APS Resource G-Flex DockLight Installation and Owner's Manual

Brand: APS Resource

Model: G-Flex DockLight

Type: Installation and Owner's Manual

G-FLEX

DOCKLIGHT

™

Installation and Owner's Manual

Do not install, operate or service this product

unless you have read and understand the

Safety Practices, Warnings, and Installation

and Operating Instructions contained in this

manual. Failure to do so could result in death

or serious injury.

AP6854 RD 07/14

6219 West Eastwood Court • Mequon, Wisconsin 53092 • TEL: (262) 518-1000 • www.apsresource.com

APS Resource

Your Aftermarket Solution

LIMITED WARRANTY

SAFETY SIGNAL WORDS

You may nd safety signal words such as DANGER, WARNING, CAUTION or NOTICE throughout the owner's

manual. Their use is explained below.

Indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Notice is used to address practices not related to

personal injury.

THIS LIMITED WARRANTY IS APS RESOURCE'S SOLE AND EXCLUSIVE WARRANTY WITH RESPECT

TO THE DOCKLIGHT AND IS IN LIEU OF ANY OTHER GUARANTEES OR WARRANTIES, EXPRESS OR

IMPLIED

APS Resource warrants that this G-FLEX DOCKLIGHT™ will be free from aws in material and workmanship

under normal use for a period of one (1) year from the earlier of 1) 60 days after the date of initial shipment by

APS Resource, or 2) the date of installation of the G-FLEX DOCKLIGHT™ by the original purchaser, provided

that the owner maintains and operates the G-FLEX DOCKLIGHT™ in accordance with this User’s Manual.

In the event that this G-FLEX DOCKLIGHT™ proves decient in material or workmanship within the applicable

Limited Warranty period, owner shall so notify APS Resource, and APS Resource will, at its option:

1. Replace the G-FLEX DOCKLIGHT™, or the decient portion(s) thereof, without charge to the owner; or

2. Alter or repair the G-FLEX DOCKLIGHT™, on site or elsewhere, without charge to the owner.

This Limited Warranty does not cover any failure caused by improper installation, abuse, improper operation,

negligence, or failure to maintain and adjust the G-FLEX DOCKLIGHT™ properly. Parts requiring replacement

due to damage resulting from vehicle impact, abuse, or improper operation are not covered by this warranty.

APS RESOURCE DISCLAIMS ANY RESPONSIBILITY OR LIABILITY FOR ANY LOSS OR DAMAGE OF

ANY KIND (INCLUDING WITHOUT LIMITATION, DIRECT, INDIRECT, CONSEQUENTIAL OR PUNITIVE

DAMAGES, OR LOST PROFITS OR LOST PRODUCTION) arising out of or related to the use, installation

or maintenance of the G-FLEX DOCKLIGHT™ (including premature product wear, product failure, property

damage or bodily injury resulting from use of unauthorized replacement parts or modication of the G-FLEX

DOCKLIGHT™). APS Resource’s sole obligation with regard to a G-FLEX DOCKLIGHT™ that is claimed to

be decient in material or workmanship shall be as set forth in this Limited Warranty. This Limited Warranty

will be null and void if the original purchaser does not notify APS Resource’s warranty department within

ninety (90) days after the product deciency is discovered.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION

ON THE FACE HEREOF, INCLUDING, BUT NOT LIMITED TO, A WARRANTY OF MERCHANTABILITY OR

OF FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH APS RESOURCE HEREBY DISCLAIMS.

APS RESOURCE

6219 W. EASTWOOD COURT

MEQUON, WI. 53092

SAFETY/INSTALLATION

SAFETY PRACTICES

Do not install, operate or service this product unless

you have read and followed the Safety Practices,

Warnings, Installation and Operating Instructions

contained in this manual. Failure to do so could

result in death or serious injury.

Place barricades around pit on dock floor and drive

while installing, maintaining or repairing.

Be certain to follow the installation instructions.

ELECTRICAL SHOCK POTENTIAL!! Do not attempt

to install, maintain or relamp without disconnecting

all power. Failure to disconnect power can result in

electrocution, shock or severe burns.

This fixture is designed for permanent installation in

ordinary (Non-Hazardous) locations in accordance

with the National Electrical Code and all applicable

local codes. Do not use in areas of limited ventilation

or in high ambient enclosures. The lamp and

fixture operate at high temperatures. Contact with

combustible materials can cause fire and personal

contact can cause severe burns.

This fixture must be plugged into an electrical supply

with a grounded receptacle.

Never use an incandescent type lamp over 150 Watts

or LED type lamp over 30 Watts. Using lamps of a

higher wattage than the fixture rating may cause

overheating and fire.

Risk of burns. Do not operate without wire guard.

Wire guards are UL required components. Replace

immediately if damaged or missing.

The installation and servicing of this product should

be performed by a qualified electrician or personnel.

Read and save these instructions. When using the

G-FLEX DOCKLIGHT™, basic safety precautions

should always be followed to reduce the risk of fire,

electrical shock and personal injury, including the fol-

lowing:

1. It is recommended that two hands are used for

positioning the neck and light head.

2. Unplug and allow to cool before replacing parts.

3. Use only with approved service parts.

4. IMPORTANT SAFETY INSTRUCTIONS: Dry

Location Use.

This docklight is rated 120V, 50/60 Hz. Check electrical

service running to the installation area to assure it

agrees with the correct voltage and electrical load for

the G-FLEX DOCKLIGHT™.

For best operation, APS Resource recommends that

the docklight be mounted such that the exible arm is

oriented upward.

INSTALLATION

1. Select a sturdy mounting location suitable to

support the weight of the xture.

• The docklight requires a 9" wide x 6" high at

surface for mounting the base of the light.

• The docklight base should be mounted at

a height that allows a dock worker to easily

position the light xture into the trailer being

serviced. For typical applications, the

docklight base will be approximately 4 feet

above the dock oor.

• The docklight base should be mounted as

close to the door opening as possible without

interfering with the operation of the door, or

any other equipment. A standoff bracket (P/N

AP6840) is included with the docklight, and

may be required for some applications.

FLEXIBLE

ARM

SERVICE/PARTS

INSTALLATION (cont.)

ITEM QTY DESCRIPTION P/N

1 3 SCREW, #8 X 3/8" LNG AP6852

2 1 LAMP SHADE AP6857

3 1 WIRE GUARD AP6858

4 1 LAMP SOCKET AP6859

5 1 SECURITY FASTENER AP6861

6 2 SCREW, #10-32 X 5/16" LNG AP6862

7 1 DECAL AP6864

8 1 TOOL, SECURITY FASTENER AP6863

9 N/A STANDOFF BRACKET

(NOT SHOWN)

AP6840

2. Remove the two fasteners located at the top of

the enclosure.

3. Slide the enclosure cover along the exible arm

to expose the backplate.

4. Use 1/4" fasteners or anchors to secure the

xture to the mounting surface.

The wire guard is secured to the plastic lamp shade

using a special security type fastener which helps

deter theft of lamps.

5. Locate the security fastener removal tool which is

attached to the backplate inside the enclosure.

6. Use the tool to remove the security fastener from

the lamp shade.

7. Rotate the wire guard to allow the wire guard to

pass through the small slot in the shade.

8. Install (or replace) the lamp.

9. Reinstall the wire guard and security fastener.

10. Return the security fastener tool to its proper

location.

11. Reinstall the enclosure cover and fasteners

located at the top of the enclosure.

12. Apply power to the docklight.

13. Use the ON/OFF switch located on the base of

the docklight to turn the docklight on and off.

SERVICE

The wire guard is secured to the plastic lamp shade

using a special security type fastener which helps

deter theft of lamps.

To replace the lamp, follow the instructions listed in

the INSTALLATION section of this manual.

To ensure proper function, durability and safety of the

product, only replacement parts that do not interfere

with the safe, normal operation of the product must be

used. Incorporation of replacement parts or modica-

tions that weaken the structural integrity of the prod-

uct, or in any way alter the product from its normal

working condition at the time of purchase from APS

Resource could result in product malfunction, break-

down, premature wear, death or serious injury.

PARTS

APS Resource G-Flex DockLight Installation and Owner's Manual

Brand: APS Resource

Model: G-Flex DockLight

Type: Installation and Owner's Manual

Download PDF

report

APS Resource G-Flex DockLight Installation and Owner's Manual

APS Resource G-Flex DockLight Installation and Owner's Manual

Related papers

Other documents