Minuteman M26036TDCE User manual

Minuteman
Brand
Minuteman
Model
M26036TDCE
Category
Floor Machine
Type
User manual

This manual is also suitable for

Lumina 20 Traction Drive Battery Burnisher
Parts and Instruction Manual
• Stop on level surface.
• Disconnect the power to the machine by pulling the red Battery Connector located under the recovery tank near the batteries.
• Avoid moving parts. Do not wear loose jackets, shirts, or sleeves when working on machine.
• Avoid contact with battery acid. Battery acid can cause burns. When working on or around batteries, wear protective clothing and
safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of batteries.
• Do not clean machine with a pressure washer.
• Authorized personnel must perform repairs and maintenance. Use Minuteman supplied replacement parts.
For Safety When Servicing or Maintaining Machine
Lumina 20 Traction Drive Battery Burnisher
Model Lumina 20 Traction Drive
Model No. M26036TDQP / / M26036TDQPIW / M26036TDCE
Brush Speed 2600 RPM
Motor 2.5HP
Voltage, Batteries 36 volts, 3-12volt
Battery Capacity 165 AH
Gross Weight 916 lbs (415 kg) with batteries
638 lbs (290 kg) without batteries
Technical Specifi cations
Page 3
Lumina 20 Traction Drive Battery Burnisher
Declaration of Conformance
Page 4
Lumina 20 Traction Drive Battery Burnisher
Table of Contents
Technical Specifi cations .............................................................................................2
Declaration of Conformance ......................................................................................3
Safety Instructions ......................................................................................................5
Operating Instructions ................................................................................................6
Inspection .................................................................................................................6
Electrical...................................................................................................................6
Batteries ...................................................................................................................6
Operation .................................................................................................................6
After Use ..................................................................................................................7
Maintenance.............................................................................................................7
Floor Seal Strip ........................................................................................................7
Battery Service and Installation................................................................................7
Charging of Batteries ...............................................................................................7
Battery Cable Routing ..............................................................................................7
Pad Installation.........................................................................................................8
Pad Pressure Adjustments ......................................................................................8
Circuit Breaker Protection ........................................................................................8
Carbon Brush Replacement .....................................................................................8
Carbon Brush Service ..............................................................................................8
Machine Overview .......................................................................................................9
Dashboard Control Panel .........................................................................................10
Exploded Views .........................................................................................................12
Base Assembly.......................................................................................................12
Base Assembly BOM .............................................................................................13
Mainframe Assembly ..............................................................................................14
Mainframe Assembly BOM.....................................................................................15
Housing Assembly..................................................................................................16
Housing Assembly BOM ........................................................................................17
Pad Driver Assembly ..............................................................................................18
Pad Driver Assembly BOM.....................................................................................19
Pressure Control Assembly ....................................................................................20
Electrical Assembly ................................................................................................21
Console Assembly..................................................................................................22
Console Assembly BOM ........................................................................................23
Dashboard Assembly .............................................................................................24
Wiring Diagram ..........................................................................................................25
Warranty .....................................................................................................................28
Lumina 20 Traction Drive Battery Burnisher
Page 5
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: Operators must read and understand this manual before operating or maintaining this
machine.
Keep hands and feet clear of moving parts while machine is in operation.
Disconnect the power to the machine by pressing the Red Emergency Disconnect Button when
charging batteries or during installation or removal of pads.
During operation, loose objects on the fl oor can become dangerous projectiles if struck by the high
speed pad. Special attention should be paid in removing or avoiding loose fl oor tile, electrical cables
and telephone connection boxes.
Electrical motors and components can cause an explosion when operated near explosive materials
or vapors. Do not operate this machine near fl ammable materials such as solvents, thinners, fuels,
grain dust, etc.
Keep machine moving to reduce the risk of damaging fl oor fi nish and fl oor.
Make sure the Red Emergency Disconnect Button is pressed and the battery connector is unplugged
from the machine before performing any maintenance procedures.
Store or park this machine on a level surface only.
These machines are designed for level fl oor operation only. Do not operate on ramps or inclines.
Battery acid can cause burns. When working on or around batteries, wear protective clothing and
safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of batteries.
Charging batteries generates explosive gases. DO NOT CHARGE BATTERIES WHEN OPEN
FLAMES OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger is turned off
before disconnecting it from the machine. Charge the batteries in a well-ventilated area with the
battery cover removed completely.
Maintenance and repairs must be performed by authorized personnel.
SAVE THESE INSTRUCTIONS
Safety Instructions
Lumina 20 Traction Drive Battery Burnisher
Page 6
Operating Instructions
Inspection
Carefully unpack and inspect your burnisher for shipping damage. Each unit is tested and thoroughly inspected
before shipment; any damage is the responsibility of the delivery carrier who should be notifi ed immediately.
Electrical
This machine is battery operated and designed to operate on 36 volts DC (3) 12 volt batteries.
Batteries
Burnishers are shipped with batteries. (3 required)
Part No. 956210 12V 210AH 20 Hr. Rate
We do not recommend mixing AMP hour capacities. Any alternate battery sets can be used if they equal physical
size and capacity. See next page for service and installation.
Operation
Before starting, familiarize yourself with the machine and its controls (see “Machine Overview” and “Dashboard
Control Panel” diagrams). To turn the machine ON, do the following:
1. Make sure 20” high speed pad is used. Make sure the pad is installed on the machine by following instructions
under “Pad Installation.”
2. Make sure that no battery charger is plugged into the recharge port.
3. Lift the red emergency disconnect button so it is in the up position.
4. Lower the pad driver assembly by pushing the pedal slightly outward on the machine (unlock it), and then
release it slowly.
5. Turn the key switch to the ON position. The pad driver will then slowly adjust itself to the fl oor. Make sure the
machine is set to move forward indicated by the light on the dashboard control panel.
6. Place hands on the bails and squeeze the bail levers to start the operation of the machine. Move forward in a
straight line, check the reading on the Operating Range Meter and make sure you are in the Green Zone.
7. Adjust the pad pressure as needed by turning the knob accordingly. (See Pad Pressure Adjustments.)
8. Adjust speed as needed by turning the speed control knob accordingly.
Lumina 20 Traction Drive Battery Burnisher
Page 7
After Use
To raise the pad driver, push down until the pedal arm engages into the pedal catch. Turn machine off by turning the
key switch on the control panel. Machine can be cleaned with a mild detergent and a damp cloth. Batteries should be
charged after each use or when the battery condition meter shows a low charge. Once the battery charger reads 0
amps, the batteries are recharged. This should take approximately 8 hours if the batteries are completely discharged.
Maintenance
Periodically remove batteries from machine. Clean the batteries and battery tray with a solution of baking soda and
water. Check all battery cables and wiring for signs of damage and wear. Replace as needed. Grease front wheel
and rear caster zerks once a month for best operation.
Floor Seal Strip
When the fl oor seal strip show signs of excessive wear, seal should be replaced. The strip can be removed by
loosening the screw on the retainer strap until the seal can slide off of the pad shroud housing. To install new seal,
slip the retainer strap over the new seal strip and pad shroud. Make sure the seal is seated equally around the
perimeter and the holes on the fl oor seal are oriented towards the back portion of the shroud.
Battery Service and Installation
WARNING: Battery acid can cause burns. When working on or around batteries, wear protective clothing and safety
glasses. Remove metal jewelry. Do not lay tools or metal objects on top of batteries.
Charging of Batteries
Charging batteries generates explosive gasses. DO NOT CHARGE BATTERIES WHEN OPEN FLAMES OR
SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger is turned off before disconnecting it from the
batteries. Charge the batteries in a well-ventilated area with battery cover removed completely. Fluid levels should
be checked before and after charging and maintained at the proper levels. If the burnisher is not used for extended
periods of time, batteries should be kept fully charged with a boost charge once a week.
Battery Cable Routing
Lumina 20 Traction Drive Battery Burnisher
Page 8
Pad Installation
The red emergency disconnect button and the key switch must be in the OFF position before installation and the pad driver
assembly in the RAISED position. Remove center cup locking device by gripping on outer edges and turning clockwise.
NOTE: Center cup cannot be pulled out; it must be unscrewed. After removing used pad, place new pad on pad driver
assembly using outer fl ange of pad driver to center the pad. Push centering locking cup through the pad and into the pad
driver assembly. The ratchet teeth on the center cup will engage into the pad driver assembly and should be pushed in as
far as possible. If further tightening is needed, rotate the center-locking cup counter-clockwise
Pad Pressure Adjustments
The pad pressure adjust knob is located on the top of the control console. Counter-clockwise rotation increases pad
pressure, the opposite rotation decreases. Diff erent fl oors, conditions, and pads produce carrying pad load conditions.
Ideal burnishing conditions are maintained while the operating range meter remains in the Green Zone. If the meter reads
in the Red Zone decrease the pad pressure. When the machine is operated in the Red Zone for a long period of time
motor overload will occur and the 70-amp circuit breaker for the motor will trip. If the motor circuit trips:
1. Check pad condition.
2. Decrease pad pressure.
3. Reset circuit breaker.
Circuit Breaker Protection
70 amp circuit breaker protects pad driver motor from excessive overload conditions. 3.0 amp circuit breaker protects
control circuits against possible electrical shorts. If either circuit breaker trips, fi rst determine the cause and correct the
condition before resetting the breakers.
Carbon Brush Replacement
Design life of carbon brushes is between 1800-2000 hours. Replace brushes if worn to 3/8” or less, broken, or chipped. All
carbon brushes should be replaced when motor is serviced. Four (4) are required, P/N 572003. Red indicator on control
panel (above Emergency Disconnect Button, below the Dashboard) will glow when carbon brush service is required.
Carbon Brush Service
1. Disconnect batteries from machine.
2. Remove two screws that hold dust control housing and motor cover to motor.
3. Blow out top of motor with air line.
4. Loosen screw and remove carbon brush lead.
5. Slide brush spring off the back of carbon brush and remove brush.
6. Reverse order for installation of new carbon brushes.
Lumina 20 Traction Drive Battery Burnisher
Page 9
Machine Overview
A
C
B
D
E
G
H
I
J
K
L
F
A
B
C
D
E
F
G
H
I
J
K
L
PAD PRESSURE ADJUSTMENT
BAIL LEVER
DUST BAG
DASHBOARD CONTROL PANEL
EMERGENCY BELLY BAR STOP
CARBON BRUSH INDICATOR
EMERGENCY STOP BUTTON
POWER CONNECTOR
CIRCUIT BREAKER, 70 AMP
CIRCUIT BREAKER, 3 AMP
CIRCUIT BREAKER, 18 AMP
FOOT PEDAL
Lumina 20 Traction Drive Battery Burnisher
Page 10
Dashboard Control Panel
A
C
B
D
E
F
A
B
C
D
E
F
ON / OFF KEY SWITCH
TRACTION DRIVE DIRECTION INDICATOR
TRACTION DRIVE DIRECTIONAL SWITCH
BATTERY GUAGE
TRACTION DRIVE SPEED CONTROL
PAD PRESSURE GUAGE
Lumina 20 Traction Drive Battery Burnisher
Page 11
Notes
Lumina 20 Traction Drive Battery Burnisher
Page 12





























Exploded Views
Base Assembly
Lumina 20 Traction Drive Battery Burnisher
Page 13
Base Assembly BOM
BILL OF MATERIAL
ITEM PART NO. QTY DESCRIPTION
1 200126 2 TRANSAXLE MOUNT 11GA
2 200154 1 ELECTRICAL BOX COVER 14GA
3 172167 2 CASTER, 3 1/2" PU WHEEL
4 210141 2 WHEEL-8 X 1.5 X .75 BORE
5 260224 1 DRAIN HOSE 1/4 X 18 SILICONE
6 260536 1 WELD-PLATE BASE
7 260541 1 REAR HANDLE BRKT
8 260549 1 PRESS ADJ ASSY
9 260579 1 CLIP-TOOL 1.5 INCH HOSE
10 260683 1 CONSOLE ASY, 2600TD SPE BAT GAUGE
12 260604 1 TRAY, BATTERY
13 260676 2 SPACER, TRANSAXLE
14 320271 1 FITTING-PP 90 11/16-16UNC X 3/8HOSE
15 320272 2 NOZZLE BODY LOCKNUT
16 320273 1 CLAMP-HOSE SHUT-OFF
17 361233 2 KEY-SQ 3/16 X 1-1/2
18 711124 6 SCR-PHSMS 10 X .37 ZP B POINT
19 711160 11 SCR-HI/LO 10 X .625 BLACK ZINC
20 711229 4 SCR-HH 5/16-18 X .87 ZP GR 5
21 711505 23 WASHER-FLAT 1/4 ZP
22 711507 4 WASHER-FLAT 3/8 X 1.12 X .06
23 711519 10 WASHER-FLAT 1/4 X 1.00 X .06 ZP
24 711544 27 WASHER-LOCK 1/4 SPLIT ZP
25 711545 4 WASHER-LOCK 5/16 SPLIT ZP
26 712042 2 SCR-HH 5/16-18 X.62 ZP GR 5 FLANGE
27 712318 4 WASHER-FLAT 3/4 X 1.12 X .12 ZP
29 712759 2 WASHER-FLAT .31 X 1.37 X .06 SS
30 743800 1 TRANSAXLE- 36VDC
31 743847 1 ELEC ASSY, BATTERY BURN
32 200102MCH 1 2600 BASE
Lumina 20 Traction Drive Battery Burnisher
Page 14
Mainframe Assembly









































 











Lumina 20 Traction Drive Battery Burnisher
Page 15
Mainframe Assembly BOM
BILL OF MATERIAL
ITEM PART # QTY DESCRIPTION ITEM PART # QTY DESCRIPTION
1 260536 1 WELD-PLATE BASE 28 260528 1 LINK
2 260577-1 1 SWITCH INTERLOCK BRKT NEW 29 260529 2 TRAILING LINK
3 711503 2 WSR-FLAT #10 X .50 ZP 30 260513 1 WELD-LIFT MOTOR
4 711350 2 NUT-NYLOC 10-32 ZP 31 712102 1 BLT-SHLDR 1/2 X 1.5 LG X 3/8-16
5 740830 1 SW-SNAP SPST NO/NC
CONTACTS FLAT LEVER
32 712301 1 WSR-FLAT 3/8 X .87 X .06 ZP
6 711501 2 WSR-FLAT #6 X .375 ZP 33 711380 1 NUT-NYLOC 3/8-16 ZP
7 710307 2 SCR-PHMS 6-32 X 1.00 ZP 37 210142 1 PEDAL PAD
8 711430 1 NUT-TINNERMAN 6-32 38 260586 1 SUPPORT, BATTERY LOWER
9 260522 1 SPRING GUIDE 39 260587 1 SUPPORT, BATTERY UPPER
10 670605 2 ROLLER PIN 40 712139 4 SCR-HH 1/4-20 X .50 ZP THREAD
ROLLING
11 711506 8 WSR-FLAT 5/16 X .688 ZP 41 711229 4 SCR-HH 5/16-18 X .87 ZP GR 5
12 711721 4 RET RING-E TYPE .312 42 260615 1 WELD-PLATE MOTOR NEW
13 260524 2 ADJUSTMENT LINK 44 260519 2 PIVOT PIN
15 831965 1 PIN-CLEVIS 3/8 X 1.63 45 712310 12 WSR-FLAT .52 X .87 X .06 ZP
16 711808 1 PIN-HAIRPIN COTTER #13 46 711713 6 RET RING-E EXT .50
17 260511 1 WELD-UPPER 48 260525 1 ADJUSTMENT NUT
18 260521 1 GUIDE TUBE 49 712905 1 NUT-HEX 10-24 SS
19 711511 1 WSR-FLAT 5/8 X 1.31 X .09 SS 51 743644 1 DIN RAIL, CUT- 2"
20 762339 1 SPRING-COMP 52 711503 2 WSR-FLAT #10 X .50 ZP
21 260523 1 SPACER-1.5 X .632 X .84 53 711543 2 WSR-LOCK #10 SPLIT ZP
22 260519 2 PIVOT PIN 54 710356 2 SCR-RHMS 10-32 X .62 ZP
23 711592 2 WSR-FLAT 1/2 X .90 X .064 NYLON 55 743640 1 TERMINAL BLOCK-60A RED
(SPRING ACTION)
24 712310 19 WSR-FLAT .52 X .87 X .06 ZP 56 743641 1 TERMINAL BLOCK-60A BLACK
(SPRING ACTION)
25 711713 6 RET RING-E EXT .50 57 743642 1 TERMINAL BLOCK-END PLATE
(SPRING ACTION)
26 711524 6 WSR-WAVE .52 X .87 X .01 58 743643 2 TERM BLOCK-END ANCHOR
(SPRING ACTION)
27 260576 1 LINK, SWITCH BRKT
Lumina 20 Traction Drive Battery Burnisher
Page 16















Housing Assembly
Lumina 20 Traction Drive Battery Burnisher
Page 17
Housing Assembly BOM
BILL OF MATERIAL
ITEM PART NO. QTY DESCRIPTION
1 260501 1 FIXED TOP COVER
2 260502 1 TOP COVER REAR
3 260503 1 BAG COVER TOP
4 260504 1 PLATE-FILTER COVER
5 260560 1 HINGE-9.75"
6 260592 1 EXHAUST FILTER DUST CONTROL
7 260596 1 INSERT FITTING 1-1/2" PVC FPT FEM ADAP
8 310008 1 O-RING-BUNA 1.375 ID
9 320246 1 SOLUTION TNK CABLE
10 450037 1 ADAPTER MACHINED
11 450081 1 WASHER-FLAT 1.908 X 2.41 X .03 SS
12 450207 1 LATCH-SOFT
14 710180 3 SCR-THMS 1/4-20 X .75 ZP
15 711160 10 SCR-HI/LO 10 X .625 BLACK ZINC
16 711228 4 SCR-HH 5/16-18 X .75 ZP GR 5
17 711373 4 NUT-NYLOC 1/4-20 ZP
18 711374 4 NUT-NYLOC 5/16-18 ZP
19 711425 1 NUT-FLANGED WIZZ 1/4-20 ZP
20 711506 4 WASHER-FLAT 5/16 X .688 ZP
21 711516 4 WASHER-FLAT 5/16 X 1.25 X .05 ZP
22 711519 3 WASHER-FLAT 1/4 X 1.00 X .06 ZP
23 712761 2 WASHER-FENDER 1/4 X 1.25 X .059 SS
24 828970 1 WSR NEOP 1.87X2.4X.125
25 831001 1 CLAMP-CRIMP 440R
Lumina 20 Traction Drive Battery Burnisher
Page 18












Pad Driver Assembly
Lumina 20 Traction Drive Battery Burnisher
Page 19
Pad Driver Assembly BOM
BILL OF MATERIAL - 260610
ITEM PART NO. QTY DESCRIPTION
1 260573 1 MOTOR GRILL ASSY
2 260597 1 KEY, 3/6 X .906
3 260611 1 PAD DRIVER SHROUD - 20"
4 260615 1 WELD-PLATE MOTOR NEW
5 260616 1 DUST SKIRT - NEW
6 260619 2 PAD DRIVER STRAP
7 670075 1 MULTIFLEX PADRVR ASSY-BATTERY BURNISHER
8 710857 1 SCR-SHCS 5/16-24 X 1.00 BLL OX
9 711124 2 SCR-PHSMS 10 X .37 ZP B POINT
10 711505 3 WASHER-FLAT 1/4 ZP
11 711512 4 WASHER-FLAT 3/4 X 1.37 X .08 ZP
12 711516 1 WASHER-FLAT 5/16 X 1.25 X .05 ZP
13 711544 7 WASHER-LOCK 1/4 SPLIT ZP
14 711545 1 WASHER-LOCK 5/16 SPLIT ZP
15 712070 4 BLT-SHOULDER 5/16 X .75 LG X 1/4-20 BLK
16 712537 14 SCR-THMS 10-24 X .75 SS
17 713003 3 SCR-HH 1/4-20 X 1.00 ZP GR 5
18 742461-2 1 MOTOR ASSEMBLY
19 809857 4 SPRING-CONICAL STL
20 260581MCH 1 PAD GRABBER, RING MACHINED
21 760401 1 CENTER CUP (
INCLUDED WITH ITEM #7 670075)
Lumina 20 Traction Drive Battery Burnisher
Page 20
Pressure Control Assembly





BILL OF MATERIAL - 260549
ITEM PART NO. QTY DESCRIPTION
1 260066 1 BUSHING-FLG .377 X .50 X .31 OILITE
2 260547 1 WELD-PRESS ADJUST
3 260554 1 PRESS ADJ SCREW
4 260557 1 PRESS ADJ SLIDE
5 260562 1 PRESS ADJ RET BRKT
6 260563 1 PRESS ADJ RET BRKT
7 260564 1 PIN-ROLL 3/16 X 3/4
8 710353 4 SCR-PHMS 10-32 X .37 ZP
9 711391 1 NUT-JAM 3/8-16 ZP
10 712536 1 SCR-THMS 10-24 X .62 SS
11 715038 1 DECAL-PAD PRESSURE
12 760034 1 KNOB-ADJ 3/8-16 THREAD
13 762253 1 CABLE-PRESSURE ADJ ASSY
14 833102 1 SPRING-KNOB .60 X .73 X 1.75 ZINC
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

Minuteman M26036TDCE User manual

Minuteman
Brand
Minuteman
Model
M26036TDCE
Category
Floor Machine
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents