GUARDINATOR
Vehicle Management Solution (VMS)
GUARDINATOR VMS is a registered Digital and software based virtual assistant that
integrates Honeywell's advanced professional vehicle analysis technology and
provides a series of vehicle-related auxiliary services for private vehicle users
(currently not for heavy duty or specialty vehicles).
GUARDINATOR VMS has below excited features:
Intelligent Optical Heads up display (HUD) with direct projection of
smartphone dashboards *
Smart Splitview technology to enable extended Display between HUD and
smartphone *
Quick reading and interpretation of Vehicle Sensors *
Real-time data analysis and display of vehicle sensors *
Real time fuel consumption simulation *
Tire pressure and temperature (TP)monitoring *
Diagnostic trouble code(DTC) solution (depends Electronic Control
Unit(ECU)) *
Featured Driving dashboard for multiple deployment environment
Easier navigation and cellphone flashlight
Support wireless charging with smart bracket * (Depends on smartphone
capability)
On-going update and upgrade of the newest technology
(*) Purchase of separate hardware is required to enable the full function
Vehicle compatibility:
Y="Yes", N="NO", "N/C"="No correlation"
Function
Gasoline Fuel
Diesel
Fuel
Other
fuel
On Board Diagnose (OBD)
OBD II/EOBD **
N
N
Tire Monitor
Y
Y
Y
Wireless Charging Bracket
Y
Y
Y
Dashboard
N/C
N/C
N/C
HUD
N/C
N/C
N/C
Splitview
N/C
N/C
N/C
navigation &cellphone
flashlight
N/C
N/C
N/C
Diagnostic trouble
Y
N
N
Function
Gasoline Fuel
Diesel
Fuel
Other
fuel
code(DTC)
**It is highly recommended to deploy into vehicles that manufactured after year
2008 and support OBD II/EOBD standard. Vehicles manufactured after year 2012
would have a relatively better compatibility. Due to versatility of the vehicles,
Honeywell does not guarantee 100% compatibility even the vehicle meets OBD
II/EOBD standard. Please consult your technician or vehicle manual for the vehicle’
s OBD information before the purchase of GUARDIATOR.
The Vehicle must be equipped with a standard OBD port to enable the proper use
on the OBD function.
Internet access (either via local carrier WWAN or local WLAN) is required to be
enabled on the smartphone to activate the OBD and TP license.
Bluetooth is required to be enabled on the smartphone for OBD and TP
connection.
WIFI is required to be enabled on your smartphone for HUD or HUD split view
function.
End user license and service
Due to the particularity of software and service products, the hardware of
GUARDINATOR VMS, such as On Board Diagnose (OBD) and tire pressure
equipment (TP), is supposed to be in use once activated in GUARDINATOR VMS.
Hardware, such as OBD TP and HUD, are not guaranteed for damage caused
by human factors, fluid, dampness and misuse or products that are modified
or disassembled by the user or non-certified third party . Failures caused by
self-cracking or self-upgrading are not guaranteed on warranty.
Data Services
GUARDINATOR VMS only provides read-only operation for automobile data
and does not have the functions of "writing" and "modifying" automobile
related parameters without end user’s confirmation.
Different sensors in automobile will affect the actual use of GUARDINATOR
VMS. If the APP interface shows "N/A" or "Unsupported PID", it indicates that
the relevant sensors are not mounted in the relevant parts of the current
vehicle or sensor data is unreadable/unavailable.
It is not recommended to operate relevant function in driving. It is
suggested that you operate the GUARDINATOR VMS only after the vehicle has
stopped and make sure the surrounding area is safe.
Disclaimer
It is dangerous to operate the mobile phones or watch the screen or HUD virtual
interface for a long time when driving. The driver/user shall take full responsibility
for any adverse consequences arising therefrom. Software and hardware
manufacturers are not subject to the relevant responsibilities. Drivers/User should
drive safely and comply with all relevant regulations.
Privacy Protection
Honeywell International Inc. (“Company”, “our”, “us”, or “we”),the "data
controller" of the personal information we collect about you pursuant to this
Privacy Statement, is committed to protecting your privacy. This Privacy Statement
details the steps we take to protect your personal information when you visit any of
our websites or applications that contain a link to this Privacy Statement
(collectively, our “Sites”) or when you contact us. It describes how we process
personal information relating to you, including the types of personal information
that we collect, the purposes for which we use it, the types of third parties with
which we share it, and any rights you may have with respect to such information.
Personal information is information, or a combination of pieces of information, that
allow you to be identified.
IMPORTANT NOTICE FOR RESIDENTS OF THE EUROPEAN ECONOMIC AREA (EEA) :
EEA RESIDENTS MAY BE ENTITLED TO OBJECT TO CERTAIN TYPES OF PROCESSING
ACTIVITIES INVOLVING YOUR PERSONAL INFORMATION DESCRIBED IN THIS
PRIVACY STATEMENT, INCLUDING WHERE WE ARE RELYING ON A LEGITIMATE
INTEREST TO PROCESS YOUR PERSONAL INFORMATION OR WHERE WE ARE
PROCESSING YOUR PERSONAL INFORMATION FOR DIRECT MARKETING. IN SOME
CASES, WE MAY DEMONSTRATE THAT WE HAVE COMPELLING LEGITIMATE
GROUNDS TO CONTINUE TO PROCESS YOUR PERSONAL INFORMATION IN
WHICH CASE WE ARE NOT OBLIGED TO COMPLY WITH YOUR REQUEST.
Privacy statement detail can be found at
https://www.honeywell.com/privacy-statement
Honeywell GUARDINATOR VMS does not collect any personal related data, but it
may use location and navigation based information to enable the heads up display
(HUD).
Users are required to purchase a valid licensed product to enable the application of
the software. The licensed activation code will be validated remotely via Honeywell
to enable the function of the product (data roaming or connection required during
validation).
Guide:
√ How to Install GUARDINATOR VMS into smartphone
√ How to Install OBD into the Vehicle
√ How to Install TP into the Vehicle
√ How to Activate OBD into GUARDINATOR VMS
√ How to Activate TP into GUARDINATOR VMS
√ How to use GUARDINATOR VMS OBD DATA functions
√ How to use GUARDINATOR VMS Dashboard functions
√ How to use GUARDINATOR VMS Solar Display Terminal
√ FLEX Series Phone bracket
√ FLEX AIR Series Wireless Charging phone bracket
How to Install GUARDINATOR VMS into
smartphone
The GUARDINATOR VMS App requires your phone to support the following
operating systems:
Apple®： iOS version 9.0 or above, iPhone 6 or above.
Android™ System： Support/compatible with Android Version 6.0 or above.
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. Android is a registered
trademark of Google.
iPhone: Search GUARDINATOR in App Store and install it.
Android: Search GUARDINATOR in GOOGLE Play Store and install it.
The GUARDINATOR VMS requires the smartphone to turn on internet access via
your local carrier to activate the OBD and TP license.
The GUARDINATOR VMS requires the smartphone to turn on Bluetooth for OBD
and TP function.
The GUARDINATOR VMS requires the smartphone to turn on WIFI for HUD or HUD
split view function.
How to Install OBD into the Vehicle
Note: Only GUARDINATOR VMS certified OBD device can be recognized and
activated.
Step #1: Take out the OBD( one QR code on the back). Note that this QRcode
contains encrypted serial numbers for both association and activation, please keep
it in a safe place.
Every serial number (activation code) can only be valid for one-time activation
and gets expired once the activation completed successfully. Resale or
re-activation is not supported.
Step #2: You can find the corresponding on-board diagnostics data port in your
vehicle. Most OBD port of vehicles are located in the lower left side of the
dashboard on the driver's side (above the driver's left leg). Some are located under
the steering wheel or above the brake pedal. Some cars have a lid that needs to be
opened. Others require an outward extension cord before they can be used. the
commonly used port can be found in the vehicle manual or you can google search
the right position. Normally it is a 16-pin port .Please note that the port is made
into special shapes in order to prevent wrong insertion. Please check the direction
before installation.
Step #3: Connect the OBD into the port of the vehicle according to the correct
direction and ensure that the connection is firm (loose or inadequate contact may
cause failure).Note: To use complete software application you must turn on the
Bluetooth on your mobile phone so that it can be connected to the OBD (at the
same time, please power on the vehicle).
Please remove the OBD from the port if the vehicle is not in use for more than 10
days to save the battery.
How to Install TP into the Vehicle
Each tire is equipped with an independent wireless sensor. Please install according
to the indication position of the sensor. Incorrect installation may result in failure or
misfunction.
You can also seek service from your vehicle maintenance service provider.
If the data cannot be read properly after installation, please drive the car for more
than 5 minutes to activate the data transition. (the current TP is with Low power
design and the sensor will not transmit data in real time without obvious tire
variance (< 1% ))
How to Activate OBD into GUARDINATOR
VMS
Open GUARDINATOR VMS, click <SETUP> tab on the bottom of the screen.
Click the red rectangle <SCAN TO ACTIVATE> on the top of the screen to associate
or activate the OBD device.
Scanning the QR code pasted on the OBD hardware to activate. Once the activation
is successful, a list of active OBDs shows in the Guardinator OBD list.
Note: Each OBD serial number can only be activated by one mobile phone. If
the user changes the phone or resets the IMEI motherboard number, it needs
to order a new OBD Activation License.
If the scan of QR code is unsuccessful, please click <Guardinator OBD> menu.
Then click <SELECT DEVICE> button.
Select Manual input device code as following picture. Please enter the 12-bit serial
number printed on the OBD and click CONFIRM to complete the activation.
How to Activate TP into GUARDINATOR VMS
Open GUARDINATOR VMS, click <SETUP> tab on the bottom of the screen.
Click the red rectangle <SCAN TO ACTIVATE> on the top of the screen to activate
the TP.
Scanning the TP QR code from the package box. Once the activation is successful,
each tire position will show activated with dark blue background as follows:
Note: The QR code serial number of the tire sensor is printed into a card in the
package box, please keep the card in a safe place. If lost, it will affect the activation
and use of the tire sensor.
Note: Each tire pressure serial number can only be activated by one mobile
phone. If the user changes the phone or resets the IMEI motherboard number,
it requires to order a new tire pressure Activation License.
GUARDINATOR VMS does not display valid values in the case of incorrect
installation of tire pressure equipment.
Tire Pressure Setting
According to the tire parameters of different manufacturers and the use scenarios,
users can define the upper and lower limits of tire pressure alarm.
TP will transmit the real time data when the change of tire pressure, temperature
and other data are monitored.
How to use GUARDINATOR VMS OBD DATA
functions
Once the OBD is valid and activated, you can start to use the functions:
Click <DATA> tab on the bottom of the screen.
Then Click <All Sensors>.
When the OBD device is connected, it will display the data and unit information of
each instruction supported by the current vehicle. Note: please make sure OBD
connection is valid and the vehicle is powered on. Sometime it will take a while for
OBD to communicate with the vehicle.
Due to the massive sensors in vehicle, it may need to scroll up and down the
interface to find the data information of instruction data item of relevant names.
When the name of the instruction data item is found, hold for 3 seconds, the
interface will automatically display the data of all instruction data items contained
in the current interface. If the vehicle is not equipped with the sensor or the sensor
is unreadable/not open, N/A will be displayed.
Live Data
Click <DATA> tab on the bottom of the screen.
Then Click <Live Data>.
After selecting a data item, when the vehicle is equipped with the corresponding
sensor and supports the instruction data item, it will display the data diagram as
below picture.
If the vehicle does not support data items selected by user, <Unsupported PID> or
<sensor N/A> will be displayed at the bottom of the screen.
How to use GUARDINATOR VMS Dashboard
functions
Head Up Display
Open GUARDINATOR VMS, click <HUD> tab on the bottom of the screen.
Click <Head Up Display> as follows:
In order to correctly display the fuel consumption information of the vehicle's
current trip, please confirm that the displacement value is corrected and
corresponding to the vehicle when adding a new car in the app. Incorrect
displacement input will lead to variance of the calculation.
After entering the functionality, the HUD interface will start calculating the fuel
consumption taking it as the starting point of the trip.
HUD interface will display below information:
Instantaneous fuel consumption (it requires users to set correct engine
displacement information);
Current trip fuel consumption (it requires users to set correct engine
displacement information);
Average fuel consumption (it requires users to set correct engine
displacement information);
Engine speed (it requires users to install and activate OBD device);
Vehicle speed (it requires users to install and activate OBD device);
Tire Pressure (it requires to install and activate tire pressure device);
When the user installs and activates the tire pressure device in the current vehicle,
the information related to tire pressure will be displayed on the HUD interface,
which ensures that the user can understand the tire pressure condition while
driving through observing the HUD. It will improve driving safety.
Note: Fuel consumption simulation is for reference only due to the complexity and
variety of the sensors and calculation. Normally a 5% to 15% tolerance range can
be expected.
The green circle on the above picture indicates that the tire pressure at the current
position is normal. The tire in the upper right position needs to be inflated because
the tire pressure is less than the set value, so it will display Pump up to prompt the
user that the tire pressure in the upper right position is low and needs to be
inflated.
When there is a leaking tire, it will be displayed immediately in HUD mode and
warn the user with red “Leaking”. In the picture above, the left front tire, left rear
tire and right rear tire are leaking, the car needs to be stopped for further checking
to ensure driving safety.
If the tire pressure device is not correctly installed onto the vehicle, please refer to
the installation of tire pressure (TP).
If the tire pressure device is not activated, please refer to the activation of tire
pressure (TP).
This feature can project the HUD data displayed in App onto HUD hardware.
You can also scroll right or left to switch to different dashboard(not Available in
iPhone at this moment).
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
