DataVideo HS-1600T Mark II User manual

Brand: DataVideo

Model: HS-1600T Mark II

Category: Supplementary music equipment

Type: User manual

4 CHANNEL HD/SD

HS-1600T MKII

HDBASET PORTABLE

VIDEO STREAMING STUDIO

Instruction Manual

Table of Contents

FCC COMPLIANCE STATEMENT .........................................................................................................5

WARNINGS AND PRECAUTIONS .......................................................................................................5

WARRANTY .....................................................................................................................................6

STANDARD WARRANTY ................................................................................................................................. 6

THREE YEAR WARRANTY ............................................................................................................................... 6

DISPOSAL.........................................................................................................................................7

CHAPTER 1 INTRODUCTION ...........................................................................................................8

1.1 FEATURES ....................................................................................................................................... 8

1.2 SYSTEM DIAGRAM ............................................................................................................................ 9

CHAPTER 2 CONNECTIONS AND CONTROLS ................................................................................. 10

2.1 REAR PANEL .................................................................................................................................. 10

2.2 SWITCHER KEYBOARD PANEL ............................................................................................................ 13

2.3 MONITOR CONTROL PANEL .............................................................................................................. 21

2.4 RECORD/STREAM PANEL ................................................................................................................. 22

CHAPTER 3 SWITCHER OSD MENU ............................................................................................... 24

3.1 START .......................................................................................................................................... 24

Transition Type ................................................................................................................................. 24

Transition Speed ............................................................................................................................... 24

Wipe Effect ........................................................................................................................................ 25

WIPE Border Size ............................................................................................................................... 25

WIPE Border Color ............................................................................................................................ 25

BKG Color .......................................................................................................................................... 25

3.2 PIP / SPLIT .................................................................................................................................... 25

PIP Source ......................................................................................................................................... 26

PIP Size (PIP Window Size) ................................................................................................................ 26

Position X .......................................................................................................................................... 26

Position Y .......................................................................................................................................... 27

Split Source ....................................................................................................................................... 27

Border Size ........................................................................................................................................ 27

Border Color ...................................................................................................................................... 27

3.3 PIP CROP ..................................................................................................................................... 27

3.4 LUMAKEY ...................................................................................................................................... 28

Lumakey Source ................................................................................................................................ 28

Mode ................................................................................................................................................. 28

Cleanup Level .................................................................................................................................... 28

Transparency .................................................................................................................................... 28

3.5 AUDIO .......................................................................................................................................... 29

Mute ................................................................................................................................................. 29

HDMI Input ....................................................................................................................................... 29

HDMI Group ...................................................................................................................................... 29

Level .................................................................................................................................................. 29

Tally Mode ........................................................................................................................................ 29

3.6 USER MEMS .................................................................................................................................. 30

Load Memory .................................................................................................................................... 30

Save Memory .................................................................................................................................... 30

Factory Default ................................................................................................................................. 30

3.7 SETUP .......................................................................................................................................... 30

PGM Out Res. .................................................................................................................................... 31

MV Out Res. ...................................................................................................................................... 31

Output Format .................................................................................................................................. 32

Save Setup ......................................................................................................................................... 32

Language .......................................................................................................................................... 32

MB and KBD Software ...................................................................................................................... 32

3.8 CAMERA ....................................................................................................................................... 32

Camera CH. Setup ............................................................................................................................. 33

PTC-150T-01/02/03 .......................................................................................................................... 33

Camera Info ................................................................................................................................... 33

Video ............................................................................................................................................. 33

Operator ........................................................................................................................................ 33

CHAPTER 4 MONITOR .................................................................................................................. 34

4.1 MENU OPTIONS ........................................................................................................................... 34

MAIN ADJUST .................................................................................................................................... 35

COLOR ............................................................................................................................................... 35

Information ....................................................................................................................................... 35

Special Function ................................................................................................................................ 36

Factory Reset .................................................................................................................................... 36

CHAPTER 5 APPLICATIONS ........................................................................................................... 37

5.1 PLACING A LOGO ON THE VIDEO USING THE LUMAKEY FUNCTION .............................................................. 37

5.2 CONNECTING PTC-150T CAMERAS ................................................................................................... 37

CHAPTER 6 VIDEO STREAMING AND RECORDING ......................................................................... 39

6.1 STREAMING NETWORK CONNECTION AND DEVICE SEARCH ..................................................................... 39

Connecting to a DHCP Network (DHCP Mode) ................................................................................. 39

Connecting to a NON-DHCP Network (Static IP) .............................................................................. 40

Default Fixed IP ............................................................................................................................. 40

Troubleshooting the Network Connection ........................................................................................ 40

Advanced Troubleshooting ........................................................................................................... 43

6.2 WEB USER INTERFACE ..................................................................................................................... 44

Source ............................................................................................................................................... 44

Operation Mode ............................................................................................................................... 45

Stream Mode ................................................................................................................................ 45

Record Mode................................................................................................................................. 50

CG ...................................................................................................................................................... 54

CG Layer ........................................................................................................................................ 54

CG Type ......................................................................................................................................... 55

Location-X ..................................................................................................................................... 55

Location-Y ..................................................................................................................................... 55

Foreground Color .......................................................................................................................... 55

System ............................................................................................................................................... 55

Network Setting ............................................................................................................................ 57

Account and Password .................................................................................................................. 57

Time Setting .................................................................................................................................. 57

Firmware Update .......................................................................................................................... 58

Disk Format ................................................................................................................................... 58

Device Name Setting ..................................................................................................................... 58

Other Option ................................................................................................................................. 59

System Control .............................................................................................................................. 59

Status ................................................................................................................................................ 59

Vertical .............................................................................................................................................. 59

6.3 OPERATIONS.................................................................................................................................. 60

Video Streaming ............................................................................................................................... 60

RTSP/TS/HLS .................................................................................................................................. 60

RTMP ............................................................................................................................................. 65

Text Overlay Video ............................................................................................................................ 66

6.4 RECORD/STREAM PANEL ................................................................................................................. 68

Record Button ................................................................................................................................... 68

Stream Button ................................................................................................................................... 68

Bitrate Button ................................................................................................................................... 69

Vertical Button .................................................................................................................................. 69

6.5 RESTORING FACTORY DEFAULTS ........................................................................................................ 69

6.6 FIRMWARE UPDATE ........................................................................................................................ 69

CHAPTER 7 APPENDICES .............................................................................................................. 70

APPENDIX 1 TALLY OUTPUTS ...................................................................................................................... 70

APPENDIX 2 FIRMWARE UPGRADE ............................................................................................................... 71

Keyboard / Mainboard ..................................................................................................................... 71

Video Streaming Server .................................................................................................................... 73

APPENDIX 3 RECOMMENDED SD CARDS ....................................................................................................... 75

APPENDIX 4 FREQUENTLY-ASKED QUESTIONS ................................................................................................ 77

APPENDIX 5 ETHERNET CABLE SELECTION FOR HDBASET NETWORKS ................................................................ 78

APPENDIX 6 DIMENSIONS .......................................................................................................................... 80

APPENDIX 7 SPECIFICATIONS ...................................................................................................................... 81

SERVICE AND SUPPORT .................................................................................................................. 84

Disclaimer of Product & Services

The information offered in this instruction manual is intended as a guide only. At all times, Datavideo

Technologies will try to give correct, complete and suitable information. However, Datavideo

Technologies cannot exclude that some information in this manual, from time to time, may not be

correct or may be incomplete. This manual may contain typing errors, omissions or incorrect

information. Datavideo Technologies always recommend that you double check the information in

this document for accuracy before making any purchase decision or using the product. Datavideo

Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage

caused by using the information contained within this manual. Further advice on the content of this

manual or on the product can be obtained by contacting your local Datavideo Office or dealer.

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

Warnings and Precautions

1. Read all of these warnings and save them for later reference.

2. Follow all warnings and instructions marked on this unit.

3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

4. Do not use this unit in or near water.

5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious

damage.

6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure

safe and reliable operation of this unit, and to protect it from overheating, do not block or cover

these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation

openings on the bottom of the cabinet will be blocked. This unit should never be placed near or

over a heat register or radiator. This unit should not be placed in a built-in installation unless

proper ventilation is provided.

7. This product should only be operated from the type of power source indicated on the marking

label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo

dealer or your local power company.

8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will

be walked on, rolled over, or otherwise stressed.

9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on

the products plugged into the extension cord do not exceed the extension cord rating.

10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not

exceed 15 amperes.

11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may

touch dangerous voltage points or short out parts that could result in risk of fire or electric shock.

Never spill liquid of any kind onto or into this unit.

12. Except as specifically explained elsewhere in this manual, do not attempt to service this product

yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to

dangerous voltage points or other risks, and will void your warranty. Refer all service issues to

qualified service personnel.

13. Unplug this product from the wall outlet and refer to qualified service personnel under the

following conditions:

a. When the power cord is damaged or frayed;

b. When liquid has spilled into the unit;

c. When the product has been exposed to rain or water;

d. When the product does not operate normally under normal operating conditions. Adjust

only those controls that are covered by the operating instructions in this manual; improper

adjustment of other controls may result in damage to the unit and may often require

extensive work by a qualified technician to restore the unit to normal operation;

e. When the product has been dropped or the cabinet has been damaged;

f. When the product exhibits a distinct change in performance, indicating a need for service.

Warranty

Standard Warranty

 Datavideo equipment are guaranteed against any manufacturing defects for one year from the

date of purchase.

 The original purchase invoice or other documentary evidence should be supplied at the time of

any request for repair under warranty.

 The product warranty period begins on the purchase date. If the purchase date is unknown,

the product warranty period begins on the thirtieth day after shipment from a Datavideo

office.

 All non-Datavideo manufactured products (product without Datavideo logo) have only one

year warranty from the date of purchase.

 Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered

under warranty.

 Viruses and malware infections on the computer systems are not covered under warranty.

 Any errors that are caused by unauthorized third-party software installations, which are not

required by our computer systems, are not covered under warranty.

 All mail or transportation costs including insurance are at the expense of the owner.

 All other claims of any nature are not covered.

 All accessories including headphones, cables, and batteries are not covered under warranty.

 Warranty only valid in the country or region of purchase.

 Your statutory rights are not affected.

Three Year Warranty

 All Datavideo products purchased after July 1st, 2017 are qualified for a

free two years extension to the standard warranty, providing the

product is registered with Datavideo within 30 days of purchase.

 Certain parts with limited lifetime expectancy such as LCD panels, DVD drives, Hard Drive, Solid

State Drive, SD Card, USB Thumb Drive, Lighting, Camera module, PCIe Card are covered for 1

year.

 The three-year warranty must be registered on Datavideo's official website or with your local

Datavideo office or one of its authorized distributors within 30 days of purchase.

Disposal

For EU Customers only - WEEE Marking

This symbol on the product or on its packaging indicates that this product must

not be disposed of with your other household waste. Instead, it is your

responsibility to dispose of your waste equipment by handing it over to a

designated collection point for the recycling of waste electrical and electronic

equipment. The separate collection and recycling of your waste equipment at the

time of disposal will help to conserve natural resources and ensure that it is

recycled in a manner that protects human health and the environment. For more information about

where you can drop off your waste equipment for recycling, please contact your local city office, your

household waste disposal service or the shop where you purchased the product.

CE Marking is the symbol as shown on the left of this page. The letters "CE" are

the abbreviation of French phrase "Conformité Européene" which literally means

"European Conformity". The term initially used was "EC Mark" and it was

officially replaced by "CE Marking" in the Directive 93/68/EEC in 1993. "CE

Marking" is now used in all EU official documents.

Chapter 1 Introduction

Datavideo’s HS-1600T MKII Hand-carry Mobile Switcher, the cutting-edge technology that supports

Full HD 1080P, is designed for broadcast of live events and TV programs with a need for mixing a wide

variety of video and audio sources. The HS-1600T MKII is a highly valuable solution for religion,

education and AV markets.

With its built-in HDBaseT technology, HS-1600T MKII is able to accept the Full HD 1080p video format

from three PTC-150T HDBaseT PTZ Cameras through three individual CAT-6 cables. Each cable runs up

to 100 meters. While shooting in the field, the PoE feature serves to power the three PTC-150T

devices. The PoE feature can also be used in the field where long-distance transmission is required.

The HS-1600T MKII also features an audio mixer with balance XLR inputs and unbalance RCA audio

inputs; more features include PIP, WIPE Generator and Tally.

The HS-1600T MKII has a Joystick that allows the user to Pan, Tilt and Zoom the PTC-150T camera. In

addition, the HS-1600T MKII also allows the user to adjust the PTC-150T’s Focus, IRIS and other

settings.

HS-1600T MKII also features an easy-to-use video streaming and recording device for professional

video producers who need to simultaneously stream a live event and record the master quality

version for post-event editing.

1.1 Features

 Full HD 1080P Video Format

 Built-in HDBaseT technology to connect three PTC-150T HDBaseT PTZ Cameras through three CAT-

6 (or higher) cables with each cable running up to 100 meters.

 PoE technology to Power the PTC-150Ts

 Joystick Pan, Tilt and Zoom with speed control

 Iris, Focus, and Gain Control as well as other PTC-150T camera functions

 Simultaneous Live Streaming & Recording

 Broadcast quality HD / SD H.264 network streaming over RTMP(S), RTSP, TS, and HLS

 Support different bitrates for recording and streaming

 4 Video Inputs (RJ-45 x 3 + HDMI x 1)

 3 Video Outputs (RJ-45 x 1 + HDMI x 2)

 Audio inputs: XLR Analogue x 2 + RCA Analogue (L/R) x 2

 Versatile Mix Effects: PIP, WIPE, Mix and Fades

 Tally Output

 One 17.3-inch monitor with a resolution of 1920x1080

1.2 System Diagram

Chapter 2 Connections and Controls

2.1 Rear Panel

HDBaseT Port IN x 3

AUDIO IN – XLR Balanced CH1/CH2

HDMI Video IN

AUDIO IN – Stereo RCA (Left/Right)

HDBaseT Port OUT x 1

DC IN

HDMI Video OUT x 2

Power Switch

USB F/W Upgrade Port

Stream Port

TALLY Output Port

1. HDBaseT IN

The HDBaseT ports connect three HDBaseT cameras

via three CAT-6 Ethernet cables. Please note that the

baud rate is 38400 and cannot be changed by the

user. Hence, in order to establish connection with

the camera, you will need to set the camera’s baud

rate to 38400. See Section 5.2 for instructions on

setting the baud rate of connected cameras.

If the camera’s baud rate is already pre-set to 38400,

the camera video should appear on the respective

Multiview quadrants as soon as the camera is

physically connected to the HDBaseT port (See

Multiview Screen below).

Note: The HDBaseT port is designed using Neutrik’s

etherCON A series connector system, which is

optimized for pro audio and video network

applications. Prior to using the HS-1600T MKII, you

will need to first acquire the EtherCON A series

connector to make your own Ethernet cable. Please

visit Neutrik’s official home page

(http://www.neutrik.com/) for more information.

2. HDMI Video IN

The HDMI/PC Input port allows connection of an

additional HDMI video source or a PC and the video

or the PC screen will be displayed in the fourth

quadrant of the Multiview (built-in monitor). The

Loop OUT port allows you to connect an additional

monitor for displaying the video source connected or

the PC screen separately.

Multiview Screen

HDBaseT IN 1 (CH1)

HDBaseT IN 2 (CH2)

HDBaseT IN 3 (CH4)

HDMI/PC (CH5)

Note: Please use program source row buttons to select the Program video source and preview

source row buttons to select the Preview video source.

3. HDBaseT OUT

The HDBaseT OUT port allows you to deliver video

directly to HDBaseT devices such as the HBT-11

HDBaseT Receiver Box (Contact your local Datavideo

office or visit our official website for more

information). Note that the maximum video

transmission distance is 60 meters.

4. HDMI Video OUT 2/3

The HDMI Video Out 2/3 output Program video only.

Connect these two ports to HDMI monitors or other

HDMI destination devices.

5. USB F/W Upgrade Port

USB port for firmware upgrade. Please refer to the

Firmware Upgrade section for details.

6. TALLY Output Port

Sends Red and Green tally signals to each channel.

Red indicates On-Air, and Green indicates next

camera source. Tally output port can connect other

Datavideo peripheral devices such as ITC-100, ITC-

200, AM-100 or other monitor models, allowing the

peripheral device to communicate with the HS-1600T

MKII or send tally signal to be displayed on the

monitor.

See Appendix 1 for physical pin connections and

Section 3.5 for Tally Mode selection.

7. Audio Input – XLR Balanced (CH1/CH2)

Two channels of XLR Balanced Audio Input.

8. Audio Input – Stereo RCA (Left/Right)

Connects unbalanced analog audio source (stereo).

9. Power Switch

Power switch ON/OFF

10. DC IN

DC in socket connects the supplied 48V / 190W PSU.

The connection can be secured by screwing the

outer fastening ring of the DC In plug to the socket.

11. Stream Port

The stream port allows the user to establish direct

connection between the notebook computer and the

HS-1600T MKII in order to access the built-in NVS-31

Mark II or connect the NVS-31 Mark II to any local

area network.

Note: See the Chapter 6 Video Streaming for device

configuration and operations.

2.2 Switcher Keyboard Panel

Switcher Settings

Volume Control

Menu browsing buttons

Volume adjustment sliders

RESET button

Headphone jack

User Memory

Audio meter

Shift button

Headphone volume control knob

Transition Effects

Camera Presets

WIPE transition effect selection

Channel Selection Buttons

MIX Enable/Disable button

Preset Buttons

WIPE transition effect Enable/Disable

STR Button

PIP/Keyer

FOCUS / IRIS / White Balance

Enable/Disable buttons for PIP Keyer

Focus Adjustment

Luma Keyer Enable/Disable buttons

IRIS Adjustment

Split Activation button

White Balance

Transition Control

PAN / TILT / ZOOM

T-Bar (manual transition)

Speed Selection Buttons

CUT button

Joystick – PAN/TILT

AUTO transition button

VR Knob – ZOOM

Program/Preview

LOCK Button

Program row

Camera MENU Control

Preview row

MENU Button

ENTER Button

Volume

Control

Program/Preview

Transition Control

Switcher

Settings

PIP/Keyer

Transition

Effects

Camera Presets

Focus / IRS /

White Balance

PAN/TILT/ZOOM

Switcher Settings

Menu browsing buttons

Press the MENU button to gain access to the menu;

use the up/down/left/right arrow buttons to browse

through the menu and press ENTER button to select an

option or MENU button again to exit.

Reset Button

Mode 1 – When in Menu Select mode (left hand

column of the OSD menu), pressing the 'Reset' button

will reset all current menu items to their factory

defaults.

Mode 2 – When in a Sub-Menu, pressing the 'Reset'

button will reset the current menu line only.

User Memory

User Memory buttons 1-3 allow the user to quickly

recall and load previously saved switcher settings with

a single button press. This includes PIP and Keyer

settings. See the User Memory section for setup

information.

Shift Button

Pressing the Shift button will switch USER 1-3 buttons

to USER 4-6 buttons

Transition Effects

WIPE Transition Effect Selection

Each Wipe button consists of black and white colors.

The white represents the current Program image and

the black represents the WIPE-IN image. The HS-1600T

MKII provides 3 WIPE presets with the Horizontal and

Vertical WIPEs selectable on the control panel. The

Center WIPE can be selected from the menu (Start).

Pressing the REV button reverses the direction of the

WIPE.

MIX Enable/Disable Button

A MIX, also known as a dissolve, is a transition wherein

the Program video is replaced by the Preview video at

a smooth rate, and at the same time. Pressing the MIX

button enables the MIX transition effect and

automatically disables the WIPE button. To trigger the

MIX effect, simply press the AUTO button or move the

T-Bar.

WIPE Transition Effect Enable/Disable Button

Pressing the WIPE button enables the WIPE transition

effect after which the WIPE transition effect can be

selected. To trigger the WIPE transition effect, simply

press the AUTO button or move the T-Bar.

Wipe Transition Effect, Border and Position settings

can be found in the OSD menu (Start).

PIP / Keyer

Enable/Disable Buttons for PIP Keyer

Picture in Picture puts the selected Sub Video Source in

a window on the Main Program view, with control over

window size and placement. For PIP configuration,

please refer to the PIP section.

PIP PGM: Shows the configured PIP on the PGM

output after transition, however, the PIP cannot be

previewed on the QUAD split view display.

PIP PVW: Sets the configured PIP on the next

transition. Holding down this button allows selection

of the PIP source from the Preview Source row. The

selected source button will flash.

Luma Keyer Enable/Disable Buttons

Luma Key PGM: Shows the luma key source on the

PGM output and enables the luma key effect,

however, the luma key effect cannot be previewed on

the QUAD split view display.

Luma Key PVW: Enables luma key source for the PGM

output on the next transition. Holding down this

button allows selection of the luma key source from

the Preview Source row. The selected source button

will flash.

See Section 3.4, the Luma Key section, for luma key

configurations.

Split Activation Button

After activating the PIP window, pressing the Split

button will split the PROGRAM output display into two

with the program out view on the left and the PIP view

on the right.

To select the Split source, i.e. the program out view,

please see Split Source in Section 3.2.

Transition Control

T-Bar (Manual Transition)

T-Bar is used for manual transition. The T-Bar can be

either all the way up, all the way down or anywhere in

between. When the T-Bar is pushed to halfway

between the topmost position and the bottommost

position, the keyboard functions will be disabled.

PVW and PGM views can be transitioned at your

preferred speed. To include the transition effect,

simply press the WIPE or MIX button, after which the

Transition Effect will be triggered as you move the T-

Bar.

CUT Button

Pressing the Cut button performs immediate manual

switch between PVW and PGM views without the

transition effect.

AUTO Button

Pressing the Auto button automatically transitions

PVW and PGM views according to the selected speed

and the configured transition effect.

Program Output

Program Source Row

Pressing the number buttons along the PROGRAM row selects the Program video source.

BKG button: Pressing the BKG button will switch the background to a Matte background. The BKG

color can be configured on the OSD MENU(Start  BKG Color). The available color options are listed

as follows:

 White

 Yellow

 Cyan

 Green

 Magenta

 Red

 Blue

 Black

BLK button: Pressing the BLK button places a black screen on the PROGRAM view.

Preview Output

Preview Source Row

Pressing the number buttons along the PREVIEW row selects the Preview video source.

BKG button: Pressing the BKG button will set the Preview OUT to a Matte background, which will be

displayed on the Program OUT monitor upon the next transition. The BKG color can be configured

on the OSD MENU (Start  BKG Color). The available color options are listed as follows:

 White

 Yellow

 Cyan

 Green

 Magenta

 Red

 Blue

 Black

BLK button: Pressing the BLK button sets the Preview OUT to a black screen.

Volume Control

Volume Adjustment Sliders

Sliders to control audio levels for the Main audio

mixer.

Headphone Volume: Audio volume of the connected

headphone.

Master: Main audio output volume.

Headphone Jack

Headphone jack accepts the mini jack plug of the

stereo headphone type. The headphone volume is

controlled by the Headphone volume adjustment

slider.

MASTER OUT Meter

The LED style meters show the audio signal strength at

the Main Program Audio Output. The signal strength is

determined by the level set with the Master OUT

slider. The LEDs turn red at +10 dB to indicate clipping

distortion.

Audio

Volume (dBV)

-20

-10

-8

-4

+10

LED Color

Range (dBV)

-20

-12

-11

-9.5

-8.5

-6.5

-5.5

-3

-2

5.5

6.5

G: Green Y: Yellow R: Red

Camera Presets

Channel Selection Buttons

To control or set up a connected camera, first select it

by pressing these buttons. The selected channel

button will be turned ON.

Preset Buttons

These buttons may be used to store up to four camera

positions for each camera. Each button corresponds to

one stored camera position. The button LED will be

turned ON when selected.

STR Button

Pressing this button enters the HS-1600T MKII into

STORE MODE. When activated, this allows the current

camera position to be stored in a chosen Channel

Preset Button by pressing the corresponding preset

button.

Press again to exit STORE MODE.

FOCUS / IRIS / White Balance

Focus Adjustment

To manually control the FOCUS setting, first press the

MANUAL button to enter the manual mode. The

button LED will be turned ON to indicate that the

manual mode is enabled.

The FOCUS dial can then be rotated to set the focus.

If the MANUAL button is disabled (OFF), the camera is

in AUTO FOCUS mode.

IRIS Adjustment

To manually control the IRIS setting, first press the

MANUAL button to enter the manual mode. The

button LED will be turned ON to indicate that the

manual mode is enabled.

The IRIS dial can then be rotated to set the exposure.

If the MANUAL button is disabled (OFF), the camera is

in AUTO IRIS mode.

White Balance

Certain light conditions can cause discoloration of your

image. White balance allows you to adjust the color

balance in order to produce the best image quality.

Push Auto

The One Push White Balance mode is a fixed white

balance mode that is automatically adjusted at the

user’s request. The One Push White Balance data is

lost when the power is turned off, in other words,

turning off the machine power resets the One Push

White Balance setting.

The One Push White Balance mode can also be used

for white balance calibration. Zoom in the camera lens

on a white piece of paper which basically serves as a

reference for what is white, then press the PUSH AUTO

button to balance other colors accordingly.

Note: If you are using the HS-1600T in conjunction

with the PTC-140T, after the PUSH AUTO key is

pushed, wait for 5 to 6 seconds while the camera

adjusts the white balance setting automatically then

proceed to the next action.

MWB (Manual White Balance)

Push to enable manual white balance adjustment.

ATW (Automatic White Balance)

Push to enable automatic white balance adjustment.

PAN / TILT / ZOOM

Speed Selection Buttons

The speed at which the selected camera moves can be

chosen by pressing one of the three speed buttons.

Joystick – PAN / TILT

PAN – Move the joystick left or right to pan the

selected PTZ camera from left to right or vice versa.

TILT – Move the joystick up or down to tilt the selected

PTZ camera up or down.

Note: Before attempting to use the joystick to PAN or

TILT a selected camera, first make sure the LOCK

button is not enabled. If the LOCK button LED is ON,

the joystick is locked; press the LOCK button to unlock

the joystick.

VR Knob – ZOOM

ZOOM – Twist the joystick clockwise (to the right) or

anti-clockwise (to the left) to have the selected PTZ

camera zoom in or out.

Note: Make sure the LOCK button is not enabled. If the

LOCK button LED is ON, the joystick is locked; press the

LOCK button to unlock the joystick.

LOCK Button

When enabled, the joystick will be in the lock state. To

resume its functional status, simply press the button

once to unlock the joystick.

Page is loading ...

DataVideo HS-1600T Mark II User manual

Brand: DataVideo

Model: HS-1600T Mark II

Category: Supplementary music equipment

Type: User manual

Download PDF

report

DataVideo HS-1600T Mark II User manual

DataVideo HS-1600T Mark II User manual

Related papers

Other documents