iogear GCS1222TAA3 User manual

Brand: iogear

Model: GCS1222TAA3

Category: KVM switches

Type: User manual

This manual is also suitable for

GCS1324TAA3

2/4/8-Port USB DVI/HDMI/DisplayPort

GCS1212TAA3 – GCS1214TAA3 – GCS1218TAA3 – GCS1222TAA3 – GCS1224TAA3 – GCS1228TAA3

GCS1312TAA3 – GCS1314TAA3 – GCS1318TAA3 – GCS1322TAA3 – GCS1324TAA3 – GCS1328TAA3

GCS1412TAA3 – GCS1414TAA3 – GCS1418TAA3 – GCS1422TAA3 – GCS1424TAA3 – GCS1428TAA3

Single/Dual View Secure

KVM Switch User Manual

www.iogear.com

Manual Version: v1.02

Manual Date: 2017-10-24

Table of Contents

FCC Information 4

Package Content 6

Chapter 1 - Introduction 8

Features 9

Requirement 10

Operating System 11

Overview 12

Chapter 2 - Hardware Setup 16

Chapter 3 - Operation 22

Appendix 25

Specications

Limited Warranty 32

FCC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has

been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. Any changes or modications made to this equipment may void the user’s authority

to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy. If not

installed and used in accordance with the instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to connect the interference by one or more

of the following measure:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio / TV technician for help

FCC Caution: Any changes or modications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired

operation

RoHS

This product is RoHS compliant.

User Notice

User Information

All information, documentation, and specications contained in this manual are subject to change without

prior notication by the manufacturer. The manufacturer makes no representations or warranties, either

expressed or implied, with respect to the contents hereof and specically disclaims any warranties as to

merchantability or tness for any particular purpose. Any of the manufacturer’s software described in this

manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer

(and not the manufacturer, its distributor, or its dealer) assumes the entire cost of all necessary servicing,

repair and any incidental or consequential damages resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and / or TV interference caused by unau-

thorized modications to this device. It is the responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation of this system if the correct

operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE

SETTING IS CORRECT BEFORE USE.

Warranty Information

This product carries a 4 Year Limited Warranty. For the terms and conditions of this warranty, please go to

http://www.iogear.com/support/warranty

Online Registration

Please make sure to register your product online at

https://www.iogear.com/registration

Contact

Please contact our support team for any assistance

GovSupport@iogear.com

Package Content

IOGEAR Secure KVM package consists of:

1 x IOGEAR Secure KVM Switch

1 x Power Cord

1 x User Manual*

Please check to make sure that all of the components are present and are in good order. Please contact

your dealer if anything was missing or damaged in shipping.

Please read this manual thoroughly and follow the installation and operation procedures carefully to

prevent any damage to the switch or to any other devices on IOGEAR Secure KVM installation.

*Please visit our website to download the most up-to-date version of the manual

ATTENTION

If the tamper-evident seals are missing or peeled, avoid using the product and contact your

IOGEAR dealer.

If all front panel LEDs (except for Power LED) ash continuously or the switch’s enclosure

appears to be breached, avoid using this product and contact your IOGEAR dealer.

This Secure KVM Switch is equipped with active always-on chassis intrusion detection

security. Any attempt to open the enclosure will permanently damage, disable the switch,

and void the warranty.

Tamper-evident seal

About This Manual

This User Manual is intended for System Administrators and end users

Please read this user manual thoroughly to help you get the most from your IOGEAR Secure KVM Switch

system. This manual covers all aspects of installation, conguration, and operation. An overview of the

information found in the manual is provided below.

This User Manual covers the following IOGEAR Secure KVM

Conventions

This manual uses the following conventions:

Product Information

For information about all IOGEAR products and how they can help you connect without limits, visit

IOGEAR on the Web or contact an IOGEAR Authorized Reseller. Visit IOGEAR on the Web for a list of

locations and telephone numbers:

www.IOGEAR.com

Conguration 2-Port 4-Port 8-Port

PC Video

Connection

Console Video

Connection

Number of

Displays

DisplayPort HDMI Single GCS1412TAA3 GCS1414TAA3 GCS1418TAA3

Dual GCS1422TAA3 GCS1424TAA3 GCS1428TAA3

HDMI HDMI Single GCS1312TAA3 GCS1314TAA3 GCS1318TAA3

Dual GCS1322TAA3 GCS1324TAA3 GCS1328TAA3

DVI DVI Single GCS1212TAA3 GCS1214TAA3 GCS1218TAA3

Dual GCS1222TAA3 GCS1224TAA3 GCS1228TAA3

Monospaced Indicates text that you should key in

[ ] Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need

to be pressed together, they appear together in the same bracket with a plus sign between them:

[Ctrl+Alt]

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

→ Indicates selecting the option (on a menu or dialog box, for example), that comes next.

For example, Start → Run means to open the Start menu, and then select Run.

Indicates critical information

Chapter 1 - Introduction

Overview

The IOGEAR Secure KVM Switch series is NIAP-certied and compliant with NIAP PP 3.0 (Protection

Prole for Peripheral Sharing Switch version 3.0) requirements, satisfying the latest security requisites

set by the U.S. Department of Defense for peripheral sharing switches. Compliance ensures maximum

information security while sharing a single set of HIDs (keyboards, mice, speakers, and CAC Readers)

between multiple computers. Conformity with Protection Prole v3.0 certies that only a keyboard and

a mouse are accommodated, other USB peripherals cannot be connected to the console ports of the

Secure KVM; therefore, providing high-level security, protection and data safekeeping.

The IOGEAR Secure KVM Switch provides the utmost hardware and software security when switching

port focus. Hardware security includes tamper-evident tapes, chassis intrusion detection, and tamper-

proof hardware. Software security includes restricted USB connectivity, meaning non-HIDs (Human

Interface Devices) are ignored when switching. This security includes channel isolation per port and auto-

matic clearing of the keyboard and mouse buffer when switching port focus, making it impossible for data

to be leaked or transferred between secure and unsecure computers.

By combining physical security with controlled USB connectivity and controlled unidirectional data ow

from devices to connected computers only, the IOGEAR Secure KVM Switch series offers the means to

consolidate multiple workstations of various security classication levels with one keyboard, one video

monitor, and one mouse (KVM) console.

Administrative Functions

To be compliant with Protection Prole 3.0 while providing higher deployment exibility, wider product

support for new authentication devices, and maximum security, the IOGEAR Secure KVM Switch offers

Port Authentication Utility. IOGEAR Port Authentication Utility allows authorized administrators to con-

gure IOGEAR Secure KVM Switch to either accept or reject specic USB devices. Through a secured

access and authentication process, authorized administrators can perform congurable device ltering

through the Port Authentication Utility.

Note:

1. The National Information Assurance Partnership (NIAP) is a United States government initiative

to meet the security testing needs of IT consumers and manufacturers. NIAP is operated by the

National Security Agency (NSA) and the National Institute of Standards and Technology (NIST).

2. IOGEAR Secure KVM Switch series additionally satised Protection Prole version 3.0 for Periph-

eral Sharing Switch (PSS).

Features

Features Benets

2/4/8-Port USB DVI/HDMI/DisplayPort

Single/Dual View Secure KVM Switch

Reduces the costs involved in controlling up to 8

Single/Dual View computers while offering data

isolation between shared peripherals and computers

Superior ultra-high video resolution- up

to 4K UHD (3840 × 2160 @30Hz)*

Supports resolution up to 3840 x 2160@30Hz* with

crystal clear image quality

Video DynaSyncTM – exclusive IOGEAR

technology

IOGEAR Video DynaSyncTM eliminates boot-up display

problems and optimizes resolution when switching

between ports

DisplayPort AUX channel ltering

(DisplayPort Secure KVM Switch only)

Non-qualied auxiliary channel trafc such as MCCS and EDID write are rejected.

NIAP PP PSS v3.0 certied Provides the most advanced security features

required by the latest Protection Prole (PP) v3.0 for

Peripheral Sharing Switch (PSS)

Pushbutton Port Selection and secure

port switching

Port selection only via Pushbutton to enhance security. Keyboard, Mouse, Video, Audio

and CAC reader will switch together for secure switching.

Channel Isolation Isolated channel per port — making it impossible for data to be leaked or transferred

between computers.

Shared peripherals and computer

isolation

Console USB and PS/2 keyboard/mouse are supported. The always-on Keyboard, Mouse,

and

Display EDID emulation ensures isolation between peripherals and connected computers.

Keyboard, Mouse, and Video EDID

emulation

Keyboard, Mouse, and EDID emulation ensures isolation between peripherals and

connected computers.

Restricted USB connectivity Non-authorized HIDs (Human Interface Devices) or

non-predened CAC will be rejected / ignored

Unidirectional data ow Secure design enables unidirectional data ow

between devices and connected computers

Administrative conguration and event log

functions

Secure access for authorized Administrator to audit

KVM operation logs and secure conguration.

(Please refer to Administrator’s Guide)

Supports analogue audio (Speaker only)** Only unidirectional speaker data is allowed

preventing the passage of the analog audio by

microphone input or line input

Active always-on chassis intrusion

detection

If the cover is removed from the switch, the unit

becomes inoperable and front panel LEDs (except for Power LED) will ash continuously

Clears keyboard buffer when switching Keyboard data buffer is automatically purged when

switching KVM port focus

Tamper-proof hardware All integrated circuits are soldered directly to the

circuit board to prevent tampering with the

components

Tamper-evident tape Provides a visual indication of any attempt to gain

access to the switch’s internal components

Tamper-evident tape Provides a visual indication of any attempt to gain

access to the switch’s internal components

Firmware non-reprogrammable Prevents tampering and attempts to reprogram the

switch’s rmware

Metal enclosure Rugged metal enclosure

Note:

* IOGEAR HDMI and DisplayPort Secure KVM Switch series supports console video output resolution up to 4K UHD 3840 x 2160 @30Hz.

** IOGEAR Dual-Link DVI Secure KVM Switch series supports 3840 x 2160 @30Hz video output on compatible HDMI-interfaced monitors

and / or computers used with IOGEAR’s DVI-to-HDMI KVM cables

*** Only analog speaker data input is supported. The IOGEAR Secure KVM does not convert digital audio to analog audio.

Requirements

Console

• DVI (for DVI-interfaced Secure KVM) or HDMI (for HDMI and DisplayPort-interfaced Secure KVM)

monitor capable of the highest resolution that will be used on any computer in the installation

• Standard wired USB mouse

• Standard wired USB keyboard

• Standard wired PS/2 mouse (Optional)

• Standard wired PS/2 keyboard (Optional)

• Speaker (Optional)

• USB Smart card or CAC (Common Access Card) reader (Optional)

Computers

• a DVI/HDMI/DisplayPort Video output connector

• a USB Type A port for keyboard and mouse

• a USB Type A port for Smart Card or CAC reader (Optional)

• a 3.5mm jack Audio port for speaker (Optional)

Cables

The KVM cable sets which are specically designed to work with this switch are not supplied in the

package and require a separate purchase.

For security, do not connect any cable that has a microphone audio input or line in audio input

Operating Systems

Suggested operating systems are shown in the table, below:

Note: Supports Linux Kernel 2.6 and higher

OS Version

Windows 2000 / XP / Vista / 7 / 8 /

8.1 / 10

Linux RedHat 6.0 and higher

SuSE 8.2 and higher

Mandriva (Mandrake) 9.0 and higher

UNIX AIX 4.3 and higher

FreeBSD 3.51 and higher

Sun Solaris 9 and higher

Novell Netware 5.0 and higher

Mac OS 9 and higher

DOS 6.2 and higher

Overview

Front View

GCS1228TAA3

GCS1312TAA3

GCS1414TAA3

CAC READER

RESET

CAC

SELECTED

ON LINE

1 21 3 4 54 6 7 8

8-Port Dual View Dual-Link DVI

GCS1228TAA3

3 4 5 6 7 8 9

CAC

SELECTED

ON LINE

2-Port HDMI

GCS1312TAA3

RESET

CAC READER

3 4 5 6 7 8 9

CAC READER

RESET

CAC

READER

CAC

SELECTED

ON LINE

3 4 5 6 7 8 9

Overview

Rear View

GCS1228TAA3

GCS1312TAA3

GCS1414TAA3

CONSOLE

CACCACCACCAC

CPU 1

CPU 2

CPU 3CPU 4

CACCACCACCAC

CPU 5

CPU 6

CPU 7CPU 8

POWER

100-240V~, 1A, 50-60Hz

10 11

12 13

15 16 17 18

CONSOLE

POWE R

CACCAC

CPU 1CPU 2

100-240V~ ,1A , 50-60 Hz

10 11 15 16 17

12 13

POWE R

CACCAC

CPU 1CPU 2

CAC

CPU 3

CAC

CPU 4

100-240V~ ,1A , 50-60 Hz

CONSO LE

10 11

12 13

15 16 17 18

Note:

1. This user manual uses GCS1228TAA3, GCS1312TAA3, and GCS1414TAA3 to demonstrate

each interface (DVI / HDMI / DisplayPort), port number (2 / 4/ 8-Port), and number of displays

(single / dual) included in IOGEAR Secure KVM Switch series.

2. The console video of the GCS1412/GCS1422/GCS1414/GCS1424/GCS1418/GCS1428 (Dis-

playPort models) supports only HDMI video output

3. All IOGEAR Secure KVM Switch PP3.0 models support USB and PS/2 console Keyboard/Mouse

and USB CAC card reader port.

Overview

No. Component Description

1 Port Selection Pushbuttons Pressing a Port Selection Pushbutton brings together the Keyboard, Mouse, Video,

Audio, and CAC reader focus to the computer attached to the corresponding port

2 Port and CAC LEDs

The Port/CAC LEDs located on front panel are to indicate Port/CAC reader selec-

tion or connection status.

Port LEDs (Bottom row; Orange LEDs)

❒ Online – Port LED lights dim orange to indicate that the computer attached

to its corresponding port is connected and powered on

❒ Selected – Port LED lights bright orange to indicate that the computer

attached to its corresponding port has the KVM focus

CAC LEDs (Upper row; Green LEDs)

❒ Online – CAC LED lights dim green to indicate that the computer attached

to its corresponding port has a USB CAC reader cable connection up and

running, and the CAC function is enabled

❒ Selected – CAC LED lights bright green to indicate that the CAC function is

enabled and the computer attached to its corresponding port has the CAC

focus

❒ None – No lights indicate that the cable is not connected or the CAC function

has been disabled

❒ Warning – CAC LED Flashes to indicate that a non-qualied USB Smart

Card/ CAC reader is connected when the corresponding port has the focus

Note:

1. CAC function of each port can be enabled or disabled by pressing the port

selection pushbutton for more than 3 seconds (this is a toggle feature).

Please refer to the Operation section of this user manual for more informa-

tion.

2. All front panel LEDs (except for Power LED) will ash continuously when

a chassis intrusion or self-test failure is detected. See Chassis Intrusion

Detection section for further details

3. Port and CAC LEDs also indicate the status of the Secure KVM self-test.

See Operation section for further details

3 Reset Button

Press the Reset Button to reset IOGEAR Secure KVM Switch

Note:

1. When the Reset Button is pressed for more than 5 seconds, the Keyboard/

Mouse buffer will be purged and KVM switch will reboot and perform a self-

test. After a successful self-test, port focus will be switched to Port 1, and

CAC function of each port will be set to factory default (enabled).

2. If the Secure KVM fails to generate video on the monitor after a reset,

please power off the installation, check the cables, and follow the instruc-

tions in this manual to power on the installation

4 Audio Ports

Connect cables from your speakers to these audio ports

Note:

Only standard analog speaker connections are allowed. The use of analog micro-

phones or line-in audio devices is strictly prohibited

USB Smart Card/CAC

Reader Port

Only qualied USB authentication devices (e.g., standard smart card and CAC

reader) can be connected to this port.

Note:

USB Authentication device lter is congurable by authorized administrators for

trusted authentication devices (e.g. USB token, USB Biometric reader). Please

refer to Administrator’s Guide for details.

6 Num Lock LED

Num Lock LED lights green to indicate that the Num Lock function has been turned

on.

Note:

Num Lock LED on keyboard will be disabled due to security requirement

7 Caps Lock LED

Caps Lock LED lights green to indicate that the Caps Lock function has been

turned on

Note:

Caps Lock LED on keyboard will be disabled due to security requirement

8 Scroll Lock LED

Scroll Lock LED lights green to indicate that the Scroll Lock function has been

turned on.

Note:

Scroll Lock LED on keyboard will be disabled due to security requirement

Overview

9 Power LED Power LED lights blue to indicate that the IOGEAR Secure KVM Switch is powered

10 USB Console Ports

Wired USB keyboard and mouse are connected into these ports. The USB console

keyboard port (lower port) and mouse port (upper port) are only compatible with

standard wired USB keyboards/mice

Note:

1. The console USB keyboard and mouse ports are interchangeable. User

can connect a keyboard to the mouse port and vice versa. However, for

optimal operation, it is recommended that the USB keyboard connected

to the console’s USB keyboard port and the USB mouse connected to the

console’s USB mouse port

2. For security purposes, IOGEAR Secure KVM Switch series do not support

wireless keyboards and mice. Do not attempt to connect a wireless key-

board and mouse to the switch in any case.

3. Non-standard keyboards/mice with integrated USB hubs and/or other

USB-integrated devices may not be fully supported due to the strict security

standards and policy for IOGEAR Secure KVM Switch. If supported, only

basic (HID) keyboard/mouse operations will function

4. Multimedia keys on the keyboard will not function due to security policy

5. Num Lock, Caps Lock, and Scroll Lock LED on keyboards will not function

due to security policy.

11 PS/2 Console Ports Wired PS/2 keyboard and mouse are connected into these ports.

(PS/2 Mouse port: Green; PS/2 Keyboard port: Purple)

12 Video LED(s)

Video LED lights green when the video connection is established.

Video LED ashes when a non-qualied monitor is connected.

Note:

With the Dual View (dual monitor) models, each console video connection has one

Video LED

13 Console Monitor Port(s)

Console monitor’s cables are connected into these ports

Note:

IOGEAR Secure KVM Switch Dual View models has two console monitor ports

14 KVM Port Section Connect IOGEAR proprietary KVM cables from the computers into these ports

15 KVM Audio Ports

Connect audio cable from the connected computers into these ports

Note:

Only speaker connections are allowed. The use of analog microphones or line-in

audio devices is strictly prohibited

16 KVM USB Ports Connect the USB cable from the keyboard and mouse into these ports

17 USB Smart Card / CAC

(Common Access Card)

Reader Port

Connect the USB cable from the connected USB Smart Card / CAC reader into

these ports

18 Power Switch This is a standard rocker switch that powers the IOGEAR Secure KVM Switch off

and on

19 Power Socket Connect the included AC power cord into this socket

Chapter 2 - Hardware Setup

Before You Begin

If the tamper-evident seals are missing or peeled,

avoid using the product and contact your IOGEAR dealer.

If all front panel LEDs (except for Power LED) ash

continuously or the switch’s enclosure appears to be

breached, avoid using this product and contact your

IOGEAR dealer.

Tampering prevention and detection

1. IOGEAR Secure KVM Switch includes tamper-evident tapes to provide visual indications of intru-

sion to the switch’s enclosure. If the tamper-evident seals are missing, peeled, or looks as if they

have been adjusted, avoid using the product and contact your IOGEAR dealer.

2. IOGEAR Secure KVM Switch is equipped with active always-on chassis intrusion detection. If a

mechanical intrusion is detected, the switch will be permanently disabled and all front panel LEDs

(except for Power LED) will ash continuously. If the switch’s enclosure appears to be breached or

all the LEDs are ashing continuously, stop using this product, remove it from service immediately,

and contact your IOGEAR dealer.

3. Any attempt to open the switches enclosure will activate the chassis intrusion detection security,

which will render it inoperable and void the warranty.

4. IOGEAR Secure KVM Switch cannot be upgraded, serviced, or repaired.

5. IOGEAR Secure KVM Switch is equipped with active always-on chassis intrusion detection

security. Never attempt to open the enclosure. Any attempt to open the enclosure will permanently

damage and disable the switch.

6. IOGEAR Secure KVM Switch contains an internal battery which is non-replaceable. Never attempt

to replace the battery or open the switch’s enclosure.

Tamper-evident seal

Always use qualied and authorized peripheral devices

1. For security, IOGEAR Secure KVM Switch supports only standard USB or PS/2 keyboard/mouse

(or pointing device). Do not connect a wireless keyboard/mouse, or keyboard/mouse with an inter-

nal USB hub or composite functions to the switch.

2. When connecting a non-qualied keyboard, the keyboard will not function. No keyboard keystrokes

will be seen on the screen.

3. When connecting a non-qualied mouse, the mouse will not function. No mouse cursor movement

will be seen on the screen.

4. Num Lock LED, Caps Lock LED, and Scroll Lock LED on the keyboard will be disabled due to

security policy.

5. Special multimedia keys on the keyboard will be disabled due to security policy.

6. For security, IOGEAR Secure KVM Switch does not support analog microphones or line-in audio

inputs. Never connect a microphone to the switch’s audio output port, including that of a headset’s.

Only standard analog speakers and headsets are supported.

7. For security, IOGEAR Secure KVM Switch’s USB CAC ports (by default) only support authorized

user authentication devices, such as USB Smartcards or CAC readers. Do not connect other

USB devices to USB CAC Port. Non-qualied or non-authorized USB devices will be rejected. For

administrative conguration, please refer to the Administrator’s Guide and Port Authentication Utility

Guide for details.

Chapter 2 - Hardware Setup

8. For security, do not use any USB CAC authentication device or other peripherals that adopt an

external power source.

9. Always use qualied monitor(s). Non-qualied monitors will be rejected.

10. Do not use wireless video transmitters or any docking device.

11. Do not connect any Thunderbolt device to IOGEAR Secure KVM Switch.

Secure Installation

1. Do not attempt to connect or install the following devices to the computers connected to IOGEAR

Secure KVM Switch:

• TEMPEST computers,

• Telecommunication equipment,

• Frame grabber video cards, or

• Special audio processing cards

2. Important safety information regarding the placement of this device is provided on page 25. Please

review it before proceeding.

3. Before installation, please make sure that the power sources to all connected devices are turned off.

You must unplug the power cords of any computers that have the Keyboard Power On function.

4. Hot-swapping of the console monitor is not allowed. Power off the Secure KVM Switch and the moni-

tor before changing the console monitor.

5. A computer connected to IOGEAR Secure KVM Switch should only be powered on after all of the

device (Video, USB, and audio) are securely connected

Secure Operation and Administration

Please refer to Operation section for detail administrator functions.

Stacking

IOGEAR Secure KVM Switch features a rugged, metal enclosure which provides stability and allows the

unit to be stacked on a desktop. The unit can be placed on any leveled surface that can safely support its

weight and the weight of the attached cables. Please ensure that the surface is clean and free of materi-

als that can block the exhaust vents or otherwise interfere with normal operation of IOGEAR Secure KVM

Switch

Rack-mount

IOGEAR Secure KVM Switch features a rack-mount design and offers rack-mount options. Rack-mount

kits which are specically designed to work with this switch are not supplied in the package and require a

separate purchase.

Cable Connection

To install IOGEAR Secure KVM Switch, please refer to the installation diagram on the following page. The

numbers in the diagrams correspond to the steps below:

1. Connect the wired USB keyboard and USB mouse into the USB console ports located on the unit’s

rear panel. The USB keyboard and mouse console ports are compatible only with standard wired

USB keyboard/mice.

Connect the PS/2 keyboard and PS/2 mouse, if you are using PS/2 keyboard and mouse, into the

corresponding PS/2 ports.

2. Connect the console monitor(s) into the console Video port(s) located on the unit’s rear panel.

Then, power the monitor on.

Chapter 2 - Hardware Setup

Note:

1. The console USB keyboard and mouse ports are interchangeable. You can con-

nect a keyboard to the mouse port and vice versa. However, for optimal operation,

it is recommended that you

connect the USB keyboard to the console’s USB keyboard port and the USB

mouse to the console’s

USB mouse port.

2. For security purposes, IOGEAR Secure KVM Switch does not support wireless

keyboards and mice.

Do not attempt to connect a wireless keyboard/mouse to the switch

3. During IOGEAR Secure KVM Switch operation, non-standard keyboards with inte-

grated USB hubs and/or other USB-integrated devices may not be fully supported,

due to the strict security standards and policy

for IOGEAR Secure KVM Switch. If supported, only basic (HID) keyboard opera-

tions will function

4. When the IOGEAR Secure KVM Switch is powered on and the keyboard or

mouse is rejected, the keyboard and mouse will be inoperable (i.e., mouse cursor

freezes and/or no key strokes response on the connected computer)

4. For Single View (single monitor) IOGEAR Secure KVM Switch

Using IOGEAR’s proprietary KVM cable set (not supplied with this package and must be purchased

separately), connect the Video connector into any available Video socket in the KVM port section of

the switch, then connect the accompanying USB (Keyboard/Mouse or CAC) and speaker connectors

into their corresponding USB and speaker ports.

For Dual View (dual monitors) IOGEAR Secure KVM Switch,

Using IOGEAR’s proprietary KVM cable set (not supplied with this package and must be purchased

separately), connect the Video connector for primary monitor into any available Video socket A in the

KVM port section of the switch, then connect the accompanying USB (Keyboard/Mouse or CAC) and

speaker connectors into their corresponding USB and speaker ports. Connect a separate Video cable

for secondary monitor to corresponding Video socket B in the same KVM port section of the switch.

Chapter 2 - Hardware Setup

Note:

1. When the IOGEAR Secure KVM Switch is powered on, the Video LED lights green

indicating that the video connection is established. The Video LED ashes when

non-qualied monitors are connected

2. Due to security policy, IOGEAR Secure KVM Switch does not support monitor hot-

swap. If you would like to change the console monitor, you must rst power off the

entire installation.

3. Connected monitors will be ltered when IOGEAR Secure KVM Switch is powered

on. Non-qualied monitor will be rejected (Video LED ashes). Please refer to the

LED Display for detail visual identication.

Note:

1. Verify that all connectors are in the same or corresponding KVM Port sockets

(all in Port 1, all in Port 2, etc.). Each socket is marked with appropriate icons

2. If the CAC reader function is to be disabled for certain PCs, it is advised not to

connect the corresponding USB CAC cable in the installation

Note:

1. Only speaker connections are allowed. The use of analog microphones or line-in

audio connections is strictly prohibited.

3. Connect the speakers into the console’s speaker jack located on the unit’s front panel.

Chapter 2 - Hardware Setup

6. Connect the USB Smart Card / CAC reader to the CAC port on the front panel of IOGEAR Secure

KVM Switch

5. With the other end of the KVM cable set, connect the USB, video, and speaker cables into their

respective ports on the computers.

Note:

1. On Dual View (dual display) KVM installation, please verify that the second Video

connection is in the same KVM Port sockets as the rst Video connection (all in

Port 1, all in Port 2, etc.) Each socket is marked with appropriate icons

2. Repeat steps 4, 5, 6, and 7 for each PC system you are installing

3. On Dual View (dual display) KVM installation, you may also connect all of the

primary Video connectors to Video Sockets B and all secondary Video connectors

to Video Sockets A for easier cable connections. Please make sure your console

primary and secondary monitors are connected the same way.

Note:

1. Only qualied USB Authentication devices (e.g., Smart Card and CAC readers

by default) can be connected into this port. During KVM operation, non-qualied or

non-authorized USB devices will be ltered and rejected (CAC LED that has the

port focus will ash continuously). Please refer to LED Display for visual indica-

tions.

2. CDF (Congurable Device Filtering) function can only be operated by authorized

administrators.

3. Please refer to Administrator’s Guide and Port Authentication Utility Guide for

more details

Note:

IOGEAR Secure KVM Switch performs a security self-test at power-on and at each

power cycle. Front panel LEDs will indicate the self-test status and test result. Please

refer to the Operation section and the LED Display section for visual identication

detail.

7. Connect the female end of the power cord into IOGEAR Secure KVM Switch’s power socket. Then,

connect the male end of the power cord into an AC power source.

8. Power on the IOGEAR Secure KVM Switch and check if the LEDs light up. IOGEAR Secure KVM

Switch will begin KVM self-test momentarily.

Page is loading ...

iogear GCS1222TAA3 User manual

Brand: iogear

Model: GCS1222TAA3

Category: KVM switches

Type: User manual

This manual is also suitable for

GCS1324TAA3

Download PDF

report

iogear GCS1222TAA3 User manual

This manual is also suitable for

iogear GCS1222TAA3 User manual

Related papers

Other documents