Compaq 5500R - ProLiant - 256 MB RAM Specification

ProLiant 5500 and 5500R

Maintenance and Service Guide

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

Second Edition (March 1999)

Compaq Computer Corporation

Part Number 328692-002

Spare Part Number 328704-002

Notice

The information in this publication is subject to change without notice.

COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR

EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE

OF THIS MATERIAL. THIS INFORMATION IS PROVIDED “AS IS” AND COMPAQ COMPUTER

CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED OR STATUTORY AND

EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR

PARTICULAR PURPOSE, GOOD TITLE AND AGAINST INFRINGEMENT.

This publication contains information protected by copyright. No part of this publication may be

photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation.

The software described in this guide is furnished under a license agreement or nondisclosure agreement.

The software may be used or copied only in accordance with the terms of the agreement.

Compaq, Deskpro, Fastart, Compaq Insight Manager, Systempro, Systempro/LT, ProLiant, ROMPaq,

QVision, SmartStart, NetFlex, QuickFind, PaqFax, ProSignia, registered United States Patent and

Trademark Office.

Neoserver, Netelligent, Systempro/XL, SoftPaq, QuickBlank, QuickLock are trademarks and/or service

marks of Compaq Computer Corporation.

Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation.

Pentium is a registered trademark and Xeon is a trademark of Intel Corporation.

Other product names mentioned herein may be trademarks and/or registered trademarks of their respective

companies.

Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

Maintenance and Service Guide

Second Edition (March 1999)

Part Number 328692-002

Spare Part Number 328704-002

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

Contents

About This Guide

Symbols in Text.........................................................................................................vii

Compaq Technician Notes .......................................................................................viii

Where to Go for Additional Help.............................................................................viii

Integrated Management Display .......................................................................viii

Telephone Numbers ............................................................................................ix

Chapter 1

Illustrated Parts Catalog

Mechanical Parts Exploded View (Tower Model) ...................................................1-1

System Components Exploded View (Tower Model)..............................................1-3

Spare Part List ..........................................................................................................1-4

Chapter 2

Removal and Replacement Procedures

Electrostatic Discharge Information.........................................................................2-1

Symbols in Equipment .............................................................................................2-2

Preparation Procedures.............................................................................................2-3

Rack Warnings..................................................................................................2-4

Server Warnings and Precautions......................................................................2-5

Caster Mounting Plate (Tower)................................................................................2-6

Front Bezel Door (Tower)........................................................................................2-7

Fixed Front Bezel.....................................................................................................2-8

Side Access Panel.....................................................................................................2-9

Top Access Panel ...................................................................................................2-10

U-Channel Access Panel ........................................................................................2-11

Fans ........................................................................................................................2-12

Media Storage.........................................................................................................2-14

Drive Cage Assembly......................................................................................2-16

Hot-Plug Hard Drives......................................................................................2-17

Removable Media ...........................................................................................2-19

1.44-MB Diskette Drive..................................................................................2-20

SCSI and CD-ROM Cable Connection Diagram ...................................................2-21

Integrated Management Display (IMD) .................................................................2-23

Power Switch with LED.........................................................................................2-25

Processor, Processor Power Module, and Terminator Board Locations.................2-26

Processor Removal.................................................................................................2-27

Processor Power Module........................................................................................2-28

Processor Terminator Modules...............................................................................2-29

iv Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

Removal and Replacement Procedures

continued

Peripheral Board.....................................................................................................2-30

Memory..................................................................................................................2-32

Memory Board ................................................................................................2-34

Dual Inline Memory Modules (DIMMs).........................................................2-35

64-bit Dual Channel Wide Ultra2 SCSI Adapter ...................................................2-36

Network Interface Controller (NIC).......................................................................2-37

Hot-Plug Power Supply LED Indicators ................................................................2-38

Hot-Plug Power Supply Cover Plate ......................................................................2-40

Power Backplane Board .........................................................................................2-41

System I/O Board with Tray...................................................................................2-42

External Replacement Battery................................................................................2-43

Chapter 3

Diagnostic Tools

Diagnostic Tools Utility Overview...........................................................................3-2

Default Configuration...............................................................................................3-4

Default Configuration Messages.......................................................................3-4

Inspect Utility....................................................................................................3-4

Utilities Access.........................................................................................................3-5

Running Compaq Utilities.................................................................................3-5

Power-On Self-Test (POST).....................................................................................3-7

POST Error Messages.......................................................................................3-7

Diagnostics Software..............................................................................................3-21

Steps for Diagnostics.......................................................................................3-21

100 – 199, Primary Processor Test Error Codes .............................................3-22

200 – 299, Memory Test Error Codes.............................................................3-23

300 – 399, Keyboard Test Error Codes...........................................................3-24

400 – 499, Parallel Printer Test Error Codes...................................................3-24

500 – 599, Video Display Unit Test Error Codes............................................3-25

600 – 699, Diskette Drive Test Error Codes ...................................................3-26

800 – 899, Monochrome Video Board Test Error Codes................................3-27

1100 – 1199, Serial Test Error Codes .............................................................3-27

1200 – 1299, Modem Communications Test Error Codes..............................3-28

1700 – 1799, Hard Drive Test Error Codes.....................................................3-29

1900 – 1999, Tape Drive Test Error Codes.....................................................3-30

2400 – 2499, Advanced VGA Board Test Error Codes ..................................3-30

6000 – 6099, Compaq Network Interface Controller Boards

Test Error Codes..............................................................................................3-32

6500 – 6599, SCSI Hard drive Test Error Codes ............................................3-33

6600 – 6699, SCSI/IDE CD-ROM Drive Test Error Codes............................3-33

6700 – 6799, SCSI Tape Drive Test Error Codes ...........................................3-34

7000 – 7099, Server Manager/R Board Test Error Codes...............................3-34

8600 – 8699, Pointing Device Interface Test Error Codes..............................3-35

Array Diagnostic Utility (ADU).............................................................................3-36

Starting ADU ..................................................................................................3-36

Integrated Management Log...................................................................................3-47

Multiple Ways of Viewing the Log.................................................................3-47

Event List ........................................................................................................3-49

Event Messages...............................................................................................3-49

About This Guide v

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

Diagnostic Tools

continued

Rapid Error Recovery.............................................................................................3-51

Automatic Server Recovery-2.........................................................................3-51

Server Health Logs..........................................................................................3-61

ASR-2 Integrated Management Log Messages...............................................3-61

Storage Fault Recovery Tracking....................................................................3-64

Storage Automatic Reconstruction..................................................................3-64

Network Interface Fault Recovery Tracking...................................................3-64

Memory Fault Recovery Tracking ..................................................................3-64

Remote Service Features........................................................................................3-65

ROMPaq Error Recovery Options..........................................................................3-65

ROMPaq Disaster Recovery ...........................................................................3-66

Compaq Insight Manager .......................................................................................3-67

Features of Compaq Insight Management.......................................................3-67

Compaq Insight Management Software Architecture .....................................3-68

Chapter 4

Connectors, Switches, LEDs, and Jumpers

Ultra2 Backplane Board Connectors ........................................................................4-2

Rear Connectors .......................................................................................................4-3

System I/O Board Components................................................................................4-4

System Board Core Frequency Switch.....................................................................4-5

Peripheral Board Components..................................................................................4-6

Peripheral Board Configuration Switches ................................................................4-7

System Board Interlock LED Indicators ..................................................................4-8

Chapter 5

Physical and Operating Specifications

System Unit..............................................................................................................5-2

Dual Inline Memory Modules (DIMMs)..................................................................5-3

1.44-MB Diskette Drive...........................................................................................5-3

24X or Greater IDE CD-ROM Drive .......................................................................5-4

Integrated Dual-Channel Wide Ultra SCSI Controller.............................................5-6

64-bit Dual Channel Wide Ultra2 SCSI Adapter .....................................................5-6

Smart Array 3200 Controller....................................................................................5-7

Compaq 10/100 TX PCI Intel UTP Controller (NIC) ..............................................5-8

Compaq 10/100 TX PCI UTP Controller (NIC).......................................................5-8

Non-Hot-Plug Ultra2 Hard Drives ...........................................................................5-9

Non-Hot-Plug Wide-Ultra Hard Drives .................................................................5-10

Hot Plug Ultra2 Hard Drives..................................................................................5-11

Hot-Plug Wide-Ultra Hard Drives..........................................................................5-12

Index

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

About This Guide

This Maintenance and Service Guide is a troubleshooting guide that can be used for reference

when servicing ProLiant 5500 and 5500R Servers.

WARNING: To reduce the risk of personal injury from electrical shock and hazardous energy

levels, only authorized service technicians should attempt to repair this equipment. Improper

repairs could create conditions that are hazardous.

xx - xx kg

xx - xx lb

WARNING: Any product or assembly marked with these symbols indicates that the

component exceeds the recommended weight for one individual to handle safely.

To reduce the risk of personal injury or damage to the equipment, observe local

Occupational Safety requirements and guidelines for heavy equipment handling.

WARNING: To reduce the risk of personal injury from electrical shock, the installation of

options and servicing of this product must be performed by individuals who are knowledgeable

of the procedures, precautions, and hazards associated with equipment containing hazardous

energy circuits.

Symbols in Text

These symbols may be found in the text of this guide. They have the following meanings:

WARNING: Text set off in this manner indicates that failure to follow directions in the warning

could result in bodily harm or loss of life.

CAUTION: Text set off in this manner indicates that failure to follow directions could result in

damage to equipment or loss of information.

IMPORTANT: Text set off in this manner presents clarifying information or specific instructions.

NOTE: Text set off in this manner presents commentary, sidelights, or interesting points of information.

viii Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

Compaq Technician Notes

WARNING: Only authorized technicians trained by Compaq should attempt to repair this

equipment. All troubleshooting and repair procedures are detailed to allow only

subassembly/module level repair. Because of the complexity of the individual boards and

subassemblies, no one should attempt to make repairs at the component level or to make

modifications to any printed wiring board. Improper repairs can create a safety hazard.

WARNING: To reduce the risk of personal injury from electric shock or damage to the

equipment:

■ If the system has multiple power supplies, disconnect power from the system by

unplugging all power cords from the power supplies.

■ Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

■ Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

CAUTION: To properly ventilate your system, you must provide at least 12 inches (30.5 cm) of

clearance at the front and back of the computer.

CAUTION: The computer is designed to be electrically grounded. To ensure proper operation,

plug the AC power cord into a properly grounded AC outlet only.

Where to Go for Additional Help

In addition to this guide, the following information sources are available:

■ User Documentation

■ Compaq Service Quick Reference Guide

■ Service Training Guides

■ Compaq Service Advisories and Bulletins

■ Compaq QuickFind

■ Compaq Insight Manager

■ Compaq Download Facility: Call 1-281-518-1418

Integrated Management Display

Some Compaq server models include a Compaq Integrated Management Display (IMD), an

integrated, 16x4 character display mounted on the front of the server. This display provides

easy-to-use menu-driven access to server information, including model number, LCD firmware

revision, and POST operations.

About This Guide ix

For use with Pentium II Xeon and Pentium III Xeon processor-based servers only

Telephone Numbers

For the name of your nearest Compaq Authorized Reseller:

■ In the United States, call 1-800-345-1518

■ In Canada, call 1-800-263-5868

For Compaq technical support:

■ In the United States and Canada, call 1-800-386-2172

■ For Compaq technical support phone numbers outside the United States and Canada, visit

the Compaq website at:

http://www.compaq.com

For use with Pentium II and Pentium III Xeon processor-based servers only

Chapter 1

Illustrated Parts Catalog

Mechanical Parts Exploded View (Tower Model)

This chapter provides the illustrated parts breakdown and a spare parts list for Compaq

ProLiant 5500 and 5500R Servers. See Table 1-1 for the names of referenced spare parts.

1-2 Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II and Pentium III Xeon processor-based servers only

6a

6c

6b

27b

27a

1

3

2

4

5

32

7b

31

Figure 1-1. Exploded view, Compaq ProLiant 5500 and 5500R Server mechanical parts

Illustrated Parts Catalog 1-3

For use with Pentium II and Pentium III Xeon processor-based servers only

System Components Exploded View (Tower Model)

11

24

20

9

1

26

10

13

23

25

8

7a

15a

22

18

21

14

19

40

Figure 1-2. Exploded view, Compaq ProLiant 5500 and 5500R Server system components

1-4 Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II and Pentium III Xeon processor-based servers only

Spare Part List

Table 1-1

Spare Part List - Compaq ProLiant 5500 and 5500R Servers

Ref. Description Spare Part Number

CHASSIS

1 Chassis 328698-001

2 Front Door Bezel 298360-001

3 Rack-Mount Bezel with Handle (Rack Model Only) 304431-001

4 Fixed Front Bezel 298361-001

5 Caster Mounting Plate with Casters (Tower Model Only) 330485-001

6 Panel Kit

a) Side Access Panel

b) U-Channel Access Panel

c) Top Access Panel

328697-001

ASSEMBLIES

7a Drive Cage with Ultra2 SCSI Backplane Board 328695-001

7b Drive Cage with Wide Ultra SCSI Backplane Board 328696-001

8 Fan Assembly 326873-001

9 Integrated Management Display (IMD) with Cable (Std. in Rack Model) 271930-001

10 Power Switch and Cable 328710-001

SYSTEM COMPONENTS

11 Hot-Plug Power Supply, 750W 169286-002

12 64-bit Dual Channel Wide Ultra2 SCSI Adapter 348759-001*

BOARDS

13 Power Backplane Board 306571-001

14 Peripheral Board 328702-001

15a Compaq 10/100 TX PCI Intel UTP Controller 317606-001

15b Compaq 10/100 TX PCI UTP Controller 169849-001*

16 400 MHz/100 (1 MB) Processor with Heat Sink 386980-001*

17 450 MHz/100 (1 MB) Processor with Heat Sink 387093-001*

18 500 MHz/100 (1 MB) Processor with Heat Sink 328700-001

continued

Illustrated Parts Catalog 1-5

For use with Pentium II and Pentium III Xeon processor-based servers only

Table 1-1

Spare Part List - Compaq ProLiant 5500 and 5500R Servers

continued

Ref. Description Spare Part Number

19 Memory Module, 64-MB, 50ns or 60ns, EDO 281858-001

20 Memory Board 328703-001

21 Processor Power Module 328701-001

22 Processor Terminator Board 329271-001

23 System I/O Board with Tray 328699-001

MEDIA STORAGE DEVICES

24 1.44-MB Diskette Drive 160788-201

25 24X or greater IDE CD-ROM Drive 328369-001

MISCELLANEOUS

26 4.5V Replacement Battery 160274-001

27 Miscellaneous Plastics Kit

a) Front Processor Guide

b) Rear Processor Guide

c) Single Board Guide *

d) Common Board Guide *

330645-001

28 Miscellaneous Slot Cover Kit 271918-001 *

29 Miscellaneous Power Cable Kit

a) Power Logic Cable Assembly

b) LCD Backplane Adapter Cable Assembly

c) 14-Inch Diskette Power Cable Assembly

d) 12-Position Power Cable Assembly

328708-001 *

30 Miscellaneous Signal Cable Kit

a) Diskette Drive Cable

b) 68-Position, 46-Inch Cable Assembly

c) Hard Drive Data and 7-Inch CD-ROM Cable Assembly

d) 12-Position Power Cable Assembly

e) Wide SCSI Signal Cable with Terminator

328709-001*

31 Removable Media Blank Bezel 306567-001

32 Hot-Plug Hard Drive Blank 1.6-Inch 189987-001

33 Hot-Plug Hard Drive Blank 1.3-Inch 296200-001 *

34 Hot-Plug Hard Drive Blank 1.0-Inch 122759-001 *

35 Rack Conversion Kit 304429-001 *

36 Return Kit 328706-001 *

37 Carton and Buns (International) 328706-002 *

38 Maintenance and Service Guide 328704-001 *

39 Illustrated Parts Map 328705-001 *

continued

1-6 Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II and Pentium III Xeon processor-based servers only

Table 1-1

Spare Part List - Compaq ProLiant 5500 and 5500R Servers

continued

Ref. Description Spare Part Number

OPTIONS

40 64-bit Dual Channel Wide Ultra2 SCSI Adapter 348759-001

41 Smart Array 3200 Controller 340855-001*

42 Keyboard (Tower Model Only) 160648-XXX *

43 Drive Cage with Duplex SCSI Backplane Board 328696-001 *

44 4.3-GB Hot-Plug Wide-Ultra SCSI-3, 10,000 rpm Hard Drive 336380-001 *

45 9.1-GB Hot-Plug Wide-Ultra SCSI-3, 10,000 rpm Hard Drive 336381-001 *

46 9.1-GB Hot-Plug Wide-Ultra SCSI-3 Hard Drive 313715-001 *

47 18.2-GB Hot-Plug Wide-Ultra SCSI-3 Hard Drive 336382-001 *

48 18.2-GB Hot-Plug Wide-Ultra SCSI-3, 10,000 rpm Hard Drive 336382-001 *

49 Memory Module, 32-MB, 50ns, EDO 281857-001 *

50 Memory Module, 128-MB, 50ns, EDO 281859-001 *

51 Memory Module, 256-MB, 50ns, EDO 281860-001 *

* Not Shown

For use with Pentium II and Pentium III Xeon processor-based servers only

Chapter 2

Removal and Replacement Procedures

This chapter provides subassembly/module-level removal and replacement procedures for

Compaq ProLiant 5500 and 5500R Servers. After completing all necessary removal and

replacement procedures, run the diagnostics program to verify that all components operate

properly.

To service Compaq ProLiant 5500 and 5500R Servers, the following items are recommended:

■ Torx T-15 screwdriver

■ Phillips screwdriver

■ From the Compaq SmartStart and Support Software CD:

!"System configuration utility software

!"Drive Array Advanced Diagnostics software

!"Diagnostics software

Electrostatic Discharge Information

A discharge of static electricity can damage static-sensitive devices or microcircuitry. Proper

packaging and grounding techniques are necessary precautions to prevent damage. To prevent

electrostatic damage, observe the following precautions:

■ Transport products in static-safe containers such as conductive tubes, bags, or boxes.

■ Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations.

■ Cover servers or work area with approved static-dissipating material. Provide a wrist strap

connected to the work surface and properly grounded tools and equipment.

■ Keep work area free of nonconductive materials such as ordinary plastic assembly aids

and foam packing.

■ Make sure you are properly grounded when touching a static-sensitive component or

assembly.

■ Avoid touching pins, leads, or circuitry.

■ Always place drives PCB (Printed Circuit Board) assembly side down.

■ Use conductive field service tools.

2-2 Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II and Pentium III Xeon processor-based servers only

Symbols in Equipment

WARNING: Any surface or area of the equipment marked with these symbols

indicates the presence of a hot surface or hot component. If this surface is

contacted, the potential for injury exists. To reduce risk of injury from a hot

component, allow the surface to cool before touching.

WARNING: Any surface or area of the equipment marked with these symbols

indicates the presence of electrical shock hazards. The enclosed area contains

no operator serviceable parts. To reduce the risk of injury from electrical shock

hazards, do not open this enclosure.

WARNING: Any RJ-45 receptacle marked with these symbols indicates a

Network Interface Connection. To reduce the risk of electrical shock, fire, or

damage to the equipment, do not plug telephone or telecommunications

connectors into this receptacle.

CLASS 1 LASER PRODUCT

WARNING: This label or its equivalent is located on the surface of your CD-ROM

drive. This label indicates that the product is classified as a CLASS 1 LASER

PRODUCT.

WARNING: Power supplies or systems marked with these symbols indicate the

equipment is supplied by multiple sources of power. To reduce the risk of injury

from electrical shock, remove all power cords to completely disconnect power

from the system.

Removal and Replacement Procedures 2-3

For use with Pentium II and Pentium III Xeon processor-based servers only

Preparation Procedures

The access panels can be removed while the server is turned on without causing system

shutdown. Auxiliary power (+5V) will remain in the exposed areas.

WARNING: Compaq ProLiant 5500 and 5500R Servers are capable of producing energy levels

that are considered hazardous.

WARNING: To completely remove all power from the system, you must disconnect the power

cord from the server. In systems with multiple power supplies, you must disconnect all the

power cords to completely remove power from the system.

IMPORTANT: It is not necessary to turn off the server to replace hot-plug devices such as hot-plug

power supplies.

Before beginning any of the removal and replacement procedures for non-hot-plug devices:

1. Power down the server.

2. Disconnect the AC power cord(s) from the AC outlet(s), then from the server.

3. Disconnect all external peripheral devices from the server.

4. If the server is in a rack-mount configuration, you must remove the server from the rack

and place it on a sturdy table or workbench to perform some removal and replacement

procedures. Refer to the Compaq ProLiant 5500 and 5500R Setup and Installation Guide

for instructions.

WARNING: To reduce the risk of personal injury or property damage, you must take

precautions to provide for rack stability and safety. Heed all cautions and warnings throughout

the installation instructions that come with the server.

WARNING: To reduce the risk of personal injury, do not attempt to remove the server from the

rack by yourself. A minimum of two people are required to remove the server from the rack.

2-4 Compaq ProLiant 5500 and 5500R Maintenance and Service Guide

For use with Pentium II and Pentium III Xeon processor-based servers only

WARNING: To reduce the risk of electric shock or damage to the equipment:

■ Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

■ Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

■ Install the power supply before connecting the power cord to the power supply.

■ Unplug the power cord before removing the power supply from the server.

■ If the system has multiple power supplies, disconnect power from the system by

unplugging all power cords from the power supplies.

CAUTION: Electrostatic discharge can damage electronic components. Be sure you are

properly grounded before beginning any installation procedure. Refer to the section titled

“Electrostatic Discharge” for more information.

Rack Warnings

WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:

■ The leveling jacks are extended to the floor

■ The full weight of the rack rests on the leveling jacks

■ The stabilizers are attached to the rack and are fully extended if it is a single rack

installation

■ Multiple racks are coupled together in multiple-rack installations

■ No more than one component is extended at a time

■ The heaviest item is loaded first and at the bottom of the rack

■ The equipment is properly supported/braced when installing options and cards

WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not

overload the AC supply branch circuit that provides power to the rack.

Removal and Replacement Procedures 2-5

For use with Pentium II and Pentium III Xeon processor-based servers only

Server Warnings and Precautions

WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system

components to cool before touching them.

43 kg

95 lb

WARNING: To reduce the risk of personal injury or damage to the equipment:

■ Observe local Occupational Safety requirements and guidelines for heavy

equipment handling.

■ Obtain adequate assistance to lift and stabilize the product during installation or

removal.

■ Remove all pluggable power supplies and modules to reduce the weight of the

product.

■ The product will be unstable when not mated with the rails.

WARNING: To reduce the risk of electric shock or damage to the equipment:

■ Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

■ Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

■ Disconnect power from the server by unplugging the power cord from either the electrical

outlet or the server.

WARNING: Protect the server from power fluctuations and temporary interruptions with a

regulating uninterruptible power supply (UPS). This device protects the hardware from damage

caused by power surges and voltage spikes and keeps the system in operation during a power

failure.

CAUTION: The ProLiant 5500 and 5500R server

must always be operated with the system unit

cover on. Proper cooling will not be achieved if the system unit cover is removed.

Page is loading ...

Compaq 5500R - ProLiant - 256 MB RAM Specification

This manual is also suitable for

Compaq 5500R - ProLiant - 256 MB RAM Specification

Related papers

Other documents