George Kovacs P574-084-L User manual

Brand
George Kovacs
Model
P574-084-L
Type
User manual

This manual is also suitable for

]
IMPORTANT: Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with LED compatible wall dimmer
switches.
INSTALLATION INSTRUCTIONS FOR P574/P575-084-L
For LED Bath Vanity (New. 2019/02/11)
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVE RT I SS E ME N T ! CO U P E R L E C O U RA NT A U N I V E AU D E S FU S I B L E S O U D O D I SJ O N C TE U R .
AV E R T I S S E M E NT ! C O U P E R L E C O U R A N T A U N I V E AU D E S F US I B L E S OU D O D I S J O N C T E U R .
PREPARATION
1. Shut off power at the fuse box or circuit breaker box. If
necessary remove the old fixture and mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
in a clear area. Take care not to lose any small parts
necessary for installation.
INSTALLING GLASS (FIG. 3)
3. Insert glass shade (H) into the base plate (L), install end
cap (G) by screws (F) and gasket (M). Gasket (M) should
insert between base plate (L) and end cap (G).
MOUNTING THE FIXTURE (FIG. 1)
4. Secure mounting plate (C) to junction box (A) using
junction boxes screws (B) (Size: #8-32*0. 5"L). The side of
the mounting plate marked “ GND” must face out as
picture.
CONNECTING THE WIRES (FIG. 2)
5. At this point, connect the electrical wires as shown in Fig. 2,
making sure that all wire connectors are secured. If your
outlet has a ground wire (green or bare copper), connect
the fixtures ground wire to it. Otherwise, connect the fixture
ground wire directly to the mounting plate (C) using the
green screw provided. After wires are connected, tuck
them carefully inside the junction box.
FINISHING THE INSTALLATION (FIG.1)
6. Fix the vanity fixture (E) to the mounting plate (C) by using
screws (D).
Your installation is now completed. Return power to the junction box
and test the fixture.
CAUTION /ATTENTION: When handling the fixture, do not
apply pressure to the glass and the single ring in middle. Hold
the fixture by the base only.
Replacing Glass shade and LED module (Fig. 3)
The glass shade and LED module can be replaced by a
qualified electrician without cutting of wire and without damage
to any decorative element to which the fixture is attached. See
installation steps for more details (Fig 3.)
a. Shut off power. Remove the fixture from the wall.
b. Loosen screws (F) and get down decorative caps (G) from
both sides.
c. Remove the Glass shade (H) from the base plate (L).
d. Pull back the power leads (I) via pre-drilled hole of the base
plate (L) and screw down the screws (K) from both sides.
e. Remove the LED module (J) from base plate (L).
f. Reverse steps a-c for installing new Glass shade and
reverse steps a-e for installing new LED module.
Note: The glass and LED module should be provided by a
specified supplier.
Note: Illustration (Fig. 1& Fig. 3) on this manual is for
installation purposes only. It may or may not be identical to
the fixture purchased.
FIG.1
Set #A-020-113
- Mounting plate*1
- Ground screw*1
- Mounting screw*2
Fig 3
Fig.2
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
LA-3089E
  • Page 1 1

George Kovacs P574-084-L User manual

Brand
George Kovacs
Model
P574-084-L
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents