Sony Headphone User manual

OPERATING MANUAL

Bluetooth Enabled Car Kit

Version 3.5

2

OVERVIEW

This unit uses Bluetooth technology that allows wireless communication among devices such as

cellular phones. This is designed to be a totally wireless hands-free Car Kit. This will enable the

user to communicate freely while driving, without holding the phone. This unit will work on all

Bluetooth cellular phones provided that they respect the Bluetooth protocol.

1 – Multi-function Button - Answer/Hang-up/Pairing/Voice Recognition) /

Indicator lights / Timer (See page 3).

2 – Cigarette Lighter Plug - Specially designed to fit into the cigarette lighter jack

with a swivel mount up to 120°.

3 – Speaker - Allows the user to hear the voice of the other party.

4 – Volume Control - This rotary control will adjust the audio volume of the

speaker.

A. OPERATIONS

Before use, the Car Kit must be paired with the phone. This car kit requires either of two

pairing modes (Handsfree or Headset mode) which you will select depending on your cellular

phone. Pairing is done only once. After being paired, the phone and the Car Kit becomes

connected. You can answer or make a call using the car kit instead of your phone. (For the

instructions, please refer to Car Kit Operations for Popular Cell Phones on page 6).

B. INSTALLING THE MICROPHONE

1. Put two (2) "AAA" Alkaline batteries in the wireless microphone. The negative polarity of

the batteries must be in the spring side.

Note: Microphone battery life is more than 500 calls (if 3 calls/day, battery life = more

than 5 months).

2. It is highly recommended that you attach your microphone to the sun visor(See figure

3). Please make sure that it does not hide the microphone otherwise your voice will be

attenuated.

3. Turn "ON" the microphone by using the power switch.

Figure 1

3

Note:

On high background environment,

If you experience audio level

fluctuation, turn ASP ‘’ OFF ’’.

Recommended Function Controls

Setting (Working on all models):

MIC = L

ASP = ON

TONE = H

• Wireless Microphone Illustration

REMARKS:

§ If microphone is not “ON” during a communication, the sound on the speaker will be

attenuated.

§ In standby mode, the microphone will still have a small consumption (less than 1.8

microwatts).

§ On some versions, the indicator light will only turn ON for 2 seconds after the

microphone is switched ON. If the light is red, this indicates low battery.

§ The microphone is activated by the Hands-Free Car Kit base and can remain in “ON”

position even if not used. But in order to extend battery life, it is recommended to switch

“OFF” your microphone when you won’t use it for a long time.

C. FUNCTION CONTROLS

Adjust the Function Controls as recommended:

1. Tone Control

“H” for High Tone

“L” for Low Tone.

2. ASP Control

ON = Echo and Feedback Canceller

OFF = Echo Reducer only

3. Adjustable Microphone Gain (MIC) Control

“H” for high gain; “L” for low gain.

"L" is necessary in noisy background. Control Switches

The Microphone gain must be adjusted to match with your cell phone model. If the gain is too

high, it can cause feedback (whistling sound), echo or background noise during calls on some

cell phones.

D. SETTING THE VOLUME

There are two volume controls. One is on the main unit. See (4) on figure 1. The other is the

volume key of your cell phone. Use the volume control of the Car Kit and the volume keys of

your cell phone. Note: If the volume set is too high, it can cause feedback (whistling sound),

echo or background noise during calls on some cell phones.

Figure 3

Figure 2

Figure 4.

4

E. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, the phone ring tone will be heard on the Car Kit. Just

press the multi-function button (1) on the main unit to answer the call. Pressing the button

again will hang-up and terminate the call. (Please refer to Car Kit Operations for Popular Cell

Phones section on page 4 for additional information).

F. MAKING A CALL

(Refer to Car Kit Operations For Popular Cell Phones section on page 4).

Important Remarks:

• On some versions of Nokia’s software, the Car Kit will not connect automatically to the

cell phone. You will need to press the multi-function button once to connect it to the cell

phone.

• If disconnection problem will be encountered on some Nokia cell phones, kindly turn off

the keypad tone of your cell phone.

5

CAR KIT OPERATIONS FOR POPULAR

CELL PHONES

Note 1: If your phone is not included in the following list of this manual, kindly refer to the manual

of your phone.

Note 2: Softwares and menus could be modified by the cell phone’s manufacturers without prior

notice. If the manual does not match with your cell phone operations, kindly refer to the manual of

your cell phone.

Note 3: Multi-pairing is now possible.

Ericsson T39m ………………………………….……………………… 8

Sony Ericsson T68/T68i ……………………………….………………………… 9

Sony Ericsson P800 / P900 ………………………………….……………………… 12

Sony Ericsson T610 ………………………………….……………………… 14

Sony Ericsson T628 ………………………………….……………………… 15

Sony Ericsson Z600 ………………………………….……………………… 17

Sony Ericsson K700i ………………………………….……………………… 18

Motorola E398 ………………………………….……………………… 20

Motorola V80 ………………………………….……………………… 22

Motorola V600 ………………………………….……………………… 23

Nokia 6310/6310i ………………………………….……………………… 25

Nokia 8910 ………………………………….……………………… 27

Nokia 8910i ………………………………….……………………… 29

Nokia 3650 ………………………………….……………………… 31

Nokia 6230 ………………………………….……………………… 33

Nokia 6650 ………………………………….……………………… 34

Nokia 6600 ………………………………….……………………… 36

Panasonic X70 ………………………………….……………………… 38

Qtek 2020 ………………………………….……………………… 40

Sharp GX32 ………………………………….……………………… 41

Siemens S55 ………………………………….……………………… 42

6

Suggested Pairing Modes

Pairing Mode

Cell Phone Models

Handsfree Headset

Ericsson T39m

Sony Ericsson T68

Sony Ericsson T68i (R6 and below)

Sony Ericsson T68i (R7)

Sony Ericsson P800 / P900

Sony Ericsson T610

Sony Ericsson T628

Sony Ericsson Z600

Sony Ericsson K700i

Motorola E398

Motorola V80

Motorola V600

Nokia 6310/6310i

Nokia 8910

Nokia 8910i

Nokia 3650

Nokia 6230

Nokia 6650

Nokia 6600

Panasonic X70

Qtek2020

Sharp GX32

Siemens S55

The Car Kit turns on automatically when the engine is turned on. The

ON state is designated by the Bluetooth indicator LED flashing “Blue”.

Note 1: Handsfree Pairing Mode

From the ON state, press the multi-function button for 10 seconds or

until a distinctive three-tone sound will be heard and at the same time,

the Bluetooth indicator LED changes from blinking blue to alternate

blinking of red and blue. This indicates that the unit is now ready for

Handsfree Pairing.

Note 2: Headset Pairing Mode

From the ON state, press the multi-function button for 10 seconds or

until a distinctive three-tone sound will be heard and at the same time,

the Bluetooth indicator LED changes from blinking blue to alternate

blinking of red and blue.

Press the multi-function button again for a short time to access

Headset Pairing Mode.

7

USING WITH SONY ERICSSON T39m

a. ACTIVATING THE BLUETOOTH

You must activate your Bluetooth to establish a Bluetooth connection between

your mobile phone and other Bluetooth devices.

1. Press Menu Key. Scroll to Extras and press YES. Select Operation mode, YES. On,

YES.

2. Continue pressing NO to exit.

QUICK ACCESS:

Press Menu followed by the sequence of numbers below.

Extras Blue tooth Operation mode

T39m 5 6 4

b. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Press the multi-function button once again for a short time, to access headset

pairing mode.

4. Press Menu Key. Scroll to Extras, YES. Select Bluetooth, YES. Select Paired devices,

YES. Add device, YES. Choose Phone initiates, YES. Choose Headset, YES. The

phone will then search the device to be added. After the device is found, press YES.

QUICK ACCESS (for step 4):

Press Menu then follow the sequence of numbers below:

Extras Blue tooth

Paired

devices

Add

device

Phone

initiates

Headset

T39m 5 6 2 Yes 1 2

5. Enter “0000” as the passkey. If the pairing is successful, the alternating red/blue lights

will stop. Press YES to confirm the name of the device. If pairing is unsuccessful, the

steps above may be repeated.

6. Continue pressing NO to exit from Menu.

The unit is now ready to link calls from the phone directly to the Car Kit.

c. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, a ring tone will be heard on the Car Kit.

1. Press the multi-function button once to answer the call. Note: Pressing the button again

will hang-up and terminate the call.

2. If you wish to answer the call on the cellular phone, just press YES and audio will be

heard on the phone. If you press once on the multi-function button, audio will be

transferred to the Car Kit.

3. Pressing the multi-function button once again will terminate the call.

d. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press YES. Audio can be heard on the Car Kit.

Simultaneously, a question “Retrieve call in phone?” will be displayed. Ignoring

or pressing No, will retain the call to the Car Kit. Pressing Yes will transfer the

audio to the cell phone.

2. Press the multi-function button to hang-up and terminate the call.

8

Voice dialing

Refer to step f and g for the procedure when activating and recording for voice dialing.

1. Press the multi-function button once to activate the voice dialing.

2. A beep will then be heard on the Car Kit prompting the user to say the name of

the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Press the multi-function button once again to terminate the call.

e. AUDIO TRANSFER

Audio Transfer can be done by pressing the multi-function button or accessing the cell

phone’s menu during ongoing calls.

f. ACTIVATING THE VOICE DIALING

Use your phone when recording for voice dialing. Before voice dialing, you must first turn on

the name dialing function and record your voice. To turn voice dialing on and record number

types:

1. Press Menu Key. Scroll to Settings, YES. Voice control, YES.

2. Voice settings, YES. Voice dialing, YES. Select On, YES.

3. Continue pressing NO to exit.

QUICK ACCESS:

Press Menu followed by the sequence of numbers below.

Settings Voice control Voice settings Voice dialing On

T39m 4 9 1 1 1

g. RECORDING FOR VOICE DIALING

1. Press Menu Key. Scroll to Settings, YES. Voice control, YES. Voice Commands, YES.

Select Contacts, YES. Add voice, YES.

2. Find a contact name and follow the instructions in the display. An icon will appear next

to a contact name which has a voice command.

3. Continue pressing NO to exit.

QUICK ACCESS:

Press Menu followed by the sequence of numbers below.

Settings Voice control Voice commands Contacts

T39m 4 9 2 4

Note: Noisy environment may affect voice recognition. Record your voice in a quiet

environment.

USING WITH SONY ERICSSON T68/T68i

a. ACTIVATING THE BLUETOOTH

You must activate your Bluetooth to establish a Bluetooth connection between your mobile

phone and other Bluetooth devices.

1. Go to Menu by pressing the joystick. Scroll to Connect, YES. Select Bluetooth, YES.

Select Options, YES. Operation mode, YES. On, YES.

2. Continue pressing NO to exit.

9

QUICK ACCESS:

Press Menu followed by the sequence of numbers below.

Connect Blue tooth Options Operation mode

T68 8 3 - 2

T68i 8 4 (or 3 for T68i R7) 4 1

b. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. For T68 and T68i older versions, R6 and below, press the multi-function button

once again for a short time, to access headset pairing mode.

4. Go to Menu by pressing the joystick. Scroll to Connect, YES. Select Bluetooth, YES.

5. Select Paired devices, YES. Add device, YES. Choose Phone initiates, YES. Choose

Headset/Handsfree, YES. The phone will then search the device to be added. After the

device is found, press YES.

QUICK ACCESS (for steps 4 and 5):

Press Menu then follow the sequence of numbers below:

Connect Blue tooth

Paired

devices

Add

device

Phone

initiates

Headset/

Handsfree

T68 8 3 2 Yes 1 2

T68i 8 4 (or 3 for T68i R7) 2 Yes 1 2

6. Enter “0000” as the passkey. If pairing is successful, the alternating red/blue lights will

stop. Press YES to confirm the name of the device. If pairing is unsuccessful, the steps

above may be repeated.

7. Continue pressing NO to exit from menu.

The unit is now ready to link calls from the phone directly to the Car Kit. An icon, will appear

during the standby mode indicating that the Car Kit is linked with the phone.

c. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, a ring tone will be heard on the Car Kit.

1. Just press the multi-function button once to answer the call. Pressing the button again

will hang-up and terminate the call.

2. If you wish to answer the call on the cellular phone, just press YES and the call will be

heard on the phone. Pressing the multi-function button will transfer the call to the Car

Kit.

3. To terminate the call, press the multi-function button again.

d. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press YES. Audio will be heard on the Car Kit.

Simultaneously, a question “Retrieve call in phone?” will be displayed. Ignoring

or pressing No, will retain the audio to the Car Kit. Pressing Yes, will transfer the

audio to the cell phone.

2. Press the multi-function button to terminate the call.

Voice dialing

Refer to step g and h for the procedure when activating and recording for voice dialing.

1. Press the multi-function button once to activate the voice dialing.

10

2. A beep will then be heard on the Car Kit prompting the user to say the name of

the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Press the button again to terminate the call.

Redialing

For T68i R6 and R7, press twice quickly the multi-function button. Call is automatically

transferred to the Car Kit.

e. AUDIO TRANSFER

Audio Transfer can be done by pressing the multi-function button or accessing the cell

phone’s menu during ongoing calls.

f. REJECTING A CALL

For T68i R6 and R7, press the multi-function button twice to reject the incoming call.

g. ACTIVATING THE VOICE DIALING

Use your phone when recording for voice dialing. Before voice dialing, you must first turn on

the name dialing function and record your voice. To turn voice dialing on and record number

types:

Using T68 Sony Ericsson

1. Go to Menu by pressing the joystick. Scroll to Settings, YES. Voice control, YES.

2. Voice settings, YES. Voice dialing, YES. Select On, YES.

3. Continue pressing NO to exit

Using T68i Sony Ericsson

1. Go to Menu by pressing the joystick. Scroll to Settings, YES. Voice control, YES.

Voice dialing, YES.

2. Select On, YES.

3. Continue pressing NO to exit

QUICK ACCESS:

Press Menu followed by the sequence of numbers below.

Settings

Voice

control

Voice

settings

Voice

dialing

On

T68 5 8 1 1 1

T68i 5 6 - 1 1

h. RECORDING FOR VOICE DIALING

Using T68 Sony Ericsson

1. Go to Menu by pressing the joystick. Scroll to Settings and press YES. Choose

Voice control, YES. Voice Commands, YES. Select a contact, YES. Add voice,

YES.

2. Follow the instructions in the display. An icon will appear next to a contact name

which has a voice command.

3. Continue pressing NO to exit.

Using T68i Sony Ericsson

1. Go to Menu by pressing the joystick. Scroll to Settings and press YES. Choose

Voice control, YES then go to Voice dialing, YES. Edit name, YES. Add voice,

YES.

2. Select a contact, YES.

11

3. Follow the instructions in the display. An icon will appear next to a contact name

which has a voice command.

4. Continue pressing NO to exit.

QUICK ACCESS:

Press Menu followed by the sequence of numbers below.

Settings Voice control Voice commands Contacts

T68 5 8 2 4

Settings Voice control Voice dialing Edit names

T68i 5 6 1 2

Note: Record your voice command in a quiet place so that only your voice will be

recorded on the phone.

USING WITH SONY ERICSSON P800 / P900

a. ACTIVATING THE BLUETOOTH

You must activate your Bluetooth to establish a Bluetooth connection between your mobile

phone and other Bluetooth devices.

1. Flip to open mode. On the phone’s Applications window, scroll to Control Panel and

tap it using the “stylus”. On the lower portion, tap Connections index. Tap

Bluetooth.Tap Settings index. On the Operation mode, tap On.

2. Tap to exit and return to the Applications window.

b. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Press the multi-function button once again for a short time, to access headset

pairing mode.

4. Flip to open mode. On the phone’s Applications window, scroll to Control Panel and tap

it. On the lower portion, tap Connections index. Tap Bluetooth. Tap Devices index.

Bluetooth devices is displayed as sub-title. Tap Add. The phone is now searching for

pairable devices.

5. Devices found are then displayed. Tap the device you want to pair with your phone.

Bonding in progress will be displayed on screen and simultaneously, the phone will

ask for the pass key.

6. On the lower left corner of the screen, tap . Enter “0000” as the passkey then tap

Done. Also tap Done under the sub-title, “Secure Connection.” If pairing is successful,

the alternating red/blue lights will stop.

7. Tap to exit and return to the Applications window. If the pairing is unsuccessful, the

steps above may be repeated.

The unit is now ready to link calls from the phone directly to the Car Kit. An icon will

appear during the standby mode indicating that the Car Kit is linked with the phone.

c. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, a ring tone will be heard on the Car Kit.

1. Press the multi-function button once to answer the call. Pressing the button again will

hang-up and terminate the call.

12

2. If you wish to answer the call on the cellular phone, just press ok key and audio will be

heard on the phone. Pressing the multi-function button will transfer the audio to the Car

Kit.

3. To terminate the call, press the multi-function button again.

d. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press OK. Sound is automatically transferred to the

Car Kit.

2. Press the multi-function button to hang-up and terminate the call.

Voice dialing

Refer to step f and g for the procedure when activating and recording for voice dialing.

1. Press the multi-function button once to activate the voice dialing. Sound is

automatically transferred to the Car Kit.

2. A beep will then be heard on the Car Kit prompting the user to say the name of

the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Press the button again to terminate the call.

e. AUDIO TRANSFER

Audio Transfer can be done by pressing the multi-function button or accessing the cell

phone’s menu during ongoing calls.

f. ACTIVATING THE VOICE DIALING

Use your phone when recording for the voice dialing. Before voice dialing, you must first turn

on the name dialing function and record your voice. To turn voice dialing on:

1. On the Applications window (flip open mode), tap Phone.

2. Tap Edit then tap Preferences. A list of features will appear.

3. Tap Voice Control then tap the box aligned to Voice dialing to check and activate the

voice dialing feature. Tap the box aligned to Play caller name so that the name will be

played back to you.

4. Tap Done on the on screen button when finished.

5. On the Preferences mode, tap Done again.

6. Tap to exit and return to the Applications mode.

g. RECORDING FOR VOICE DIALING

The voice dialing feature is only applicable to contacts saved to phone memory.

1. On the Applications window (flip open mode), tap Contacts.

2. Tap the contact where you want to add a voice dialing feature. Tap Edit. Scroll to Edit

Contact. Tap on the on-screen buttons.

3. Tap Record. Speak after tone will be displayed on the screen.

4. Record your voice. To check if your recording is of good quality, tap Play. If not, tap

Record again. Press Done when finished.

5. Tap to make another record and repeat the steps above. To return to the

Applications window, tap button.

Note: Noisy environment may affect voice recognition. Record your voice in a quiet

environment.

13

USING WITH SONY ERICSSON T610

a. ACTIVATING THE BLUETOOTH

You must activate your Bluetooth to establish a Bluetooth connection between your mobile

phone and other Bluetooth devices.

1. Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,

SELECT. Turn On, SELECT.

2. Continue pressing to exit.

b. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,

SELECT.

4. Scroll to My devices, SELECT. New device, ADD. The phone is now searching for

pairable devices to be added. Select the device you want to pair with your cell phone.

Press SELECT.

5. Enter “0000” as the passkey then press OK. If the pairing is successful, the alternating

red/blue lights will stop.

6. Continue pressing to exit.

The unit is now ready to link calls from the phone directly to the Car Kit. An icon will appear

during the standby mode indicating that the Car Kit is linked with the phone.

c. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, a ring tone will be heard on the Car Kit.

1. Just press the multi-function button down once to answer the call. Pressing the button

again will hang-up and terminate the call.

2. If you wish to answer a call on the cellular phone, just press YES and the call is

automatically transferred to the phone. Pressing the multi-function button transfers the

call on the Car Kit.

3. To terminate the call, press the multi-function button again.

d. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press CALL button. Audio is automatically

transferred to the Car Kit.

2. Press the multi-function button to hang-up and terminate the call.

Voice dialing

Refer to step g and h for the procedure when activating and recording for voice dialing.

1. Press the multi-function button once to activate the voice dialing.

2. A beep will then be heard on the Car Kit prompting the user to say the name of

the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Press the multi-function button again to terminate the call.

Redialing

Press quickly the multi-function button twice to redial the last number.

14

e. AUDIO TRANSFER

Audio Transfer can be done by pressing the multi-function button or accessing the cell

phone’s menu during ongoing calls.

f. REJECTING A CALL

Press the multi-function button twice to reject the incoming call.

g. ACTIVATING THE VOICE DIALING

Use your phone when recording for the voice dialing. Before voice dialing, you must first turn

on the name dialing function and record your voice. To turn voice dialing on and record

number types:

1. Go to Menu by pressing the joystick. Scroll to Settings, SELECT. Voice control,

SELECT. Voice dialing, SELECT.

2. Choose On, SELECT.

3. Continue pressing to exit.

h. RECORDING FOR VOICE DIALING

1. Go to Menu by pressing the joystick. Scroll to Settings and press SELECT. Choose

Voice control, SELECT then go to Voice dialing, SELECT. Edit names, SELECT. New

voice, ADD.

2. Find a contact then press SELECT.

3. Follow the instructions that are displayed. Voice is automatically saved on the phone.

An icon will appear next to a contact name which has a voice command.

4. Continue pressing to exit.

Note: Noisy environment may affect voice recognition. Record your voice in a quiet

environment.

USING WITH SONY ERICSSON T628

a. ACTIVATING THE BLUE TOOTH

You must activate your Bluetooth to establish a Bluetooth connection between your mobile

phone and other Bluetooth devices.

1. Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,

SELECT. Turn On, SELECT.

2. Continue pressing to exit.

b. SETTING TO LOW POWER MODE

1. Press Menu Key. Scroll to Connectivity, SELECT. Bluetooth, SELECT.

2. Scroll to Handsfree, SELECT. Choose Car handsfree, SELECT.

3. Choose Power Save, SELECT.

4. Continue pressing to exit.

c. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,

SELECT.

4. Scroll to My devices, SELECT. New device, ADD. The phone is now searching for

pairable devices to be added. Select the device you want to pair with your cell phone.

Press SELECT.

15

5. Enter “0000” as the passkey then press OK. If the pairing is successful, the alternating

red/blue lights will stop.

6. Continue pressing to exit from Menu.

The unit is now ready to link calls from the phone directly to the Car Kit. An icon, will appear

during the standby mode indicating that the Car Kit is linked with the phone.

d. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, a ring tone will be heard on the Car Kit.

1. Just press the multi-function button down once to answer the call. Pressing the button

again will hang-up and terminate the call.

2. If you wish to answer a call on the cellular phone, just press YES and audio will be

heard on the phone. Pressing the multi-function button will transfer the call on the Car

Kit.

3. To terminate the call, press the multi-function button again.

e. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press CALL button. Audio is automatically

transferred to the Car Kit.

2. Press the multi-function button to hang-up and terminate the call.

Voice dialing

Refer to step g and h for the procedure when activating and recording for voice dialing.

1. Press the multi-function button once to activate the voice dialing.

2. A beep will then be heard on the Car Kit prompting the user to say the name of

the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Press the multi-function button again to terminate the call.

f. AUDIO TRANSFER

Audio Transfer can be done by pressing the multi-function button or accessing the cell

phone’s menu during ongoing calls.

g. ACTIVATING THE VOICE DIALING

Use your phone when recording for voice dialing. Before voice dialing, you must first turn on

the name dialing function and record your voice. To turn voice dialing on and record number

types:

1. Go to Menu by pressing the joystick. Scroll to Settings, SELECT. Voice control,

SELECT. Voice dialing, SELECT.

2. Choose On, SELECT.

3. Continue pressing to exit.

h. RECORDING FOR VOICE DIALING

1. Go to Menu by pressing the joystick. Scroll to Settings and press SELECT. Choose

Voice control, SELECT then go to Voice dialing, SELECT. Edit names, SELECT. New

voice, ADD.

2. Find a contact then press SELECT.

3. Follow the instructions that are displayed. Voice is automatically saved on the phone.

An icon will appear next to a contact name which has a voice command.

4. Continue pressing to exit.

Note: Noisy environment may affect voice recognition. Record your voice in a quiet

environment.

16

USING WITH SONY ERICSSON Z600

a. ACTIVATING THE BLUETOOTH

You must activate your Bluetooth to establish a Bluetooth connection between your mobile

phone and other Bluetooth devices.

1. Press Menu Key . Scroll to Connectivity, SELECT. Bluetooth, SELECT. Choose

Turn ON, SELECT.

2. Continue pressing to exit.

QUICK ACCESS:

a. Press More key.

b. Scroll to Turn On Blue tooth, SELECT.

c. Continue pressing to exit.

b. SETTING TO LOW POWER MODE

1. Press Menu Key . Scroll to Connectivity, SELECT. Bluetooth, SELECT.

2. Scroll to Handsfree, SELECT. Choose Car handsfree, SELECT.

3. Choose Power Save, SELECT.

4. Continue pressing to exit.

c. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Press Menu Key . Scroll to Connectivity, SELECT. Bluetooth, SELECT.

4. Scroll to My Devices, SELECT. New Device, ADD. The phone will then search the

device to be added. After the device is found, press SELECT.

5. Enter “0000” as the passkey and press OK. If the pairing is successful, the alternating

red/blue lights will stop. If pairing is unsuccessful, the steps above may be repeated.

6. Continue pressing to exit.

The unit is now ready to link calls from the phone directly to the Car Kit. An icon, will appear

during the standby mode indicating that the Car Kit is linked with the phone.

d. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, a ring tone will be heard on the Car Kit.

1. Just press the multi-function button down once to answer the call. Pressing the button

again will hang-up and terminate the call.

2. If you wish to answer a call on the cellular phone, just press YES and the call is

automatically transferred to the phone. To transfer the call to the Car Kit, Press Menu

Key. Scroll to Transfer Sound and press SELECT. Choose the paired device and press

SELECT.

3. To terminate the call, press the multi-function button again.

e. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and send. Audio can be heard on the Car Kit

simultaneously.

2. Press the multi-function button to hang-up and terminate the call.

Voice dialing

Refer to step g and h for the procedure when activating and recording for voice dialing.

1. Press the multi-function button once to activate the voice dialing.

17

2. A beep will then be heard on the Car Kit prompting the user to say the name of

the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Press the button again to terminate the call.

f. AUDIO TRANSFER

Audio Transfer can be done by pressing the multi-function button or accessing the cell

phone’s menu during ongoing calls.

g. ACTIVATING THE VOICE DIALING

Use your phone when recording for the voice dialing. Before voice dialing, you must first turn

on the voice dialing function and record your voice. To turn voice dialing on:

1. Press Menu Key . Scroll to Settings, SELECT. Scroll to Voice control, SELECT.

Voice dialing, SELECT.

2. Choose On, SELECT.

3. Continue pressing to exit.

h. RECORDING FOR VOICE DIALING

1. Press Menu Key . Scroll to Settings and press SELECT. Choose Voice controls,

SELECT then go to Voice dialing, SELECT. Scroll to Edit name, SELECT. New voice,

ADD.

2. Select a contact and press SELECT.

3. Follow the instructions in the display. An icon will appear opposite a contact’s name

which has a voice command.

4. Continue pressing to exit.

Note: Record your voice command in a quiet place so that only your voice will be recorded on

the phone.

USING WITH SONY ERICSSON K700i

a. ACTIVATING THE BLUETOOTH

You must activate the Bluetooth feature of your phone to establish a Bluetooth connection

between your mobile phone and other Bluetooth devices.

1. Press to access Main Menu.

2. Scroll to Connectivity, Select. Bluetooth, Select. Turn On, Select.

3. Continue pressing to exit.

b. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Press to access Main Menu. Scroll to Connectivity, Select. Choose Bluetooth,

Select.

4. Scroll to My devices, Select. New device, Add. The phone will then search for pairable

devices to be added.

5. The searched devices will then be displayed. Choose the device name you want to pair

with this phone, then press Select.

18

6. Enter “0000” as the passcode then press Ok. If pairing is successful, the alternating

red/blue lights (Bluetooth Indicator) will stop and will change to plain blinking blue.

7. Your device name is now added under My devices tab. Highlight the newly paired

device and then press Connect to completely establish connection between your mobile

phone and your Car Kit.

8.

When a statement appeared indicating that your device is connected, continue pressing

to exit.

The Car kit is now linked or paired with the phone. If pairing is unsuccessful, the steps

above may be repeated.

c. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, ring tone will be heard on the phone and on the Car Kit.

1. Shortly press the multi-function button once to answer the call.

2. Shortly press the multi-function button once to terminate the call.

d. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press Call key. Audio is possible on the phone or on

the kit.

At times, when the audio is not on the kit, apply audio transfer (see section e).

2. To terminate or hang-up the call, shortly press the multi-function button.

Voice dialing

Refer to step h and i for the procedure when activating and recording for voice dialing.

1. Shortly press the multi-function button once to activate voice dialing.

2. A beep will then be heard on the Car Kit prompting the user to say the voice name

of the person to call.

3. Say the name. The voice name will be played back to you. The phone will then

place the call automatically. In case the cell phone does not recognize the name

spoken, the steps above may be repeated.

4. Shortly press the hang-up button to terminate the call.

Redialing

Press the multi-function button twice quickly to redial the last number.

e. AUDIO TRANSFER

Audio transfer can be done during an ongoing call.

Car kit initiates transfer from kit to phone: Press twice quickly the multi-function button.

Car kit initiates transfer from phone to kit: Shortly press the multi-function button once.

Note: Using your phone, access (Menu button) during an ongoing call to transfer sound

to the Car Kit or to your phone.

f. REJECTING A CALL

Press the multi-function button twice quickly to reject an incoming call.

g. ACTIVATING THE VOICE DIALING

Before voice dialing, you must first activate the voice dialing function of your cell phone and

record a voice command for a particular contact.

1. Press to access Main Menu. Scroll to Settings, Select. Voice control, Select.

Voice dialing, Select. Activate, Select.

2. Continue pressing to exit.

19

h. RECORDING FOR VOICE DIALING

Note: Voice dialing entries must be stored in the phone’s memory (not on the SIM

card!).

1. Press to access Main Menu. Scroll to Settings and press Select. Choose Voice

control, Select. Voice dialing, Select. Edit names, Select. New voice, Add.

(Contacts list will appear).

2. Choose among the contacts whichever you want to have a voice name/voice tag. When

it’s highlighted, press Select.

3. Follow the instructions that will be displayed on screen.

Note: You may use any word(s) or just say the person’s name for a voice tag.

4. When your spoken word(s) is caught up by the phone, it will ask you to listen to your

recording and will ask the question, “Is it ok?”.

5. As soon as you press Yes as reply, your voice command will be saved. Under Voice

Commands tab, a callout icon will appear next to a contact name which has a voice

command.

6. Continue pressing to exit.

Note: Noisy environment may affect voice recognition. Record a voice and make a voice dial

in a quiet environment.

USING WITH MOTOROLA E398

a. ACTIVATING THE BLUETOOTH

You must activate the Bluetooth feature of your mobile phone to establish a Bluetooth

connection between your mobile phone and other Bluetooth devices.

1. Press or to access Main Menu.

2. Scroll to Settings, SELECT. Scroll to Connection, SELECT. Bluetooth Link,

SELECT.

Set-up, SELECT. Scroll to Power: Off. Press CHANGE. Choose On, SELECT.

3. Continue pressing BACK to exit.

b. PAIRING TO THE CELLULAR PHONE

1. Bring the cellular phone at about 20 cm from the Car Kit.

2. From the ON state, press the multi-function button for 10 seconds or until a distinctive

three-tone sound will be heard and at the same time, the Bluetooth indicator LED

changes from blinking blue to alternate blinking of red and blue. This indicates that the

unit is now ready for pairing.

3. Press or to access Menu. Scroll to Settings, SELECT. Choose Connection,

SELECT. Bluetooth Link, SELECT.

4. Choose Handsfree, SELECT. [Look for devices], SELECT. The phone will then scan

devices until it displays them in the list.

5. Under scan results, choose the device you want to pair with your mobile phone and

press SELECT. A question “Bond With (device name)?” appears. Press YES.

6. Enter Bluetooth Passkey “0000” then press ok. If pairing is successful, a remark

“Connected…” appears. The phone exits automatically.

The Car kit is now linked or paired with the phone. If pairing is unsuccessful, the steps

above may be repeated.

c. ANSWERING/RECEIVING A CALL

When the phone is receiving a call, ring tone will be heard on the phone and on the Car Kit.

1. Shortly press the multi-function button once to answer the call.

2. To terminate the call, do the same; shortly press the multi-function button once.

20

e. MAKING A CALL with the Car Kit on

Normal dialing

1. Enter the contact number and press Call key. Audio will be heard on

the Car Kit.

2. To terminate or hang-up the call, shortly press the multi-function button.

Voice dialing

Make a phone call by saying a voice name / voice tag. But first refer to step h and i for

the procedure when recording for voice dialing.

1. Press the multi-function button once to activate voice dialing.

2. A beep will then be heard on the Headset prompting the user to say the voice

name / voice tag of the person to call.

3. Say the name. The name will be played back to you. The phone will then place

the call automatically. In case the cellular phone does not recognize the name

spoken, the steps above may be repeated.

4. To terminate or hang-up the call, shortly press the multi-function button.

Redialing

Press the multi-function button twice quickly to redial the last number.

e. AUDIO TRANSFER

Audio transfer can be done during an ongoing call.

Car kit initiates transfer from kit to phone: Press twice quickly the multi-function button.

Car kit initiates transfer from phone to kit: Shortly press the multi-function button once.

Note: Using your phone for audio transfer, press button to access Call Menu and

transfer audio by Selecting “Use Handset” or “Use Bluetooth”.

f. REJECTING A CALL

Press the multi-function button twice quickly to reject an incoming call.

g. ACTIVATING THE VOICE DIALING

Use your phone when recording for voice dialing. Before voice dialing, you must first turn on

the Voice Dial function and record your voice. To turn voice dialing on:

1. Press or to access Menu. Scroll to Settings, SELECT. Scroll to Headset,

SELECT.

2. Choose Voice Dial, CHANGE. Choose ON, SELECT.

3. Continue pressing Back to exit.

i. RECORDING FOR VOICE DIALING

Note: Voice dialing entries must be stored in the phone’s memory (not on the SIM

card!).

1. Press or to access Menu. Scroll to Phonebook, SELECT.

2. Choose a contact which you want to have a voice name/tag, press VIEW then EDIT.

3. On the Entry Details, choose “Store To: ____” and press CHANGE. Choose Phone,

SELECT. (This is storing the number to phone memory).

4. Highlight “Voice Name: ___” then press RECORD.

Follow instructions on the screen. Note: You may use any word(s) or just the person’s

name for a voice name/ tag.

Note: If recording is successful, a statement “Trained: Voice Name” appears. An icon

will appear next to Voice Name.

5. Press DONE.

6. Continue pressing key to exit.

Note: In the listed names of your Phonebook, a symbol appears next to a name

which has a “Voice Name”. This indicates that you can contact this person via “voice

dial”.

Page is loading ...

Sony Headphone User manual

Sony Headphone User manual

Related papers

Other documents