Haier HT-2180 User manual

Brand: Haier

Model: HT-2180

Category: LCD TVs

Type: User manual

This manual is also suitable for

HT-2180T

The Haier HT-2180 is a 21-inch color television with a variety of features to enhance your viewing experience. With the ability to store up to 218 programs, you can easily access your favorite channels. The fast teletext feature provides quick and convenient access to information, while the multi-picture modes allow you to view multiple channels simultaneously. The auto-correcting black balance ensures optimal picture quality, and the built-in sound system delivers rich and immersive audio.

MAIN FUNCTION

HT-2180

Colour Television

Operation Instructions

◆218 Programs stored

◆Fast teletext

◆Multi-picture modes

◆Auto-correcting black balance

CONTENTS

WARNING AND CAUTIONS

BASIC FEATURE

TECHNICAL SPECIFICATION

CONTROL LOCATION

INPUT AND OUTPUT TERMINALS

REMOTE CONTROLLER BOARD

OPERATING MENU

MULTI FUNCTION TIMER

GENERAL OPERATION

TELETEXT FUNCTION

TELEVISION INSTALLATION

CONNECTING OTHER EXTERNAL DEVICES

TROUBLE SHOOTING GUIDE

BASIC FEATURE

TECHNICAL SPECIFICATION

●218 programs stored

●Fast teletext

●Multi-picture modes

●Auto-correcting black balance

WARNING AND CAUTIONS

1. When you clean the TV set, please

pull out the power plug from AC outlet.

Or may result in electric shock, fire or

damage to the TV set. Don't clean the

cabinet and the screen with benzene,

petrol and other chemicals.

4. Do not place the TV set near rain or

moisture as it may cause an electric

shock, or the TV set to catch fire. The TV

set must only be used

in dry indoor location.

2. In order to prolong the using life of the

TV set, please place it in a well ventilated

location.

5. The back cover must only be removed

by a registered electrical service person.

Removing the back cover may result in

electric shock, fire or damage to

the TV set.

3. Don't place the TV

set in direct sunlight or

near heat source.

6. If the TV set is not going to be used for

long time, or there is a severe thunder &

lightening storm, it is recommended that

the TV set be disconnected from the AC

power outlet and the aerial plug

removed.

Explanation on the display tube

Should the picture tube require cleaning, disconnect the power and use a dry

soft cotton cloth. Do not use any cleaner or abrasive cloth.

1.POWER SUPPLY: See rating plate

2.COLOUR SYSTEM: PAL SECAM N TSC4.43/3.58(AV)

3.AUDIO SYSTEM: B/G D/K

4.CRT: 21”

5.ANTENNA INPUT : 75Ω Standard Coaxial Cable

6.SOUND OUTPUT POWER: 3W + 3W

7.POWER CONSUMPTION: See rating plate

8.NET WEIGHT(kg): 21.5

9.NET DIMENSION(mm): 610 x 460 x 490

Supplied accessories:

Infrared remote control handset 1

Battery(AA) 2

Operating instruction 1

Design and specifications are subject to change without notice.

CONTROL LOCATION

2.Rear Panel

INPUT AND OUTPUT TERMINALS

It can be connected to the following appliances:

video-tape recorder, video camera, tape recorder

and audio amplifier, etc......

*Please keep AC cord unplugged when connecting

TV system.

1.Front Panel

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)

ME NU

TV /A V

PR O

(1)Power switch: press the button to turn on the TV set ,press the button again to

turn off the TV set.

(2)Program up/down button

(3)Volume up/down button

(4)TV/AV switch button

(5)Menu button

(6)Power indicator: the indicator lights in standby status .The indicator glints

when you use remote controller.

(7)Remote sensor: let the remote controller aim here, the TV set can receive remote

control signal.

(8)Audio(R) input

(9)Audio(L) input

(10)Video input

OPERATION MENU

1.Entering and exiting menus

Press MENU button on the remote controller once (or directly

press PICTURE button on the remote controller),PICTURE

menu display on the screen; press MENU button

twice (or directly press SOUND button on the remote

controller), SOUND menu display on the screen .

Press the menu button again (3 times, or directly press

TIME button on the remote controller), TIME menu display

on the screen. Press the menu button again (4 times, or directly press FUNCTION button on the

remote controller),FUNCTION menu display on the screen. Press the menu button again (5

times or directly press TUNE button on the remote controller), TUNE menu display on the

screen .Press the menu button again (6 times),EXCHANGE menu display on the screen .To

turn off the on screen menu display, either press the EXIT button or allow the TV set to

automatically turn off the menu by not pressing any buttons for a few seconds.

2.Auto search

A. Press MENU button five times (or directly press TUNE button on the remote controller),

Press MENU button five times (or directly press TUNE button), ensure that the

TUNE menu is displayed. Press the CH+/-buttons to select SEARCH. Then press the VOL+

button to search up or V-button to search down to the next TV station.(It is much faster to

search up.)If the wrong station is found ,press the search item again. You may need to

repeat this until the correct station is located. To store the new program, press the EXIT

button.

4.Fine tune

If the picture or sound is poor, try to use the FINE TUNE feature. Select the FINE TUNE by

using the CH +/- buttons. Use the VOL +/- buttons to fine-tune the sound and picture for

optimum results. Then press the EXIT button to store the results. Do not use this feature unless

reception is poor.

nsure that the TUNE menu is displayed. Press the CH+/- buttons to select AUTO SEARCH.

Then press the VOL+button,the TV set will begin to search programs from present programme

No..

B. After the search has finished, the TV set will return to the first program stored.

3. Search

5.Selecting the sound system

Press the CH+/- buttons to select SOUND item. Then press the VOL+/- button to select a sound

system you need.

TUNE

COLOUR AUTO

SOUND BG

BAND VHFL

SKIP OFF

PROGRAM 19

FINE TUNE

AUTO SEARCH

6.Selecting colour system

Usually this should be set in the auto position. However if the colours displayed on the

screen are incorrect you can manually select the correct colour system. When you have

finished, remember to turn it back to auto again so that other programs will still work

correctly. Use the CH+/- buttons to select COLOUR then press the VOL+/- buttons to

select a colour system you need. Press the EXIT button to save the setting.

Setting channels

MARK

FUNCTION DESCRIPTION

MUTE

STANDBY

ONE DIGIT SELECTION

ONE OR TWO OR THREE DIGITS PRE-SELECTION

TV/VIDEO SELECTION

MENU DISPLAY

VOLUME CONTROL

CHANNEL NUMBER UP/DOWN

0-9

-/--

TV/AV

SWAP

-VOL+

-CH+

PICTURE MENU

PICTURE

SOUND MENU

SOUND

TIME MENU

TIME

FUNCTION MENU

FUNCTION

.SD

W P

I R

V +

C H

TI N

U TI

E U

F TU

-/-

OOM

CLAL

- I

S A

PROGRAM SCAN

AL D

I-

TELETEXT SUBTITLE

INVALID BUTTON

PICTURE MODE SELECTION

INVALID BUTTON

TUNE MENU SELECTION

TV/TELETEXT ENTERING/EXITING

TO REVEAL CONCEALED TELETEXT

TELETEXT ZOOM

TELETEXT PAGE HOLD

TELETEXT/TV MIX MODE

TV/TELETEXT ALTERATION

TIME DISPLAY(IN TV MODE)/SUBCODE SWITCH

EAST/WEST

EXIT MENU DISPLAY

REMOTE CONTROLLER BOARD

NOTE：

Use CH+/- or VOL+/ -buttons, either on the remote controller or on the front panel

of the television to navigate menus and to select menu options.

RECALL PREVIOUS PROGRAM

OPERATION MENU

Press the MENU button once or press the PICTURE

button on the remote control to display the Picture

setting menu.

1.Contrast (adds depth to the picture)

Press the CH+/- buttons to select CONTRAST, then

press the VOL+/- buttons to adjust the contrast level.

2.Brightness (adds sparkle and shine to the picture)

Press the CH+/- buttons to select BRIGHTNESS, then press the VOL+/- buttons

to adjust the brightness level.

3.Colour (adds colour depth)

Press the CH+/- buttons to select COLOUR, then press the VOL+/- buttons to

adjust the colour level.

4.Sharpness (adds fine detail)

Press the CH+/- buttons to select SHARPNESS, then press the VOL+/- buttons to

adjust the sharpness level.

Note: Do not turn the sharpness up to high if the reception is poor or has lots of

noise as it will enhance the fine grain details.

5.Black stretch (adds deeper blacks and increases the contrast range)

Press the CH+/- buttons to select BLACK STRETCH, then press the VOL+/- buttons

to turn this feature on/off.

6.Hue

Press the CH+/- buttons to select HUE, then press the VOL+/-buttons to adjust

the hue level.

Note: Hue is only used in the AV mode.

7.Program skip

The Program skip feature enables you to skip/hide programs that you do not

wish to be displayed when using the CH+/- buttons. These channels will still

be displayed by directly using the channel number buttons on the remote

controller. To skip , press the CH+/- buttons to select the SKIP item, press the

VOL+/- buttons to tune the skip feature on/off. Press the EXIT button to save

the setting.

8.Program number

The program number is the remote control channel number. You can change the

program number to see channels stored without exiting this main menu. Press the

CH+/- buttons to select PROGRAM, press the VOL+/- buttons to change the program

number that you are adjusting.

9.Band switching (Note: This is a new item.)

If you already know what band the channel is on, tuning can speed up by

selecting the correct band before going into the search menu. This feature

should only be used if you understand the channels in your local area.

Picture Adjustments

PICTURE

CONTRAST 89

BRIGHTNESS 66

COLOUR 50

SHARPNESS 50

BLACK STRETCH OFF

IIIIIIIIIIIIIIIIIIIIIIIII..........

OPERATION MENU

Sound Adjustments

Press the menu button twice or press the SOUND button on the remote controller

to display the sound setting menu.

Volume (adjust the loudness level)

Press the CH+/- buttons to select VOLUME,

then press the VOL+/- buttons to adjust the

volume level.

SOUND

VOLUME 50

IIIIIIIIIIIIIIIIIIIIIIIII..........

FUNCTION

ENGLISH

BACKGROUND ON

NOISE REDUCE OFF

FADE ON

CHILD LOCK OFF

AVL OFF

CALENDER

1.Background (If the signal is very poor or there is no

input signal the picture will mute to black.)

Press the CH+/- buttons to select BACKGROUND,

then press the VOL+/- buttons to turn this feature

on/off.

2.Noise reduce (Picture Noise & Grain reduction circuit)

Press the CH+/- buttons to select NOISE REDUCE, then

press the VOL+/- buttons to turn this feature on/off.

4.Child lock (enables the TV front control buttons to be locked)

Press the CH+/- buttons to select CHILD LOCK, then press the VOL+/-

buttons to turn this feature on/off.

5.AVL (Automatic Volume Limit control reduces effect of large volume

changes such as when the ads come on.)

Press the CH+/- buttons to select AVL, then press the VOL+/- buttons to turn

this feature on/off.

6.Calendar (enables the TV sets internal calendar to be set)

Press the CH+/- buttons to select CALENDAR, then press the VOL+/-

buttons to select the item to be changed and the CH+/- buttons to alter

each setting.

3.Fade

The FADE control allows time for the picture tube to warm up and gently

turned on, which can help prolong the life of the picture tube.

Function Menu

TIME

CLOCK --:--

ON TIME --:--

ON-PROG 1

OFF TIME --:--

SLEEP TIMER --:--

REMIND TIME --:--

REMIND PROG 1

MULTI FUNCTION TIMER

Multi Function Timer

The TV set has in built a comprehensive timer

that has five basic functions.

1.Clock

2.On time so that the TV set can be programmed

to turn on at a certain time.

3.Off time to allow the TV set to turn off at a

preset time.

4.Sleep timer to allow the TV set to turn off after

10 ~ 180 minutes.

5.Program remind timer, that displays an on-

screen reminder prompt, when a program on a

different channel is due to start.

Selecting the clock menu

Press the MENU button continually until theTIME menu is displayed or press

the yellow time button on the remote controller.

1.Clock (master timer clock)

Press the CH+/- buttons to select CLOCK, then press the VOL+/- buttons to

adjust the hour. Press The CH- buttons to select minute and the VOL +/- buttons to

adjust the minute.

2.On Time

Press the CH+/- buttons to select ON TIME, then press the VOL+/- buttons to

adjust the hour .Press the CH- button to select minutes and the VOL+/- buttons to

adjust the minutes. Press the CH- button to select ON-PROG and the VOL+/- buttons

to select the TV channel that the TV set will automatically turn on to.

3.Off Time

Press the CH+/- buttons to select OFF TIME, then press the VOL+/- buttons to

adjust the hour. Press the CH- button to select minute and the VOL+/- buttons to

adjust the minute.

4. Sleep Timer

Press the CH+/- buttons to select SLEEP TIMER, then press the VOL+ button

Note: The clock will only work in the TV set if left turned on or in standby.

When the set is disconnect from the power supply or is turned off by the

main power switch on the front panel, the clock looses power and will

need to be reset when the power is reconnected.

EXCHANGE

PROGRAM 1 1

PROGRAM 2 1

EXCHANGE

MULTI FUNCTION TIMER

to adjust the amount of time before the TV set will automatically turn off. Each time

the VOL+ button is pressed the sleep time will increase by 10 minutes. The

maximum sleep time is 180 minutes.

5. Remind Time

Press the CH+/- buttons to select REMIND TIME, then press the VOL+/- buttons to

adjust the hour. Press the CH- button to select minute and the VOL +/- buttons to

adjust the minute. Press the CH- button to select REMIND PROG and the VOL +/-

buttons to select the TV channel that the TV set will automatically remind you to

turn to while watching another channel.

Program Number Exchange

This feature enables TV programs that

may be on a wrong TV channel number

to be swapped/exchanged. This feature

is very useful when Automatic Search

Tuning has been used, to reallocate the

found programs to the correct channel

numbers.

Press the MENU button 6 times until the

exchange menu is displayed.

Press the CH+/- buttons until program 1 is

selected. Use the VOL+/- buttons to

select the channel number to be swapped.

(I.E If you wish to exchange channel 2

and 4 PROGRAM 1 should = 2.)

Press the CH+/- buttons until program 2 is

selected. Use the VOL+/- buttons to

select the channel number to be swapped.

(I.E If you wish to exchange channel 2

And 4 PROGRAM 2 should = 4.)

Press the CH+/- buttons until EXCHANGE is

selected. Press the VOL+ button to

enable the exchange.

GENERAL OPERATION

6.Recall (on-screen display)

The CALL button on the remote controller allows the on screen menu to be

displayed, showing the channel numbers and colour system and sound system.

7.Program Scan (Automatically increments/scans the channels and displays

each channel for a short time.)

The SCAN button on the remote controller turns on/off the scan feature.

8.Channel Swap (toggles between the last channel view and the current

channel)

Each time the SWAP button is pressed, the last channel view is displayed.

9.AV input selection

Each time the TV/AV button is pressed, the input selection will cycle among

TV- AV1- AV2-SVHS(Y/C)- RGB- TV.

Notes: I.SVHS is used as Y/C input in scart-cable.

Ⅱ.AV1 is used as VIDEO input in scart-cable.

III.AV2 is used as side AV input in scart-cable.

1.Channel changing (218 possible channels)

Use either the CH+/- buttons on the remote controller or the front panel of the TV set

to change the channels. Or directly enter the channel number with the numeric button

on the remote controller.

2.Volume adjustment

Press the VOL+/- buttons on the remote controller or the front of the TV set to adjust

the volume level. The range is 0~100. When the volume buttons are pressed, the

volume level is displayed automatically on the TV screen.

3.Standby

Using the remote controller the TV set can be placed into standby mode.

A red standby light will glow on the TV front panel when the TV

set is placed into standby. To turn the TV set back on again, press standby button

on the remote controller again. It will take a few seconds before a picture is

displayed.

4.Mute

Press the MUTE button on the remote controller to mute the TV set’s sound. Pressing

the MUTE button again will turn the sound back on.

5.Preset picture modes

Our engineers have designed in 5 commonly used picture settings to allow fast

picture level selection depending on what type of TV program is showing. Each

mode is selected in turn by pressing the "P. STD" button on the remote controller.

The 5 modes are:

Listen- This is a new feature that blacks out the TV screen when listening to

music only channels.

Soft - Designed for night time low light viewing.

Standard - Designed for rooms that have good all round lighting.

Rich - Designed for rooms with high ambient lighting such as daytime sport.

User- A spare setting that can be adjusted to personal tastes.

All the 5 modes can be independently adjusted by using the PICTURE

adjustment menu.

Press repeatedly the [-/--] button to select the appropriate number of digits for

the next program number that you want to watch. The on screen indication will

change sequentially between one digit (-) for 0 to 9, two digits (- -) for 10 to

99 and 3 digits (- - -) for 100 to 218 input selection. After selecting the number

of digits, simply press the numeric keys for the desired program number. For

example, to select program 34, press the button [- / - -] until the on screen

indication shows (- -), then press 3 and finally 4.

Standby

mode must be used when the timer has been set to turn on the television

automatically.

1.TV/Teletext Button (Turns the Teletext feature On/Off) [ ]

Press the [ ] button on the remote control to turn teletext On/Off.

To select a teletext page either directly enter the page number using the numeric key

pad on the remote control or use the CH+/- buttons, or the coloured Fast Text buttons.

2.Mix Mode [ ]

While in Teletext mode press the [ ] and will show the teletext data superimposed on

top of the TV picture. Press the button again to revert back to Full text.

3.Cancel Mode [ ]

This feature allows the TV picture to be displayed while next page to be searched is

entered and found. Only the top teletext line is displayed until the page is found.

Press the [ ] button to hide the teletext information. Either press the [ ]

(Cancel button) or the [ ] (Text button) to exit the cancel display mode.

4.Language Mode [ ]

Pressing the [ ] button will change the Teletext characters between Eastern and

Western.

5.Hold [ ]

Pressing the [ ] button will stop the teletext page automatically updating.

This feature is very useful where there are several teletext pages on the same

page number.

6.Size [ ]

Pressing the [ ] button changes between full screen top half bottom and

half full screen. This feature is very useful as it magnifies the image making

the characters easier to read.

7.Reveal [ ]

Pressing the [ ] button will reveal hidden text. This feature is used to

reveal information such as answers to teletext on-line interactive puzzles.

TELETEXT FUNCTION (FAST TEXT)

8.Subtitle [ ]

Pressing the [ ] button will get the teletext decoder to automatically

search for the subtitle page.

9.Time [ ]

While in normal TV mode only, pressing the [ ] button will display the

teletext time in the top right hand corner for a few seconds. In teletext mode,

the button can be used as subcode switch.

10.Fast text coloured buttons

Fast text automatically displays the four most commonly used pages that the

broadcaster thinks that you may want to choose next. Press the same coloured

button on the remote as the coloured link at the bottom of the teletext page to

go directly to that page.

TELETEXT FUNCTION (FAST TEXT)

TELEVISION INSTALLATION

Connect antenna or video facility

1. Use 75 coaxial cable plug or 300-75 impedance converter to plug in antenna

input terminal on the rear of the cabinet.

2. Connect the video facility to the radio, video in jack on the rear of the cabinet.

Install and replace batteries of the remote control unit:

1.Place the remote control unit with the face down, then open the battery cover of

the unit.

2.Place the two"AA"size batteries, match the + and - signs on each battery to the +

and -signs of the battery compartment.

3.Close the cover of the battery compartment.

NOTE:

(1)Don't drop or wet or dismantle the unit.

(2)If you don't intend to use the unit for a long period or the electricity of the

batteries is used up, remove the batteries to prevent batteries acid from leaking

into the battery compartment.

(3)Replace the two old batteries at the same time.

(4)Don't use charge battery (Ni-cd )and don't mix battery type.

(5)Don't throw your batteries into a fire. Dispose of your batteries in a required

place.



VHF antenna

UHF antenna

Mixer

75 Co-axis cable

Input terminal of antenna

Co-axis antenna plug

Antenna in jack

75 Co-axis antenna plug



CONNECTING OTHER EXTERNAL DEVICES

To connect signal from the player,

scart-cable would be connected

correspondingly. The device may

be to provide RGB or VIDEO or

Y/C output, you can use TV/AV

button to switch to the EURO, AV

signal you need.

VCR or DVD player or other

device for playing

Note:1.If the problem can not be fixed after you check above items. DO NOT attempt

to remove the back cover by yourself.

2.If the snapping sound from the cabinet of the TV set can be heard occasionally

because of temperature changing of environment, it is normal, you can use it

reassuringly.

TROUBLE SHOOTING GUIDE

BREAKDOWN PHENOMENON

The following problems are not always caused by hardware failure, please use

the follow trouble shooting guide before you call for service:

PICTURE

SOUND

CHECKING

The direction and connection of the

antenna

Direction, station and connection

of the antenna

Interference from electric

appliance. Automobile、Motor,

Vehicle Fluorescence lamp etc.

Volume, Sound mute

The power plug isn't plugged in AC

outlet. The main power isn't turned

on. The setting up of contrast, brig-

htness and volume.

Adjust color control

Adjust channel again

Moving the TV set or using magnetic electric appli-

ance near TV, Which will lead to color spot on sc-

reen. Please remove the electric appliance and cut

off power. After 120 minutes turn the TV on, the pic-

ture will be recovered.

Picture with Snow

Color Spot

No Color

No Picture

Normal

Disturb

Double or Triple Image

Noise

Normal

Noise

No Sound

Normal Volume

Normal or Weak Volume

Normal Volume

Scramble

Haier HT-2180 User manual

Brand: Haier

Model: HT-2180

Category: LCD TVs

Type: User manual

This manual is also suitable for

HT-2180T

Download PDF

report

Haier HT-2180 User manual

This manual is also suitable for

Haier HT-2180 User manual

Related papers

Other documents