:

HDMI_In n, n=1~4

ZoneAvPair HDMI_Out

M Slot N Load

Load slot N of HDMI_Out zone side audio/

video pairing storage.

M=E~F(Only support single selection).

N=1~4 (Support multiple selection).

Command DESCRIPTION

IR_Route HDBT_Out M0

M1 M2

Setup IR source of HDBT Rx end IR out jack.

M0=Output port index. M0=A~D (Support

multiple selection)

M1=Route operation. Available M1:

Add: Add M2 input source to HDBT_Out.

Del: Delete M2 input source from HDBT_

Out.

M2=Input source. Available M2:

IR_InAll: IR In all input jack.

Generator: Internal IR encoder.

IR_Route HDBT_Out M0

Show

Print current IR source of HDBT Rx end IR

out jack.

M0=Output port index. M0=A~D (Support

multiple selection)\

IR_Route IR_Out_Out

M0 M1 M2

Setup IR source of IR_Out jack aside of

each HDMI In connector.

M0=Output port index. M0=1~4 (Support

multiple selection)

M1=Route operation. Available M1:

Add: Add M2 input source to IR_Out.

Del: Delete M2 input source from IR_Out.

M2=Input source. Available M2:

IR_InAll: IR In all input jack.

Generator: Internal IR encoder.

IR_Route IR_Out M0

Show

Print current IR source of IR_Out jack aside

of each HDMI In connector.

M0=Output port index. M0=1~4 (Support

multiple selection)

HdcpOut Show

Display HDCP mode setting when video

out

<any Command> Display instruction of that command

Note: All commands are case-insensitive.

6.9 Telnet Control

Before attempting to use the Telnet control, please ensure that both

the Matrix (via the ‘LAN /CONTROL’ port) and the PC/Laptop are

connected to the same active networks.

To access the Telnet control in Windows 7, click on the ‘Start’ menu

and type “cmd” in the Search eld then press enter.

Under Windows XP go to the ‘Start’ menu and click on “Run”, type

“cmd” with then press enter.

Under Mac OS X, go to Go→Applications→Utilities→Terminal

See below for reference.

Once in the command line interface (CLI) type “telnet”, then the IP

address of the unit and “23”, then hit enter.

This will bring us into the unit which we wish to control. Type “help” to

list the available commands.

Note: 1. Commands will not be executed unless followed by a

carriage return. Commands are case-sensitive. If the IP is

changed then the IP Address required for Telnet access will

also change accordingly.

2.The P2 command not support when operate Telnet due to

need to reserve power for network active

6.10 WebGUI Control

• Install the IP Discovery Tool:

(1)

Connect the Matrix to a PC with a Ethernet connection (via the

‘LAN/CONTROL’ port). Please ensure your PC is on the same

active network as the Matrix before running the application.

(2)

Please download the ZIP le from our website and save it in

a directory where you can easily nd it again. Once de-com-

pressed, the application is a direct executable le.

(3) Click twice on the application to open it. Click the “Find De-

vices on Network” button to scan the connected network. This

will locate the compatible devices on that network.

(4) The devices will then be listed and displayed on the window.

For further features, click the device name to bring up a

second window where you can change the IP settings and

launch the WebGUI control.

Note: The default IP address of the Matrix is ‘192.168.1.50’.

(5) Once changed, click the ‘Save’ and then ‘Reboot’ buttons

to update the IP settings of the Matrix.

CYP PUV-44XPL-4K22-KIT User manual

Related papers

Other documents