Evo Control 13 Series Owner's manual

1

This series of heat pump unit owns following features:

1 Advanced controlling

The PC microcomputer based controller is available for the users to review or set the

running parameters of the heat pump. Centralized controlling system can control several

units by PC.

2 Nice appearance

The heat pump is designed with beautiful looking. The monobloc one has the water

pump included which is very easy for installation.

3 Flexible installation

The unit has smart structure with compact body, just simple outdoor installation is

needed.

4 Quiet running

High quality and efficient compressor, fan and water pump is used to ensure the low

noise level with insulation.

5 Good heat exchange rate

The heat pump unit use special designed heat exchanger to enhance whole efficiency.

6 Large working range

This series of heat pump is designed to work under different working conditions as low

as -15 degrees for heating.

It is vital that the below instructions are adhered to at all times to keep the warranty.

The unit can only be opened or repaired by qualified installer or an authorised dealer.

Maintenance and operation must be carried out according to the recommended time

and frequency, as stated in this manual.

Use genuine standard spare parts only.

—

Air source water chiller and heat pump is a kind of high efficiency, energy saving and

environment friendly equipment, which is mainly used for house warming. It can work

with any kind of indoor unit such fan coil, radiator, or floor heating pipe, by provide warm

or hot water. One unit of monobloc heat pump can also work with several indoor units. The

air source water heat pump unit is designed to have heat recovery by using super

heater which can provide hot water for sanitary purpose.

In order to provide the customers with high quality, strong reliability and good versatility

product, this heat pump is produced by strict design and manufacture standards.

This manual includes all the necessary information about installation, debugging,

discharging and maintenance. Please read this manual carefully before you open or

maintain the unit. The manufacture of this product will not be held responsible if someone

is injured or the unit is damaged, as a result of improper installation, debugging,

unnecessary maintenance which is not in line with this manual. The unit must be installed

by qualified personnel.

Preface

CONTENT

1 Preface

2 Safety Precaution

(1) Mark notes

(2) Icon Notes

(3) Warning

(4) Attention

3 Specification

(1) Appearance and Structure of the heat pump

(2) Specification data

(3) Unit Dimension

4 Installation

(1) Application of heat pump

(2) Choose a right heat pump unit

(3) Installation place

(4) Installation method

(5) Water loop connection

(6) Power supply connection

(7) Location of the unit

(8) Transit

(9) Trial Running

5 Usage

(1) Function of wire controller

(2) Usage of wire controller

6 Maintenance

(1) Maintenance

(2) Ordinary malfunctions and solution

7 Appendix

(1) Appendix 1

(2) Appendix 2

(3) Appendix 3

(4) Appendix 4

(5) Appendix 5

(6) Appendix 6

(7) Appendix 7

(8) Appendix 8

1

2

3

4

5

6

7

8

9

10

11

12

13

20

21

23

24

25

26

27

28

29

1

The unit can only be opened or repaired by qualified installer or an authorised dealer.

Maintenance and operation must be carried out according to the recommended time

and frequency, as stated in this manual.

Use genuine standard spare parts only.

—

The Evo Control 13 is a kind of high efficiency, energy saving and environmentally friendly

equipment, which is mainly used for house warming. It can work with any kind of indoor unit such

fan coil, radiator, or floor heating pipe, by provide warm or hot water. One unit of monobloc heat

pump can also work with several indoor units. The air source water heat pump unit is designed to

have heat recovery by using super heater which can provide hot water for sanitary purpose.

This series of heat pump unit owns following features:

1 Advanced controlling

The PC microcomputer based controller is available for the users to review or set the running

parameters of the heat pump. Centralized controlling system can control several units by PC.

2 Nice appearance

The heat pump is designed with aesthetics in mind. The monobloc one has the water pump

included which is very easy for installation.

3 Flexible installation

The unit has smart structure with compact body, just simple outdoor installation is needed.

4 Quiet running

High quality and efficient compressor, fan and water pump is used to ensure the low noise

level with insulation.

5 Good heat exchange rate

The heat pump unit uses speciaially designed heat exchanger to enhance whole efficiency.

6 Large working range

This series of heat pump is designed to work under different working conditions as low as -15

degrees for heating.

In order to provide the customers with high quality, strong reliability and good versatility

product, this heat pump is produced by strict design and manufacture standards.

This manual includes all the necessary information about installation, debugging,

discharging and maintenance. Please read this manual carefully before you open or maintain the

unit. The manufacturer of this product will not be held responsible if someone is injured or the

unit is damaged, as a result of improper installation, debugging, unnecessary maintenance

which is not in line with this manual.

The unit must be installed by qualified personnel.

It is vital that the below instructions are adhered to at all times to keep the warranty.

Preface

CONTENT

1 Preface

2 Safety Precaution

(1) Mark notes

(2) Icon Notes

(3) Warning

(4) Attention

3 Specification

(1) Appearance and Structure of the heat pump

(2) Specification data

(3) Unit Dimension

4 Installation

(1) Application of heat pump

(2) Choose a right heat pump unit

(3) Installation place

(4) Installation method

(5) Water loop connection

(6) Power supply connection

(7) Location of the unit

(8) Transit

(9) Trial Running

5 Usage

(1) Function of wire controller

(2) Usage of wire controller

6 Maintenance

(1) Maintenance

(2) Ordinary malfunctions and solution

7 Appendix

(1) Appendix 1

(2) Appendix 2

(3) Appendix 3

(4) Appendix 4

(5) Appendix 5

(6) Appendix 6

(7) Appendix 7

(8) Appendix 8

1

2

3

4

5

6

7

8

9

10

11

12

13

20

21

23

24

25

26

27

28

29

3

安装前注意事项

The heat pump must be installed by qualified personals,

to avoid improper installation which can lead to water

leakage, electrical shock or fire.

Please make sure that the unit and power connection

have good earthing, otherwise may cause electrical shock.

Installation

Professional installer

is required.

Earthing is required

Warning

Meaning

Operation

Meaning

PROHIBITION

Shut off the power

DO NOT put fingers or others into the fans and evaporator

of the unit, otherwise harm may be occurred.

When there is something wrong or strange smell, the power

supply need to be shut off to stop the unit. Continue to run

may cause electrical short or fire.

Move and repair

Entrust

Prohibit

Entrust

When the heat pump need to be moved or installed again,

please entrust dealer or qualified person to carry it out.

Improper installation will lead to water leakage, electrical

shock, injury or fire.

It is prohibited to repair the unit by the user himself, otherwise

electrical shock or fire may be occur.

When the heat pump need to be repaired, please entrust

dealer or qualified person to carry it out. Improper movement

or repair on the unit will lead to water leakage, electrical

shock, injury or fire.

Meaning

Safety Precaution

2

To prevent the users and others from the harm of this unit, and avoid damage on the

unit or other property, and use the heat pump properly, please read this manual carefully

and understand the following information correctly.

Safety Precaution

Mark

Meaning

A wrong operation may lead to death or heavy injury on people.

A wrong operation may lead to harm on people or loss of material.

Mark Notes

WARNING

ATTENTION

Icon

Meaning

Prohibition. What is prohibited will be nearby this icon

Compulsory implement. The listed action need to be taken.

ATTENTION (include WARNING)

Please pay attention to what is indicated.

Icon notes

3

安装前注意事项

The heat pump must be installed by qualified personals,

to avoid improper installation which can lead to water

leakage, electrical shock or fire.

Please make sure that the unit and power connection

have good earthing, otherwise may cause electrical shock.

Installation

Professional installer

is required.

Earthing is required

Warning

Meaning

Operation

Meaning

PROHIBITION

Shut off the power

DO NOT put fingers or others into the fans and evaporator

of the unit, otherwise harm may be occurred.

When there is something wrong or strange smell, the power

supply need to be shut off to stop the unit. Continue to run

may cause electrical short or fire.

Move and repair

Entrust

Prohibit

Entrust

When the heat pump need to be moved or installed again,

please entrust dealer or qualified person to carry it out.

Improper installation will lead to water leakage, electrical

shock, injury or fire.

It is prohibited to repair the unit by the user himself, otherwise

electrical shock or fire may be occur.

When the heat pump need to be repaired, please entrust

dealer or qualified person to carry it out. Improper movement

or repair on the unit will lead to water leakage, electrical

shock, injury or fire.

Meaning

Safety Precaution

2

To prevent the users and others from the harm of this unit, and avoid damage on the

unit or other property, and use the heat pump properly, please read this manual carefully

and understand the following information correctly.

Safety Precaution

Mark

Meaning

A wrong operation may lead to death or heavy injury on people.

A wrong operation may lead to harm on people or loss of material.

Mark Notes

WARNING

ATTENTION

Icon

Meaning

Prohibition. What is prohibited will be nearby this icon

Compulsory implement. The listed action need to be taken.

ATTENTION (include WARNING)

Please pay attention to what is indicated.

Icon notes

4

Switch off

the power

Prohibition

Please switch off the power for clean or maintenance.

It is prohibited to use copper or iron as fuse. The right fuse

must be fixed by electrician for the heat pump.

It is prohibited to spray the flammable gas to the heat pump,

as it may cause fire.

Installation

Operation

Prohibition

安装前注意事项

ATTENTION

Check the

installation basement

Please check the installation basement in a period (one month),

to avoid any decline or damage on the basement, which may

hurt people or damage the unit

Safety Precaution

Meaning

Fix the unit

Installation Place

Need

circuit breaker

The unit CANNOT be installed near the flammable gas.

Once there is any leakage of the gas, fire can be occur.

Make sure that the basement of the heat pump is strong

enough, to avoid any decline or fall down of the unit

Make sure that there is circuit breaker for the unit, lack of

circuit breaker can lead to electrical shock or fire.

Meaning

5

Specification

1 Appearance and structure of the unit：

The maximum cable for the wire

controller is 200 metres from the heat pump.

Circulating fan

(side discharge)

Water inlet

Wire

controller

Water outlet

4

Switch off

the power

Prohibition

Please switch off the power for clean or maintenance.

It is prohibited to use copper or iron as fuse. The right fuse

must be fixed by electrician for the heat pump.

It is prohibited to spray the flammable gas to the heat pump,

as it may cause fire.

Installation

Operation

Prohibition

安装前注意事项

ATTENTION

Check the

installation basement

Please check the installation basement in a period (one month),

to avoid any decline or damage on the basement, which may

hurt people or damage the unit

Safety Precaution

Meaning

Fix the unit

Installation Place

Need

circuit breaker

The unit CANNOT be installed near the flammable gas.

Once there is any leakage of the gas, fire can be occur.

Make sure that the basement of the heat pump is strong

enough, to avoid any decline or fall down of the unit

Make sure that there is circuit breaker for the unit, lack of

circuit breaker can lead to electrical shock or fire.

Meaning

5

Specification

1 Appearance and structure of the unit：

The maximum cable for the wire

controller is 200 metres from the heat pump.

Circulating fan

(side discharge)

Water inlet

Wire

controller

Water outlet

7

3 Unit dimension

Model: HH13

Specification

Water inlet

Drainage

Water outlet

6

2. The data of unit

Specification

Unit Model

Cooling Capacity

Heating Capacity

Cooling Power Input

Heating Power Input

Running Current(Cooling/Heating)

Power Supply

Compressor Quantity

Compressor

Fan Quantity

Fan Power Input

Fan rotate speed

Noise

Water Pump Input

Water head

Water Connection

Water Flow Volume

Water Pressure Drop

Unit Net Dimensions(L/W/H)

Unit Shipping Dimensions(L/W/H)

Net Weight

Shipping Weight

Cooling: temperature:35℃/24℃,Inlet/Outlet water temperature:12℃/7℃

Heating: temperature:7℃/6℃,Inlet/Outlet water temperature:30℃/35℃

(Above information just for your reference, Please subject to nameplate on the unit）

Ambient

See the drawing of the units

See package label

See nameplate

Evo Control 13

10.0

34000

13.0

44000

3.5

3.1

15.2/13.5

2

Rotary

2

120×2

850

56

0.2

10

1

1.7

34

230V~/50Hz

kW

BTU/h

kW

BTU/h

kW

A

W

RPM

dB(A)

kW

m

inch

3

m /h

kPa

mm

kg

Super heater access

7

3 Unit dimension

Model: Evo Control 13

Specification

Water inlet

Drainage

Water outlet

6

2. The data of unit

Specification

Unit Model

Cooling Capacity

Heating Capacity

Cooling Power Input

Heating Power Input

Running Current(Cooling/Heating)

Power Supply

Compressor Quantity

Compressor

Fan Quantity

Fan Power Input

Fan rotate speed

Noise

Water Pump Input

Water head

Water Connection

Water Flow Volume

Water Pressure Drop

Unit Net Dimensions(L/W/H)

Unit Shipping Dimensions(L/W/H)

Net Weight

Shipping Weight

Cooling: temperature:35℃/24℃,Inlet/Outlet water temperature:12℃/7℃

Heating: temperature:7℃/6℃,Inlet/Outlet water temperature:30℃/35℃

(Above information just for your reference, Please subject to nameplate on the unit）

Ambient

See the drawing of the units

See package label

See nameplate

HH13

10.0

34000

13.0

44000

3.5

3.1

15.2/13.5

2

Rotary

2

120×2

850

56

0.2

10

1

1.7

34

230V~/50Hz

kW

BTU/h

kW

BTU/h

kW

A

W

RPM

dB(A)

kW

m

inch

3

m /h

kPa

mm

kg

Super heater access

8

Installation

1.2 Air-con and super heater(for hot water)

Sanitary water

Water tank

WATER COUPLING

AUTOMATIC AIR VENT

CHECK-VALVE FOR WATER

FLEXIBLE CONNECTION FOR WATER

DIRTY DRAIN

WATER THERMOMETER

WATER PRESSURE METER

WATER FILTER

1 Application of heat pump

1.1 Only for air-con

WATER COUPLING

AUTOMATIC AIR VENT

CHECK-VALVE FOR WATER

FLEXIBLE CONNECTION FOR WATER

DIRTY DRAIN

WATER THERMOMETER

WATER PRESSURE METER

WATER FILTER

9

4 Installation method

The heat pump can be installed onto the concrete basement by expansion screws, or

onto a steel frame with rubber feet which can be placed on the ground or housetop.

Make sure that the unit is placed horizontally.

2 Choose a right heat pump unit

2.1 Based on the local climate condition, construction features and insulation level,

calculate the required cooling(heating) capacity per square meter.

2.2 Conclude the total capacity which will be needed by the construction.

2.3 According to the total capacity needed, choose the right model by consulting the heat.

pump features as below:

Heat pump features

Cooling only unit： chilled water outlet temp. at 5-15 , maximum ambient temp. at 43 .

Heating and Cooling unit for cooling chilled water outlet temp. at 5-15 ,maximum

ambient temp. at 43 . For heating, warm water inlet temp. at 40-50 , minimum ambient

temp. at -10 .

℃ ℃

： ℃

℃ ℃

℃

Unit application

Air source water chiller and heat pump is used for house, office, hotel, and so forth, which

need heating or cooling separately, with each area need to be controlled.

There must be enough space around the unit for maintenance.

The place is free from heat radiation and other fire flame.

There must be not obstacles near the air inlet and outlet of the heat pump.

A place which is free from strong air blowing.

There must be water channel around the heat pump to drain the condensing water .

The location must have good ventilation.

The unit can be installed on any place outdoor which can carry heavy machine such

as terrace, housetop, ground and so on.

A pall is needed in winter to protect the heat pump from snow.

3 Installation place

Installation

8

Installation

1.2 Air-con and super heater(for hot water)

Sanitary water

Water tank

WATER COUPLING

AUTOMATIC AIR VENT

CHECK-VALVE FOR WATER

FLEXIBLE CONNECTION FOR WATER

DIRTY DRAIN

WATER THERMOMETER

WATER PRESSURE METER

WATER FILTER

1 Application of heat pump

1.1 Only for air-con

WATER COUPLING

AUTOMATIC AIR VENT

CHECK-VALVE FOR WATER

FLEXIBLE CONNECTION FOR WATER

DIRTY DRAIN

WATER THERMOMETER

WATER PRESSURE METER

WATER FILTER

9

4 Installation method

The heat pump can be installed onto the concrete basement by expansion screws, or

onto a steel frame with rubber feet which can be placed on the ground or housetop.

Make sure that the unit is placed horizontally.

2 Choose the right heat pump unit

2.1 Based on the local climate condition, construction features and insulation level,

calculate the required cooling(heating) capacity per square meter.

2.2 Conclude the total capacity which will be needed by the construction.

2.3 According to the total capacity needed, choose the right model by consulting the heat.

pump features as below:

Heat pump features

Cooling only unit： chilled water outlet temp. at 5-15 , maximum ambient temp. at 43 .

Heating and Cooling unit for cooling chilled water outlet temp. at 5-15 ,maximum

℃ ℃

： ℃

℃

ambient temp. at 43 . For heating, warm water inlet temp. at 40-50

℃

, minimum ambient

temp. at -10

℃

.

Unit application

Air source water chiller and heat pump is used for house, office, hotel, and so forth, which

need heating or cooling separately, with each area needing to be controlled.

The unit can be installed on any place outdoor which can carry heavy machine such

as terrace, housetop, ground and so on.

The location must have good ventilation.

The place is free from heat radiation and other fire or flame.

A pall is needed in winter to protect the heat pump from snow.

There must be not obstacles near the air inlet and outlet of the heat pump.

A place which is free from strong air blowing.

There must be water channel around the heat pump to drain the condensing water .

There must be enough space around the unit for maintenance.

3 Installation place

Installation

10

5 Water loop connection

inspection during running.

Please pay attention to below matters when the water pipe is connected:

Try to reduce the resistance to the water from the piping.

The piping must be clear and free from dirty and blocks. Water leakage test must be

carried out to ensure there is no water leaking. And then the insulation can be made.

Attention that the pipe must be tested by pressure separately. DO NOT test it together

with the heat pump.

There must be expansion tank on the top point of the water loop, and the water level in

the tank must be at least 0.5 meter higher than the top point of the water loop.

The flow switch is installed inside of the heat pump, check to ensure that the wiring and

action of the switch is normal and controlled by the controller.

Try to avoid air staying inside of the water pipe, and there must be air vent on the top point of

the water loop.

There must be thermometer and pressure meter at the water inlet and outlet, for easy

6 Power supply connection

Open the front panel, and open the power supply access.

If the outside water pump is needed, please insert the power supply wire into the wire

access also and connect to the water pump terminals.

The power supply must go through the wire access and be connected to the power

supply terminals in the controlling box. Then connect the 3-signal wire plugs of the

wire controller and main controller.

If an additional auxiliary heater is need to be controlled by the heat pump controller,

the relay (or power) of the aux-heater must be connected to the relevant output of

the controller.

7 Location of the unit

A

B

Air inlet

Air outlet

C

D

Maintenance

space

Requirement：

A>500mm； B>1500mm；

C>1000mm；D>500mm。

ATTENTION

wall

Installation

Inlet water

Outlet water

Installation

Inspection before trial running

Check the indoor unit, and make sure that the pipe connection is right and the relevant

valves are open .

Check the heat pump unit including all of the screws and parts of the heat pump to see if

they are in good order. When power on, review the indicator on the controller to see if

there is any failure indication. The gas gauge can be connected to the check valve to

see the high pressure(or low pressure) of the system during trial running.

Check the water loop, to ensure that the water inside of the expansion tank is enough, the

water supply is good, the water loop is full of water and without any air. Also make sure

there is good insulation for the water pipe.

Check the electrical wiring. Make sure that the power voltage is normal, the screws are

fastened, the wiring is made in line with the diagram, and the earthing is connected.

Trial running

When the water pump runs for 1 minutes, the compressor will start. Hear whether there is

strange sound from the compressor. If abnormal sound occurs please stop the unit and

check the compressor. If the compressor runs well please look for the pressure meter

of the refrigerant.

9 Trial Running

Then check whether the power input and running current is in line with the manual. If not

please stop and check.

Review whether the outlet water temperature is stable.

The parameters of the controller are set by the factory, it is not allowed to change then

by user himself.

Adjust the valves on the water loop, to make sure that the hot(cool) water supply to each

door is good and meet the requirement of heating(or cooling).

8 Transit

When the unit need to be hung up during installation, a 8

meters cable is needed, and there must be soft material

between the cable and the unit to prevent damage to

the heat pump cabinet. (See picture 1)

WARNING

DO NOT touch the heat exchanger of the heat pump with fingers or other objects！

Picture 1

or

11

Start the heat pump by press " " key on the controller. Check whether the water

pump is running, if it runs normally there will be 0.2 MPa on the water pressure meter.

10

5 Water loop connection

Please pay attention to below matters when the water pipe is connected:

Try to reduce the resistance to the water from the piping.

The piping must be clear and free from dirty and blocks. Water leakage test must be

carried out to ensure there is no water leaking. And then the insulation can be made.

Attention that the pipe must be tested by pressure separately. DO NOT test it together

with the heat pump.

The flow switch is installed inside of the heat pump, check to ensure that the wiring and

action of the switch is normal and controlled by the controller.

Try to avoid air stayed inside of the water pipe, and there must be air vent on the top

point of the water loop.

There must be thermometer and pressure meter at the water inlet and outlet, for easy

inspection during running.

There must be expansion tank on the top point of the water loop, and the water level in

the tank must be at least 0.5 meter higher than the top point of the water loop.

6 Power supply connection

Open the front panel, and open the power supply access.

If the outside water pump is needed, please insert the power supply wire into the wire

access also and connect to the water pump terminals.

The power supply must go through the wire access and be connected to the power

supply terminals in the controlling box. Then connect the 3-signal wire plugs of the

wire controller and main controller.

If an additional auxiliary heater is need to be controlled by the heat pump controller,

the relay (or power) of the aux-heater must be connected to the relevant output of

the controller.

7 Location of the unit

A

B

Air inlet

Air outlet

C

D

Maintenance

space

Requirement：

A>500mm； B>1500mm；

C>1000mm；D>500mm。

ATTENTION

wall

Installation

Inlet water

Outlet water

Installation

Inspection before trial running

Check the indoor unit, and make sure that the pipe connection is right and the relevant

valves are open .

Check the heat pump unit including all of the screws and parts of the heat pump to see if

they are in good order. When power on, review the indicator on the controller to see if

there is any failure indication. The gas gauge can be connected to the check valve to

see the high pressure(or low pressure) of the system during trial running.

Check the water loop, to ensure that the water inside of the expansion tank is enough, the

water supply is good, the water loop is full of water and without any air. Also make sure

there is good insulation for the water pipe.

Check the electrical wiring. Make sure that the power voltage is normal, the screws are

fastened, the wiring is made in line with the diagram, and the earthing is connected.

Trial running

When the water pump runs for 1 minutes, the compressor will start. Hear whether there is

strange sound from the compressor. If abnormal sound occurs please stop the unit and

check the compressor. If the compressor runs well please look for the pressure meter

of the refrigerant.

9 Trial Running

Then check whether the power input and running current is in line with the manual. If not

please stop and check.

Review whether the outlet water temperature is stable.

The parameters of the controller are set by the factory, it is not allowed to change then

by user himself.

Adjust the valves on the water loop, to make sure that the hot(cool) water supply to each

door is good and meet the requirement of heating(or cooling).

8 Transit

When the unit need to be hung up during installation, a 8

meters cable is needed, and there must be soft material

between the cable and the unit to prevent damage to

the heat pump cabinet. (See picture 1)

WARNING

DO NOT touch the heat exchanger of the heat pump with fingers or other objects！

Picture 1

or

11

Start the heat pump by press " " key on the controller. Check whether the water

pump is running, if it runs normally there will be 0.2 MPa on the water pressure meter.

Usage

12

Usage

13

AIR COOLED WATER

CHILLER

HEAT PUMPCONTROL

Esc

Prg

Press“ ”

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

Esc

Prg

16/02/2011 15:38

Esc

Prg

STATUS:Cooling

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Mode

2.2MAIN MENU

⑴

MODE SELECT

Esc

Prg

MAIN MENU

PARAMETER

TIME

Press“ ”

Prg

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

COOL/HEAT COOL

AUX HEATING OFF

Esc

Prg

STATUS:Cooling

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

TIMP CURVE

Esc

Prg

COOL/HEAT HEAT

AUX HEATING OFF

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Cooling mode

1.Function of wire controller

Function 2: Save the settings when they are

finished.

Function 1: Return to the former interface.

In ON/OFFstate, press this key to enter into menu

interface.

Function 1: Enter next interface.

Function 2: Change parameter value. The number

stands for the value will be flashing if it is changeable.

ON/OFF

Press this key to turn on or turn off the unit

Menu

Enter

Escape

Up

Down

Key

Key name

Key function

Prg

Esc

Press this key to select the upward option or increase

the parameter value.

Press this key to select the downward option or

decrease the parameter value.

2.1 Turn ON/OFF the unit

When the unit is off, press the key“ ” , then the unit is turned on, and vice

versa.

2.Usage of wire controller

Press“ ”

Standby interface

Running interface

In ON/OFF state, you can find the MENU option by pressing the key “ . Press“ ”to go to

menu interface, then press“ ”for mode select interface. Now you can select the operation

mode for the unit by pressing “ ”. Press “ ”once to save your setting and twice for

returning back to the former interface.（If the unit system is cool-only or electrical-heat, COOL

or HEAT mode can't be changed.If the unit systemis without electrical-heat, the AUX HEATING

Prg”

Esc

Press“ ”

back to the

former

interface

Press“ ”

back to the

former

interface

Usage

12

Usage

13

AIR COOLED WATER

CHILLER

HEAT PUMPCONTROL

Esc

Prg

Press“ ”

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

Esc

Prg

16/02/2011 15:38

Esc

Prg

STATUS:Cooling

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Mode

2.2MAIN MENU

⑴

MODE SELECT

Esc

Prg

MAIN MENU

PARAMETER

TIME

Press“ ”

Prg

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

COOL/HEAT COOL

AUX HEATING OFF

Esc

Prg

STATUS:Cooling

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

TIMP CURVE

Esc

Prg

COOL/HEAT HEAT

AUX HEATING OFF

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Cooling mode

1.Function of wire controller

Function 2: Save the settings when they are

finished.

Function 1: Return to the former interface.

In ON/OFFstate, press this key to enter into menu

interface.

Function 1: Enter next interface.

Function 2: Change parameter value. The number

stands for the value will be flashing if it is changeable.

ON/OFF

Press this key to turn on or turn off the unit

Menu

Enter

Escape

Up

Down

Key

Key name

Key function

Prg

Esc

Press this key to select the upward option or increase

the parameter value.

Press this key to select the downward option or

decrease the parameter value.

2.1 Turn ON/OFF the unit

When the unit is off, press the key“ ” , then the unit is turned on, and vice

versa.

2.Usage of wire controller

Press“ ”

Standby interface

Running interface

In ON/OFF state, you can find the MENU option by pressing the key “ . Press“ ”to go to

menu interface, then press“ ”for mode select interface. Now you can select the operation

mode for the unit by pressing “ ”. Press “ ”once to save your setting and twice for

returning back to the former interface.（If the unit system is cool-only or electrical-heat, COOL

or HEAT mode can't be changed.If the unit systemis without electrical-heat, the AUX HEATING

Prg”

Esc

Press“ ”

back to the

former

interface

Press“ ”

back to the

former

interface

Usage

14

15

Usage

Esc

Prg

MAIN MENU

PARAMETER

TIME

Esc

Prg

Status:Heating

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

TIMP CURVE

Esc

Heating mode

Esc

Prg

STATUS:Heating

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

WATER IN 17℃

WATER OUT 25℃

PIPE 1 26℃

PIPE 2 26℃

AMBIENT PEMP 23℃

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

COOL TEMP 12℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Prg

COOL TEMP 12℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Press“ ”

or“ ”

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

COOL TEMP 15℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Esc

Prg

COOL TEMP 15℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Press“ ”

back to the

former

interface

State of unit

⑵

In ON/OFF state, you can find the MENU option by pressing the key “ ”. Press“ ”to go to

menu interface. Press“ ”for changing unit status. Press “ ”to check the unit state and

press “ ” to return back to the former interface.

Prg

Esc

Press“ ”

Press“ ”back to the

former interface

Press“ ”

back to the

former

interface

2.3 Parameter

In OFF state, you could enter into the option selection interface by pressing the key “ ”.

Press“ ”to find out the Parameter option, then press“ ”to go to parameter setting.

Choose the value you want to change by pressing the key “ ”and the number stands for

the value will be flashing. Modify the value by using the key“ ”(increase)or“ ”

(decrease). Press “ ”once to save your setting and twice for returning back to the former

interface.

Prg

Esc

Press“ ”

to save setting

Press“ ”

Flashing Flashing

Press“ ”

back to the

former

interface

Usage

14

15

Usage

Esc

Prg

MAIN MENU

PARAMETER

TIME

Esc

Prg

Status:Heating

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

TIMP CURVE

Esc

Heating mode

Esc

Prg

STATUS:Heating

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

WATER IN 17℃

WATER OUT 25℃

PIPE 1 26℃

PIPE 2 26℃

AMBIENT PEMP 23℃

Esc

Prg

MODE SELECT

UNIT STATUS

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

COOL TEMP 12℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Prg

COOL TEMP 12℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Press“ ”

or“ ”

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

COOL TEMP 15℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Esc

Prg

COOL TEMP 15℃

HEAT TEMP 40℃

DEF.CYC 45M

DEF.IN -7℃

DEF.OUT 13℃

DEF.TIME 8M

SYSTEM 4

SAVE YES

Press“ ”

back to the

former

interface

State of unit

⑵

In ON/OFF state, you can find the MENU option by pressing the key “ ”. Press“ ”to go to

menu interface. Press“ ”for changing unit status. Press “ ”to check the unit state and

press “ ” to return back to the former interface.

Prg

Esc

Press“ ”

Press“ ”back to the

former interface

Press“ ”

back to the

former

interface

2.3 Parameter

In OFF state, you could enter into the option selection interface by pressing the key “ ”.

Press“ ”to find out the Parameter option, then press“ ”to go to parameter setting.

Choose the value you want to change by pressing the key “ ”and the number stands for

the value will be flashing. Modify the value by using the key“ ”(increase)or“ ”

(decrease). Press “ ”once to save your setting and twice for returning back to the former

interface.

Prg

Esc

Press“ ”

to save setting

Press“ ”

Flashing Flashing

Press“ ”

back to the

former

interface

16

Usage

17

Usage

Esc

Prg

Status:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

DATE 24/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 24/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2012

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2012

CLOCK 16:02

TIMER ON 22:00

TIMER OFF 23:00

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Press“ ”

2.4 Time setting

In the ON/OFF state, press“ ” and you will see the Timer option. Press“ ”to choose the

Timer option, then press“ ”to enter into the time setting interface. Use“ ”（up）or“ ”（

down）to choose the value that you need to modify. Press“ ”and the target number is

flashing. Press“ ”（increase）or“ ”（decrease）for changing the value. Press“ ”to

save the setting. Press “ ”to return to former interface without any modification.

Prg

Esc

Press“ ”

Flashing

Press“ ”

or“ ”

Press“ ”

Flashing

Press“ ”

or“ ”

Press“ ”

Flashing Flashing

Press“ ”

or“ ”

Press“ ”

back to the

former

interface

Press“ ”back to

the former interface

Means that the unit shuts

down at 23:00 automatically.

Means that the unit turns

on at 22:00 automatically.

Note: When there is a “ ”shows in Time on and Time off option as shown above, it means

that the unit will not turn on or shut down automatically. When there is a clock icon shown as

blow, it means that the timer restart or shutdown is set.

The unit will

turns on or

shuts down

automatically.

16

Usage

17

Usage

Esc

Prg

Status:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

DATE 24/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 24/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/03/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2011

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2012

CLOCK 16:02

TIMER ON 08:00

TIMER OFF 22:30

Esc

Prg

DATE 25/04/2012

CLOCK 16:02

TIMER ON 22:00

TIMER OFF 23:00

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Press“ ”

2.4 Time setting

In the ON/OFF state, press“ ” and you will see the Timer option. Press“ ”to choose the

Timer option, then press“ ”to enter into the time setting interface. Use“ ”（up）or“ ”（

down）to choose the value that you need to modify. Press“ ”and the target number is

flashing. Press“ ”（increase）or“ ”（decrease）for changing the value. Press“ ”to

save the setting. Press “ ”to return to former interface without any modification.

Prg

Esc

Press“ ”

Flashing

Press“ ”

or“ ”

Press“ ”

Flashing

Press“ ”

or“ ”

Press“ ”

Flashing Flashing

Press“ ”

or“ ”

Press“ ”

back to the

former

interface

Press“ ”back to

the former interface

Means that the unit shuts

down at 23:00 automatically.

Means that the unit turns

on at 22:00 automatically.

Note: When there is a “ ”shows in Time on and Time off option as shown above, it means

that the unit will not turn on or shut down automatically. When there is a clock icon shown as

blow, it means that the timer restart or shutdown is set.

The unit will

turns on or

shuts down

automatically.

18

Usage

19

Usage

Prg

Esc

Prg

Esc

Prg

ALARM

WATER IN

2.5 TEMP CURVE

You can check temperature curves of water inlet, water outlet, coil 1, coil 2, coil 3 and coil 4.

At main interface, press “ ” to enter menu interface, then press “ ” to select TEMP

CURVE and “ ” to enter this interface. Choose parameters and press “ ” to check it. You

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Prg

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

OUT TEMP

IN TEMP

PIPE 1

PIPE 2

Prg

Esc

Prg

OUT TEMP 25.5℃

64

48

32

16

0

-16

3 0

Esc

Prg

OUT TEMP

IN TEMP

PIPE 1

PIPE 2

Esc

Prg

MAIN MENU

PARAMETER

TIME

TIMP CURVE

Esc

Prg

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Esc

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

STATUS:Standby

Inlet water temp. 20℃

Outlet water temp. 30℃

16/02/2011 15:38

Press“ ”

back to the

former

interface

Press“ ”back to the

former interface

Press“ ”

back to the

former

interface

Long press

“ ”

2.6 Keyboard locking

To avoid any faulty operations by others, please lock the keyboard after finishing settings.

In the ON/OFF state, press“ ”till the screen shows the keylock symbol as blow. Under

such condition, you cannot change any settings on the unit.In the locking state, press “ ”

till the keylock symbol dismissed and now you can make any modifications to the unit by

Keylock symbol

Note: When the keyboard is locked before power supply is cut, the keyboard will be unlocked

automatically as you reset the unit when it is power on.

2.7 Malfunction

If there is something wrong with the unit, the system will display malfunction code according to

the fault reasons.

Refer to malfunction table for any code meanings.

There is something wrong

with the temperature sensor

of inlet water .

Page is loading ...

Evo Control 13 Series Owner's manual

Evo Control 13 Series Owner's manual

Related papers

Other documents