Crown Audio CE SERIES User manual

Brand: Crown Audio

Model: CE SERIES

Category: Supplementary music equipment

Type: User manual

Operation Manual

CE 1000

Obtaining Other Language Versions:

To obtain information in another language about the use of this product, please contact your

local Crown Distributor. If you need assistance locating your local distributor, please contact Crown at 574-294-8000.

This manual does not include all of the details of design, production, or variations of the equipment. Nor does it cover every possible

situation which may arise during installation, operation or maintenance.

The information provided in this manual was deemed accurate as of the publication date. However, updates to this information may have

occurred.

To obtain the latest version of this manual, please visit the Crown website at www.crownaudio.com.

Trademark Notice:

Crown and Amcron are registered trademarks of Crown International. Other trademarks are the property of their

respective owners.

Some models may be exported under the name Amcron.

125645-8

8/03

CE Series

CE 2000

Operation Manual

CE Series Power Amplifiers

page 2

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install

in accordance with the manufacturer’s instruc-

tions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus that produce heat.

9) Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug

has two blades with one wider than the other.

A grounding-type plug has two blades and a

third grounding prong. The wide blade or the

third prong is provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10) Protect the power cord from being walked on

or pinched, particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11) Only use attachments/accessories specified

by the manufacturer.

12) Use only with a cart, stand, bracket, or table

specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution

when moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms

or when unused for long periods of time.

14) Refer all servicing to qualified service person-

nel. Servicing is required when the apparatus

has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally,

or has been dropped.

15) To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or moisture.

TO PREVENT ELECTRIC SHOCK DO NOT REMOVE

TOP OR BOTTOM COVERS. NO USER SERVICE-

ABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

À PRÉVENIR LE CHOC ÉLECTRIQUE N’ENLEVEZ

PAS LES COUVERCLES. IL N’Y A PAS DES PAR-

TIES SERVICEABLE À L’INTÉRIEUR. TOUS REPA-

RATIONS DOIT ETRE FAIRE PAR PERSONNEL

QUALIFIÉ SEULMENT.

IMPORTANT

CE Series amplifiers require Class 2 output wiring.

MAGNETIC FIELD

CAUTION! Do not locate sensitive high-gain equip-

ment such as preamplifiers or tape decks directly

above or below the unit. Because this amplifier has

a high power density, it has a strong magnetic field

which can induce hum into unshielded devices that

are located nearby. The field is strongest just above

and below the unit.

If an equipment rack is used, we recommend locat-

ing the amplifier(s) in the bottom of the rack and the

preamplifier or other sensitive equipment at the top.

WATCH FOR THESE SYMBOLS:

The lightning bolt triangle is used to alert the user

to the risk of electric shock.

The exclamation point triangle is used to alert the

user to important operating or maintenance instruc-

tions.

Important Safety

Instructions

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for

complicance could void the user’s authority to operate the euqipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

page 3

CE Series Power Amplifiers

Operation Manual

DECLARATION of CONFORMITY

Crown International, Inc.

TCF Technical Certificate No: C975CRI1.ABS

Sue Whitfield

574-294-8289

[email protected]

European Representative's Name and Address:

Nick Owen

19 Clos Nant Coslech

Pontprennau

Cardiff

CF23 8ND United Kingdom

Competent Body’s Name and Address:

Technology International (Europe) Limited

41-42 Shrivenham Hundred Business Park,

Shrivenham, Swindon, Wilts, SN6 8TZ

Equipment Type: Commercial Audio Power Amplifiers

Family Name: CE1000, CE2000, CE2000TX

Model Names: CE1000 Series, CE2000 Series, CE2000TX Series

EMC Standards:

EN 55103-1:1995 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions

EN 55103-1:1995 Magnetic Field Emissions-Annex A @ 10 cm and 1 M

EN 61000-3-2:1995+A14:2000 Limits for Harmonic Current Emissions (equipment input current ≤16A per phase)

EN 61000-3-3:1995 Limitation of Voltage Fluctuations and Flicker in Low-Voltage Supply Systems Rated Current ≤16A

EN 55022:1992 + A1: 1995 & A2:1997 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE: Radiated, Class B Limits; Conducted, Class B

EN 55103-2:1996 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 2: Immunity

EN 61000-4-2:1995 Electrostatic Discharge Immunity (Environment E2-Criteria B, 4k V Contact, 8k V Air Discharge)

EN 61000-4-3:1996 Radiated, Radio-Frequency, Electromagnetic Immunity (Environment E2, criteria A)

EN 61000-4-4:1995 Electrical Fast Transient/Burst Immunity (Criteria B)

EN 61000-4-5:1995 Surge Immunity (Criteria B)

EN 61000-4-6:1996 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields (Criteria A)

EN 61000-4-11:1994 Voltage Dips, Short Interruptions and Voltage Variation

Safety Standard:

EN 60065: 1998 Safety Requirements - Audio Video and Similar Electronic Apparatus

I certify that the product identified above conforms to the requirements of the EMC Council Directive 89/336/EEC as amended by 92/31/EEC, and the Low Voltage Directive 73/23/EES as amended by 93/68/EEC.

Larry Coburn

Signed

Title: Senior Vice President of Manufacturing

Date of Issue: March 28, 2000

Issued By: Crown International, Inc.

1718 W. Mishawaka Road

Elkhart, Indiana 46517 U.S.A.

Technical Construction File Route

Operation Manual

CE Series Power Amplifiers

page 4

Important Safety Instructions .......................................................2

Declaration of Conformity ...........................................................3

1 Welcome .................................................... 5

1.1 Features .........................................................................5

1.2 How to Use This Manual ................................................5

2 Setup ......................................................... 6

2.1 Unpack Your Amplifier ....................................................6

2.2 Install Your Amplifier ......................................................6

2.3 Ensure Proper Cooling ....................................................6

2.4 Choose Input Wire and Connectors .................................7

2.5 Choose Output Wire and Connectors ..............................8

2.6 Wire Your System ...........................................................9

2.6.1 Stereo Mode ...........................................................9

2.6.2 How to Parallel the Inputs .......................................9

2.6.3 Bridge-Mono Mode ................................................10

2.7 Input Sensitivity Switch ...................................................11

2.8 Connect to AC Mains ......................................................11

2.9 Startup Procedure ...........................................................11

3 Operation .................................................... 12

3.1 Precautions .....................................................................12

3.2 Controls, Indicators and Connectors ...............................13

3.3 Front Panel Controls and Indicators ................................14

3.4 Back Panel Controls ........................................................14

4 Advanced Features and Options ......................... 15

4.1 Protection Systems .........................................................15

4.1.1 Bias Servo ..............................................................15

4.1.2 Fault .......................................................................15

4.1.3 Ultrasonic and Radio Frequency Protection ............15

4.1.4 Drive Protection.......................................................15

4.1.5 Compression ..........................................................15

4.1.6 Power Circuit Breaker .............................................15

4.1.7 Proportional-speed Fan ..........................................15

4.2 Advanced Features ..........................................................15

4.2.1 Crown SST Modules ..............................................15

4.2.2 Fault Monitoring .....................................................17

4.3 Options ............................................................................18

4.3.1 Accessories ............................................................18

4.3.2 Alternate Output Connectors ...................................18

4.3.3 Tamper-Resistant Hole Plugs .................................18

4.3.4 Optional 0.775 V Input Sensitivity Setting ..............18

5 Principles of Operation ................................... 19

6 Troubleshooting ............................................ 21

7 Specifications .............................................. 22

8 Service ....................................................... 23

8.1 Worldwide Service ...........................................................23

8.2 US and Canada Service ...................................................23

8.2.1 Service at a US or Canada Service Center ...............23

8.2.2 Factory Service .......................................................23

8.2.3 Factory Service Shipping Instructions ....................23

9 Warranty ..................................................... 24

Crown Factory Service Information Form ....................................27

Table of Contents

page 5

CE Series Power Amplifiers

Operation Manual

1 Welcome

Crown

CE Series amplifiers provide profes-

sional audio amplification for a wide range of

applications, including digital cinema. The

amplifiers are very affordable, and feature front-

panel controls for easy setup and use. They can

be removed for security.

Modern power amplifiers are sophisticated

pieces of engineering capable of producing

extremely high power levels. They must be

treated with respect and correctly installed if

they are to provide the many years of reliable

service for which they were designed.

In addition, CE Series amplifiers include a

number of features which require some expla-

nation before they can be used to their maxi-

mum advantage.

Please take the time to study this manual so

that you can obtain the best possible service

from your amplifier.

1.1 Features

• Accurate, undistorted sound.

• Bridge-mono/stereo mode switch allows

you to set up your amps/speakers in the

configuration that best suits your needs.

• Versatile; handles a wide range of speaker

impedances and outputs.

• Advanced protection circuitry guards

against shorted outputs, open circuits, DC,

mismatched loads, general overheating,

high-frequency overloads and internal

faults.

• Genuine Neutrik

Speakon

connectors.

• Choice of 1/4-inch, XLR or barrier strip

inputs.

• Removable front-panel level control

knobs.

• Selectable input sensitivity.

• Proportional-speed fan optimizes cooling

efficiency.

• Can be mounted in EIA standard 19-in.

(48.3-cm) rack, shallow 14-in. (35.5) rack,

or stacked on top of each other.

• Three Year, No-Fault, Fully-Transferable

Warranty completely protects your invest-

ment and guarantees its specifications.

• Crown’s advance-replacement Profit Pro-

tection Plan provides quick, no-questions-

asked replacement of covered amps.

1.2 How to Use This Manual

This manual provides you with the necessary

information to safely and correctly setup and

operate your amplifier. It does not cover every

aspect of installation, setup or operation that

might occur under every condition. For addi-

tional information, please consult Crown’s

Amplifier Application Guide (available online at

www.crownaudio.com), Crown Technical Sup-

port, your system installer or retailer.

We strongly recommend you read all instruc-

tions, warnings and cautions contained in this

manual. Also, for your protection, please send

in your warranty registration card today. And

save your bill of sale — it’s your official proof

of purchase.

Operation Manual

CE Series Power Amplifiers

page 6

2.1 Unpack Your Amplifier

Please unpack and inspect your amplifier for

any damage that may have occurred during

transit. If damage is found, notify the transpor-

tation company immediately. Only you can ini-

tiate a claim for shipping damage. Crown will

be happy to help as needed. Save the shipping

carton as evidence of damage for the shipper’s

inspection.

We also recommend that you save all packing

materials so you will have them if you ever

need to transport the unit. Never ship the

unit without the factory pack.

YOU WILL NEED (not supplied):

• Input wiring cables

• Output wiring cables

Rack and rack-mounting hardware for mount-

ing amplifier (or a stable surface for stacking)

WARNING: Before you start to set up

your amplifier, make sure you read and

observe the Important Safety Instruc-

tions found at the beginning of this

manual.

2.2 Install Your Amplifier

CAUTION: Before you begin, make sure

your amplifier is disconnected from the

power source, with power switch in the

“off” position and all level controls

turned completely down (counterclock-

wise).

Use a standard 19-inch (48.3 cm) equipment

rack. See Figure 2.1 for amplifier dimensions.

You may also stack amps without using a

cabinet.

NOTE: When transporting, amplifiers should be

supported at both front and back.

2.3 Ensure Proper Cooling

When using an equipment rack, mount units

directly on top of each other. Close any open

spaces in rack with blank panels. DO NOT

block front or rear air vents. The side walls of

the rack should be a minimum of 2 inches (5.1

cm) away from the amplifier sides, and the back

of the rack should be a minimum of 4 inches

(10.2 cm) from the amplifier back panel.

Figure 2.2 illustrates standard amplifier airflow.

2 Setup

Figure 2.1 CE 1000 and CE 2000 Dimensions

Figure 2.2 Airflow

page 7

CE Series Power Amplifiers

Operation Manual

2.4 Choose Input Wire

and Connectors

You have three choices of input connectors:

1/4-inch (6.35-mm) phone, 3-pin XLR, or

barrier strip. You can also use either balanced or

unbalanced wiring.

Figure 2.3 shows balanced connector pin

assignments for XLR and phone. Figure 2.4

shows unbalanced connector pin assignments

for XLR and phone.

Figure 2.5 shows barrier strip input wiring for a

balanced signal. Both channels should be wired

using a common center terminal for ground con-

nection.

NOTE: Custom wiring should only be

performed by qualified personnel.

Figure 2.3 Balanced Input

Connector Wiring

Figure 2.4 Unbalanced Input

Connector Wiring

2 Setup

Figure 2.5 Barrier Strip Input Wiring:

Balanced Signal In

Operation Manual

CE Series Power Amplifiers

page 8

2.5 Choose Output Wire and Con-

nectors

Crown recommends using pre-built or profes-

sionally wired, high-quality, two- or four-con-

ductor, heavy gauge speaker wires. They should

be terminated with Neutrik Speakon NL4FC con-

nectors (Figure 2.6) at one end and appropriate

connectors to fit your speakers at the other end.

If your CE Series amplifier came equipped with

the CEAS1 (barrier strip) or CEAS2 (5-way bind-

ing post) optional output connectors, you may

wire your output to these connectors instead.

Optional output connectors can also be ordered

as a Service Option for installation on existing

CE Series amplifiers.

If the CEAS1 Output Module is installed, use ter-

minal forks or bare wire for your output connec-

tors (see Figure 2.7).

To prevent the possibility of short-cir-

cuits, replace the cover on the barrier

strip after completing the output wiring.

If the CEAS2 Output Module is installed, connect

to it with bare wires, spade lugs or banana plugs

on the speaker cables (Figure 2.8).

Using the guidelines below, select the appropri-

ate size of wire based on the distance from

amplifier to speaker.

CAUTION: Never use shielded cable for

output wiring.

Distance Wire Size

up to 25 ft. 16 gauge

26-40 ft. 14 gauge

41-60 ft. 12 gauge

61-100 ft. 10 gauge

101-150 ft. 8 gauge

151-250 ft. 6 gauge

Figure 2.7 Output Connector Wiring for Stereo

with Optional CEAS1 Output Module.

2 Setup

Figure 2.6 Neutrik

Speakon

Connector

Figure 2.8 Optional CEAS2 5-way Binding Post Output Connector (Left)

Each Pair of Posts Connects to a Dual Banana Plug (Right)

page 9

CE Series Power Amplifiers

Operation Manual

2.6 Wire Your System

2.6.1 Stereo Mode

Make sure the amplifier is turned off and the

level controls are turned down before you wire

the system.

Typical input and output wiring is shown in

Figure 2.9.

INPUTS: Connect input wiring for each channel.

OUTPUTS: Maintain proper polarity (+/–) on

output connectors.

Connect Channel-1 positive (+) speaker load to

Channel-1 positive terminal of amp; repeat for

negative (–). Repeat each channel wiring as for

Channel 1. Refer to Section 3.5 for output con-

nector pin assignments. Make sure the Mode

switch is set to the “Stereo” position when oper-

ating in Stereo mode.

2.6.2 How to Parallel the Inputs

There are three ways to feed the same signal to

each amplifier channel:

1. Buy a "Y" cable. Plug the female end into your

signal cable, and plug the split male ends into

both amplifier inputs.

2. Feed your signal to the Channel-1 input

(either barrier-block or combo). Connect a

jumper wire (Figure 2.10) between the barrier-

block Channel-1 (+) screw terminal and the

Channel-2 (+) screw terminal. Connect another

jumper wire between the Channel-1 (–) screw

terminal and the Channel-2 (–) screw terminal.

3. Feed your signal to the Channel-1 input screw

terminals. Using a mic cable or phone-to-phone

cable, connect Channel-1 combo jack to Chan-

nel-2 combo jack.

See the next page for Bridge-Mono wiring.

2 Setup

Figure 2.9 Typical System Wiring, Stereo Mode

Figure 2.10

Jumper Placement

to Parallel the Inputs

Operation Manual

CE Series Power Amplifiers

page 10

2 Setup

Figure 2.11 Typical System Wiring, Bridge-Mono Mode

2.6.3 Bridge-Mono Mode

Make sure the amplifier is turned off and the

level controls are turned down before you wire

the system.

Typical input and output wiring is shown in

Figure 2.11.

INPUTS: Connect input wiring to CH 1.

OUTPUTS: Connect the speaker across the posi-

tive (+) output terminals. Do not use the negative

(–) terminals when the amplifier is being oper-

ated in Bridge-Mono mode. Refer to Section 2.5

for output connector pin assignments. Make

sure the Mode switch is set to the “Bridge” posi-

tion when operating in Bridge-Mono mode.

NOTE: Turn down (full CCW) the Channel

2 level control when operating the

channel pair in Bridge-Mono mode, as

the Channel 1 level control works both

channels.

NOTE: Crown provides a reference of wiring pin

assignments for commonly used connector

types in the Crown Amplifier Application Guide

available at www.crownaudio.com.

page 11

CE Series Power Amplifiers

Operation Manual

2.8 Connect to AC Mains

Connect your amplifier to the AC mains power

source (power outlet) with the supplied AC power

cordset. First, connect the IEC end of the cordset to

the IEC connector on the amplifier; then, plug the

other end of the cordset to the AC mains.

WARNING: The third prong of this connec-

tor (ground) is an important safety feature.

Do not attempt to disable this ground con-

nection by using an adapter or other meth-

ods.

Amplifiers don’t create energy. The AC mains volt-

age and current must be sufficient to deliver the

power you expect. You must operate your amplifier

from an AC mains power source with not more than

10% variation above or below the amplifier’s speci-

fied line voltage and within the specfied frequency

requirements (indicated on the amplifier’s back

panel label). If you are unsure of the output voltage

of your AC mains, please consult your electrician.

2.9 Startup Procedure

Use the following procedure when first turning on

your amplifier:

1. Turn down the level of your audio source.

2. Turn down the level controls of the amplifier.

3. Turn on the “Power” switch. The Power indicator-

should glow.

4. Turn up the level of your audio source to an opti-

mum level.

5. Turn up the Level controls on the amplifier until

the desired loudness or power level is achieved.

6. Turn down the level of your audio source to its

normal range.

If you ever need to make any wiring or installation

changes, don’t forget to disconnect the power cord.

For help with determining your system’s optimum

gain structure (signal levels) please refer to the

Crown Amplifier Application Guide, available online

at www.crownaudio.com.

2.7 Input Sensitivity Switch

A two-position Input Sensitivity switch is located

on the back panel near the input connectors

(Figure 2.12). Your amplifier is shipped from the

factory with this switch set to the 1.4V position.

At this setting, a 1.4V input signal will drive the

amplifier to full power into an 8-ohm load when

the level controls are turned to maximum. This

setting works best when the amplifier is being

driven by equipment with a +4 dBu output — an

output level at which most professional equip-

ment operates.

If required, the Input Sensitivity switch can be

moved to the 26-dB position, so that the ampli-

fier provides a fixed voltage gain of 20 (or 26 dB:

1 volt in, 20 volts out). This setting works best

with output levels of +10 dBu (2.5 volts RMS) or

more. Some brands of DJ mixers, in particular,

have output levels in this range.

Selecting the correct sensitivity will allow your

equipment to operate at its optimum level and

improve the signal-to-noise of the system.

Make sure the amplifier is turned off and

the level controls are turned down before

you change the switch setting.

Figure 2.12 Location of Input Sensitivity Switch

2 Setup

Sensitivity Switch

Operation Manual

CE Series Power Amplifiers

page 12

3.1 Precautions

Your amplifier is protected from internal and exter-

nal faults, but you should still take the following

precautions for optimum performance and safety:

1. Before use, your amplifier first must be config-

ured for proper operation, including input and

output wiring hookup. Improper wiring can

result in serious operating difficulties. For

information on wiring and configuration, please

consult the Setup section of this manual or, for

advanced setup techniques, consult Crown’s

Amplifier Application Guide available online at

www.crownaudio.com.

2. Use care when making connections, selecting

signal sources and controlling the output level.

The load you save may be your own!

3. Do not short the ground lead of an output cable

to the input signal ground. This may form a

ground loop and cause oscillations.

3 Operation

4. WARNING: Never connect the output to

a power supply, battery or power main.

Electrical shock may result.

5. Tampering with the circuitry, or making unau-

thorized circuit changes may be hazardous and

invalidates all agency listings.

6. Do not operate the amplifier with the red Clip

LEDs constantly flashing.

7. Do not overdrive the mixer, which will cause

clipped signal to be sent to the amplifier. Such

signals will be reproduced with extreme accu-

racy, and loudspeaker damage may result.

8. Do not operate the amplifier with less than the

rated load impedance. Due to the amplifier’s

output protection, such a configuration may

result in premature clipping and speaker dam-

age.

Remember: Crown is not liable for damage that

results from overdriving other system components.

page 13

CE Series Power Amplifiers

Operation Manual

Figure 3.1

Controls,

Indicators &

Connectors

3 Operation

3.2 Controls, Indicators and Connectors

Operation Manual

CE Series Power Amplifiers

page 14

3 Operation

3.4 Back Panel Controls and

Connectors

Input Sensitivity Switch

This two-position Input Sensitivity switch is located

near the input connectors. It lets you select between

1.4 V input sensitivity or 26 dB gain. Please see

Section 2.7 in this manual for details.

Mode Switch

This two-position switch selects either Stereo or

Bridge-Mono mode of operation. Stereo mode pro-

vides identical power output to each of the two

amplifier output channels. Bridge-Mono mode

combines the two amplifier output channels into a

single mono channel with twice the voltage of a sin-

gle stereo channel.

Do NOT select Bridge-Mono mode without

first making sure the amplifier has been

wired in a Bridge-Mono configuration. For

more information on wiring for Bridge-Mono mode,

see Section 2.6.2.

Fault Jack

This is an RJ-11 jack (which looks like a telephone

jack). By attaching a signaling device to the Fault

jack, you can monitor the amplifier’s Fault status

from a remote location. See Section 4.2.2 for more

information on fault monitoring.

Barrier Block Inputs

For each channel, this row of screw terminals pro-

vides a balanced input, which is in parallel with the

channel’s Combo input connector.

Neutrik Combo Input

One per channel, this combination 1/4-inch phone

jack and XLR connector provides a balanced or

unbalanced input.

Neutrik Speakon

Output

One per channel, this Neutrik Speakon

connector

with four terminals connects to loudspeakers.

See Section 4.2.2 in this manual for more informa-

tion on fault monitoring and suggestions for signal-

ling device circuity.

Some fault conditions may cause the output of the

amplifier to be muted.

Clip Indicators

These are two red LEDs (one per channel). The Clip

Indicator turns on when distortion is audible in the

amplifier output.

Signal Indicators

These are two green LEDs (one per channel). The

Signal Indicator illuminates when a signal (> –40

dBm) is present at the INPUT of the amplifier for

that channel. Because these indicators receive the

signal before the level controls, they can be used to

troubleshoot wiring problems within a system. If the

Signal indicator for a channel is not lit, no signal is

reaching the amplifier on that channel.

Power Indicator

The green Power indicator lights when your CE-

Series amp has been turned on and has power.

Level Controls

Two rotary detented Level controls (one for each

channel) are are used to adjust each channel’s out-

put.

If you wish, the level control knobs may be pulled

from the front panel and the holes plugged with the

supplied caps to minimize tampering of control set-

tings.

3.3 Front Panel Controls and

Indicators

Power Switch

The power switch turns the amplifier on (“I”) or off

(“O”).

Note that dangerous voltages may still be

present in the amplifier even when the

power switch is in the off (“O”) position.

Before moving the amplifier or making any wiring or

installation changes, it is important to also discon-

nect the power cord from the amplifier or power

source.

Reset Switch

The push-button reset switch is used to reset the

circuit breaker that protects the power supply.

Fault Indicators

Two red LEDs (one for each channel) are located on

the front panel. The Fault Indicators are normally

OFF, but will blink under five different conditions:

1. When the amplifier is first powered up, until the

unit is ready for operation.

2. If the heatsinks reach a temperature above normal

working limits.

3. If the transformer thermal protection circuit is

activated.

4. If the amplifier output wires develop a short-cir-

cuit.

5. If the amplifier output stage stops operating.

The fault status of the amplifier can also be moni-

tored remotely by attaching a signalling device to

the Fault jack located on the amplifier back panel.

page 15

CE Series Power Amplifiers

Operation Manual

NOTE: For detailed information about

these Crown amplifier features, please

consult the Crown Amplifier Application

Guide, available on the Crown website

at www.crownaudio.com.

4.1 Protection Systems

CE Series amplifiers are protected against

shorted, open or mismatched loads; over-

loaded power supplies; excessive temperature;

chain destruction phenomena; input overload

damage; and high-frequency blowups. They

also protect loudspeakers from input/output

DC, large or dangerous DC offsets and turn-on/

turn-off transients.

4.1.1 Bias Servo

Bias servo translates the output heatsink tem-

perature to controlled bias current. This pre-

vents thermal runaway and holds the amplifier’s

notch distortion to a minimum.

4.1.2 Fault

The amplifier will light the Fault LED on the

front panel if the amplifier output stage stops

operating. If this happens, take the unit to an

authorized Crown Service Center.

4.1.3 Ultrasonic and Radio Fre-

quency Protection

An amplifier's slew rate only needs to be large

enough to deliver the maximum voltage at the

highest required frequency. Higher slew rates

actually let the amplifier reproduce undesirable

frequencies. By design, the CE Series amplifi-

ers have a controlled slew rate to put a fre-

quency limit on the highest frequencies that

they reproduce. This limit occurs well above 20

kHz, so there is no audible effect on perfor-

mance.

This approach protects the amplifier from radio

frequencies and can even protect some sensi-

tive loads (including some tweeters).

4.1.4 Drive Protection

This system temporarily removes output drive

to protect the amplifier and its loads. Drive pro-

tection can be activated in two situations. First,

if dangerous subsonic frequencies or direct

current (DC) is detected in the amplifier's out-

put, drive protection will activate. The amplifier

resumes normal operation when it no longer

detects dangerous output. Activating this pro-

tection is very unlikely, but improper source

signals like infrasonic square waves or a

severely clipped input signal can activate this

system.

Second, the amplifier's fault protection system

puts the affected channel into drive protection

mode in rare situations where heavy common-

mode current is detected in its output. The

amplifier should never output heavy common-

mode current unless its circuitry is damaged.

Activating drive protection helps prevent further

damage.

4.1.5 Compression

A full-time compressor is in-line with the sig-

nal, reducing the risk of damage to your speak-

ers.

4.1.6 Power Circuit Breaker

A front panel push button is used to reset the

circuit breaker that protects the power supply.

4.1.7 Proportional-speed Fan

The speed of the cooling fan is controlled by

the transformer temperature and the heatsink

temperature.

4.2 Advanced Features

4.2.1 Crown SST Modules

Crown optional SST (System Solution Topolo-

gies) modules were specially designed to

improve the fidelity and versatility of your audio

system. They feature a variety of professional

signal routing and filtering capabilities, with

active crossovers that allow the audio signal to

be split and sent to auxiliary amplifiers. Your

amplifier may have come with an SST module

already factory-installed, or your choice of SST

modules can be easily added to the amplifier by

any authorized Crown Service Center.

For information on wiring and configuration of

amplifiers equipped with an optional Crown

SST crossover module, please refer to the SST

Crossover Reference Manual included in your

literature package.

Refer to the following descriptions for an over-

view of available Crown SST crossover mod-

ules. Crown plans to release additional

accessory plug-in modules offering a range of

advanced features and capabilities. Watch for

new releases:

SST-MX Crossover

Features include:

• Stereo biamp.

• 100-Hz fixed crossover with 24-dB/octave

Linkwitz-Riley tuned filters.

•Neutrik

Combo 1/4-inch (6.35-mm) and

XLR input jacks.

• Barrier block balanced outputs.

• Optional high-pass filter bypass on ampli-

fied outputs adapts system for full-range

use.

SST-SX Crossover

Features include:

Mono-summed sub-bass output for biamp

operation of subs.

• 24-dB/octave Linkwitz-Riley tuned filters.

• Crossover switchable between 80 and 120

Hz.

•Neutrik

Combo 1/4-inch (6.35-mm) and

XLR input jacks.

• Male 3-pin XLR outputs.

Optional high-pass filter bypass on amplified

output adapts system for full-range use.

4 Advanced Features

and Options

Operation Manual

CE Series Power Amplifiers

page 16

SST-SBSC (Summed Bass Stereo

Crossover) Module

See Figure 4.1. Features include:

• Stereo biamp.

• Ten user-specified crossover frequencies.

• 12-, 18- and 24-dB/octave

(Linkwitz-Riley) filters.

• CD horn equalization.

• Mono summing of sub-bass output for

driving subs.

SST-SBSC-3632T

This is a custom three-channel crossover net-

work with CD-horn equalization and summed

low-frequency output specifically designed for

use with JBL

model 3632T ScreenArray

cinema speaker systems installed in cinemas,

studio production and post-production envi-

ronments.

Features:

• High-frequency signals are internally

routed to the channel-one amplifier input,

and mid-frequency signals are routed to

the channel-two amplifier input.

• Mono summing of low-frequency signals

are routed from Output B to an external

amplifier.

•Neutrik

Combo jacks for balanced input

connection.

• Removable barrier block connectors for

balanced output to other components.

SST-SBSC 4632T

Like the SST-SBSC 3632T but for the JBL

4632T cinema speakers.

SST-4622

See Figure 4.2. This is a custom two-channel

crossover network with equalization specifically

designed for use with JBL

model 4622

ScreenArray

cinema speaker systems

installed in cinemas, studio production and

post-production environments.

Features include:

• Low-frequency signals are internally

routed to the channel-1 amplifier input,

and high-frequency signals are routed to

the channel-2 amplifier input.

• Barrier block connectors for balanced sig-

nal input.

SST-3632

Like the SST-4622 but for the JBL 3632 cinema

speaker systems.

Additional features include:

• Time correction via an all-pass analog

delay ensures coherent summation

through the crossover region, while main-

taining optimal vertical polar response.

SST-4632

Like the SST-3632 but for the JBL 4632 cinema

speaker systems.

Figure 4.1 SST-SBSC

Crossover Network

Figure 4.2 SST-4622

Crossover Network

4 Advanced Features

and Options

page 17

CE Series Power Amplifiers

Operation Manual

4.2.2 Fault Monitoring

The Fault (RJ-11) jack, which looks like a telephone

jack, is located on the back of your CE Series ampli-

fier (Figure 4.3). It gives you an easy way to

remotely monitor the amplifier’s fault status. To set

up a circuit that will cause an LED to light whenever

a fault status occurs, you can simply use the sug-

gested circuit shown in Figure 4.4.

When using this circuit, the LED will glow under

any of these conditions:

• The amplifier has just been turned on and is still

in the 4-second turn-on delay.

• The heatsinks are too hot.

•The transformer thermal protection is activated.

• The amplifier output wires have developed a short

circuit.

• The limiter has been overdriven by > 6 dB for a

long time.

• The amplifier output stage has stopped operating.

Refer the unit to an authorized Crown Service Cen-

ter.

• The amplifier is turned off.

If you choose to design your own circuit to interface

this signal to your system, note that this RJ jack is

polarity sensitive. Pin 2 must be grounded, and Pin

5 must be supplied with a positive voltage pull-up

(positive with respect to ground). Refer to Figure 4.5

for RJ jack pin assignments. The maximum signal

that can be exposed to the Fault jack is 35VDC and

10 mA. Best results are obtained with 10 mA LEDs.

The mating connector for the CE Series TX RJ-11

jack contains 4 contact pins in a 6-slot case, as

shown. For additional information please contact

your local dealer or Crown Technical Support.

Figure 4.4 Fault Status LED Circuitry

Figure 4.5 RJ-11 Jack Wiring and Pin Assignments

4 Advanced Features

and Options

Figure 4.3 Location of Fault Jack

Operation Manual

CE Series Power Amplifiers

page 18

4.3.3 Tamper-Resistant Hole Plugs

Your CE Series amplifier comes with a set of

tamper-resistant hole plugs, which allow you to

“protect” the level controls against unauthorized

adjustment. To use, simply pull off the control

knobs from the front of the amp, and slip the hole

plugs into place (see Figure 4.8). The plugs should

press easily into position with light force. Once in

place, the plugs will help to avoid most accidental

or intentional tampering (some situations may

require additional security measures).

To remove the hole plugs, simply pry the plug away

from the amplifier case using a small, flat-blade

screwdriver. To help to ensure adequate security, the

plugs have been designed to be more difficult to

remove than to place into position. If necessary,

additional hole plugs can be purchased separately

from Crown’s Parts Department (Part # 103234-1).

Store your knobs in a safe location should you need

to make level adjustments in the future.

4.3.4 Optional 0.775 V Input

Sensitivity Setting

The CE Series amplifier also provides an optional

0.775 V input sensitivity setting. If you determine

that your application requires this sensitivity set-

ting, please contact Crown Technical Support for

more information.

4 Advanced Features

and Options

Figure 4.6 Model CEAS1 Barrier Block

Output Connectors

Figure 4.7 Model CEAS2 5-way

Binding Post Output Connectors

Figure 4.8 Tamper-Resistant Hole Plugs

Installed in a CE Series Amplifier

4.3 Options

4.3.1 Accessories

CE HANDLES

Handles complement your amplifier’s appearance,

aid in transportation, and facilitate rack mounting

and removal. They are available from Crown’s Sales

Department; just ask for “CE Handles.”

CE-S1

Speakon to barrier output adapter. Compatible with

CE versions CE 1000 and CE 2000 amplifiers (ini-

tial release).

CE-S2

Speakon to 5-way binding post adapter.Compatible

with CE versions CE 1000 and CE 2000 amplifiers

(initial release).

4.3.2 Alternate Output Connectors

For added system flexibility, Crown offers optional

secondary output connectors that are compatible

with the current CE versions: CE 1000A , CE 2000A,

CE 1000B and CE 2000B amplifiers. (These model

numbers are printed only on the serial number

label.)

You have a choice of either the CEAS1 barrier block

(see Figure 4.6) or the CEAS2 5-way binding post

connectors (see Figure 4.7). Alternate output con-

nectors may come factory installed on new amplifier

orders. They can also be added to existing CE

Series amplifiers by an authorized Crown Service

Center. For more information, please contact Crown

Technical Support.

page 19

CE Series Power Amplifiers

Operation Manual

For the sake of simplicity, only channel one of

the amplifier is described.

Signal is presented to the CE amplifier through

one of three connectors when using the stan-

dard input module. Each channel is outfitted

with a balanced XLR/phone jack and a barrier

strip. These connectors are wired in parallel,

which allows daisy chaining when needed. The

signal is then converted from balanced to

unbalanced in the Balanced Input Stage where

it also receives RFI protection. Signal then

flows into the Variable Gain Stage where the

front panel level controls are allowed to affect

the gain.

Following this stage, the signal is put under the

control of a full-time compressor circuit com-

prised of a symmetrical window detector, a

buffer amplifier, and the gating op amp which

uses several small components to set the com-

pressor’s attack and decay characteristics. The

actual compressing is accomplished by an

opto-isolator which affects the gain in the sig-

nal path.

Next the signal enters the error amplifier circuit,

where it is mixed with a small portion of the

output signal in such a way as to control the

amplifier’s overall output perfomance.

Following the error amp is the LVA stage, which

is where the low-voltage referenced signal gets

translated to the output high-voltage rails. The

last voltage amplifier, in conjunction with a

bootstrap current source, drives both predriv-

ers and the bias servo. The bias servo is

mounted in such a way as to translate the out-

put heatsink temperature into a controlled bias

current to prevent thermal runaway and hold

the amplifier’s notch distortion to a minimum.

The predrivers provide enough signal to acti-

vate the drivers, which together operate in the

class AB range. For the major output current

requirements, the drivers feed the various num-

bers of paralleled output transistors which

operate in a class B mode. This we call the Tri-

ple-Deep Darlington Output Stages.

The output transistors are protected by the Time

Dependent Voltage & Current circuit. This cir-

cuit protects the devices from extending

beyond their safe area of operation, but allows

the devices to provide high bursts of peak

power with music, allowing your amplifier to

deliver more punch. This amplifier output

topology offers a good combination of low qui-

escent amplifier heating, great distortion per-

formance at high powers, and relative

simplicity, with impressive reliability and value.

All output power is delivered through 4-circuit

Speakon

connectors. These connectors have

been wired in such a way as to allow you the

most versatility. The Channel 1 and 2 connec-

tors are cross wired so you can cover all

options, from dual cable stereo (typical), to

Bridge-Mono in one connector, to running a bi-

amp speaker with one amplifier and one cable

per speaker cabinet.

The output relay, in conjunction with input sig-

nal mute circuit, assures the amplifier will be

well-behaved during turn on and off. In the

event of an amplifier output failure, a triac will

activate to turn off the offending channel and

protect your speakers.

The turn on delay circuit functions to keep the

output relay open until all the voltages are up

and stable, both in the amplifier, and in all the

components in the system ahead of the

amplifier.

Heatsink temperature is monitored by a thermal

probe attached to the heatsink. As the tempera-

ture rises, the probe sends a proportional cur-

rent to the proportional speed fan circuit which

starts the fan. Should the power transformer

reach its maximum safe temperature, an inter-

nal thermal switch opens and the fan circuit

turns on full speed to quickly cool down the

amplifier. It also disconnects the load via the

output relay, removing any output current and

further speeding a cool-down cycle. Extra care

was taken during the design stage to set this

point both to protect your investment and to

guard against nuisance tripping.

Whenever the heatsinks or the transformer

reach a maximum temperature, or during the

normal turn-on delay window, the front panel

Fault LEDs will blink to get your attention.

A modular jack is mounted on the back panel

(same type as used on telephones). Pins 2 and

5 are connected to an opto-isolator which is

always in a low-resistance state whenever the

unit is on and functional. Should a fault be

detected or should the amplifier lose AC power,

the opto-isolator will change to a high resis-

tance, allowing the user to remotely detect the

status of the amplifier.

The Signal Presence Indicators tap the signal

chain just before the level controls and prior to

the power amplifier chain. They are not ampli-

fier output indicators and should only be used

to indicate the presence of signal to the ampli-

fier front end.

The Clip light is driven from the output of the

compressor circuitry and lights to indicate the

onset of audible distortion.

The Power LED is driven from the low-voltage

supply.

A positive and negative regulator form the ±15-

volt power supplies. Add to that the main trans-

former, a full-wave bridge rectifier, and high

energy electrolytic to form the main power sup-

ply. They are protected by the front-panel line

circuit breaker and controlled by the front-panel

power switch.

5 Principles of Operation

Operation Manual

CE Series Power Amplifiers

page 20

5 Principles of Operation

Figure 5.1

CE Series

Amplifier Block

Diagram

(Shown with

Standard Input

Module)

TRANSLATOR LVA

BIAS

CURRENT

SOURCE

BALANCE

INPUT STAGE

VARIABLE

GAIN STAGE

ERROR

AMP

BALANCED

INPUTS

TO SIGNAL

PRESENCE

INDICATOR

COMPRESSOR

CONTROL

TO CLIP

INDICATOR

BUFFER

MUTE

DC PROTECT

LOGIC

FAULT

CONNECTOR

–VCC

+ HI-VOLTAGE

BOOTSTRAP

BIASBIASBIASBIASBIAS

TDVI

LIMITER

TRIPLE-DEEP

DARLINGTON

NPN POSITIVE

OUTPUT STAGE

TRIPLE-DEEP

DARLINGTON

NPN NEGATIVE

OUTPUT STAGE

PROPORTIONAL

SPEED

FAN

CONTROL

FAN

PROTECT

HEATSINK

TEMPERATURE

OUTPUT

CONTROL

HEATSINK

TEMPERATURE

TRANSFORMER

TEMPERATURE

TO FAULT

INDICATOR

POWER

SUPPLY

+ VCC

+ 15V

– 15V

– VCC

TURN-ON

DELAY

OUTPUT

BOOTSTRAP

CIRCUIT

+ HI-VOLTAGE

BOOTSTRAP

Page is loading ...

Crown Audio CE SERIES User manual

Brand: Crown Audio

Model: CE SERIES

Category: Supplementary music equipment

Type: User manual

Download PDF

report

Crown Audio CE SERIES User manual

Crown Audio CE SERIES User manual

Related papers

Other documents