H3C SecPath PSR300-12A2 &
PSR300-12D2 Power Modules
User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W102-20200303
Copyright © 2017-2020, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this
document are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.
Preface
Audience
This documentation is intended for:
• Network planners.
• Field technical support and servicing engineers.
• Network administrators working with the the H3C SecPath PSR300-12A2 & PSR300-12D2.
Documentation feedback
You can e-mail your comments about product documentation to [email protected].
We appreciate your comments.
i
Contents
Overview ························································································ 1
Views ······································································································································ 1
Technical specifications ··············································································································· 2
LEDs ······································································································································· 2
Installing and removing the power supply ·············································· 3
Safety precautions ····················································································································· 3
Tools ······································································································································· 3
Installing and removing the power supply ························································································ 3
Installing the power supply ···································································································· 3
Connecting the power cord ···································································································· 4
Removing the power supply ··································································································· 5
1
Overview
The PSR300-12A2 is an AC-input and DC-output power supply. The PSR300-12D2 is a DC-input
and DC-output power supply. They provide a maximum output power of 300 W.
The PSR300-12A2 and PSR300-12D2 power supplies have the following features:
• Provide protection against input overcurrent, input undervoltage, output overvoltage, output
short-circuit, and overtemperature.
• Support for 1+1 redundancy and load sharing.
• Hot swappable. You can hot swap a power supply when another power supply is operating.
Views
Figure 1 PSR300-12A2
(1) Power switch ("O" represents off and "—" represents on)
(2) Power receptacle (3) Air vent
(4) Handle (5) Power output status LED
(6) Power input status LED (7) Securing holes for the power cord retaining clasp
(8) Fastening screw
Figure 2 PSR300-12D2
(1) Power switch ("O" represents off and "—" represents on)
(2) Power receptacle (3) Air vent
(4) Handle (5) Power output status LED
(6) Power input status LED (7) Screw holes for securing the power cord connector
(8) Fastening screw
2
Technical specifications
Table 1 Technical specifications
Item Specifications
Rated input voltage
• PSR300-12A2: 100 VAC to 240 VAC
• PSR300-12D2: –48 VDC to –60 VDC
Output voltage 12 V
Maximum output current 25 A
Maximum output power 300 W
Dimensions (H × W × D) 40.13 × 101.6 × 234.9 mm (1.58 × 4.00 × 9.25 in)
Operating temperature 0°C to 55°C (32°F to 131°F)
Operating humidity 5% RH to 95% RH, noncondensing
LEDs
The power supply uses power input and power output LEDs to indicate the power input and output
status, respectively.
Table 2 LED description
LED Status Description
Power input status LED (AC OK or Input)
Off
No power is being input or an input failure has
occurred.
On Normal power input.
Power output status LED (DC OK or
Output)
Off
No power is being output or an output failure has
occurred.
On Normal power output.
If the power input LED is on but the output LED is off, an output issue or an overtemperature
condition might have occurred. To resolve the issue:
1. Turn off the power switch and disconnect the power cord. Then reconnect the power cord and
turn on the power switch.
This operation resolves the power supply failure caused by an output overvoltage, output
short-circuit, or output overcurrent condition. The power supply shuts down and latches off if
one of these conditions occurs and cannot automatically restore operation.
2. If the issue persists, the temperature might be high. Take measures to decrease the
temperature to an acceptable range. The power supply will automatically restore operation.
3
Installing and removing the power supply
Safety precautions
To avoid possible bodily injury and power supply and device damage, follow these safety
precautions:
• When installing and removing the power supply, always wear an ESD wrist strap and make sure
it makes good skin contact.
• Make sure the voltage of the power source is as required by the power supply, and the output
voltage of the power supply is as required by the device.
• To avoid bodily injury, do not touch any bare wire or terminal.
• Do not place the power supply in a wet location, and prevent liquid from flowing into the power
supply.
• To avoid power supply damage, do not open the power supply. If the internal wires or units are
faulty, contact H3C Support.
Tools
When installing and removing a power supply and power cord, you must wear an ESD wrist strap.
Prepare it yourself.
Installing and removing the power supply
The installation and removal procedures are similar for the PSR300-12A2 and PSR300-12D2 power
supplies. The following procedures install and remove a PSR300-12D2 power supply.
Installing the power supply
CAUTION:
To avoid bodily injury and device damage, strictly follow the procedure in Figure 3 to install the
power supply
.
Figure 3 Power supply installation procedure
Install the power supply
Connect the power cord
Turn on the circuit breaker
Start
End
4
To install the power supply:
1. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably
grounded.
2. Unpack the power supply and make sure the power supply model is as required.
Keep the power supply package secure for future use.
3. As shown in Figure 4, correctly orient th
e power supply (with the lettering on it upwards).
Grasping the module handle with one hand and supporting the module bottom with the other,
push the module slowly into the slot along the guide rails. Make sure the power supply has good
contact with the backplane connectors.
The power supply and power supply slot are designed to prevent disorientation and
misalignment. If you cannot insert the power supply smoothly into the slot, the orientation might
be wrong or the power supply is not aligned correctly with the slot. Pull out the power supply,
reorient the power supply or realign it with the slot, and insert it again.
4. When the power supply is fully seated in the slot, fasten the screw on the power supply.
Figure 4 Installing the power supply
Connecting the power cord
Connecting the AC power cord
WARNING!
• Make sure each power cord has a separate circuit breaker.
• Before connecting a power cord, turn off the circuit breaker for it.
To connect the AC power cord:
1. As shown in Figure 5, pivo
t up the power cord retaining clip, insert the female connector of the
AC power cord into the AC-input power receptacle on the power supply, and then pivot down
the power cord retaining clip.
5
Figure 5 Connecting the AC power cord to the power supply
2. Connect the other end of the AC power cord into an AC power source, and turn on the circuit
breaker for the power cord.
3. Turn on the power switch. If the AC OK LED is on, the power cord is connected correctly. If the
AC OK LED is off, the connection might be wrong. Verify the installation and resolve the issue.
Connecting the DC power cord
1. As shown in Figure 6, insert the connector of the DC power cord into the DC-input receptacle on
the power supply. Then fasten the screws on the connector.
The connector of the DC power cord and the DC-input receptacle are designed to prevent
disorientation. If you cannot insert the connector smoothly into the receptacle, the orientation
might be wrong. Remove the connector, reorient it, and connect it again.
2. Use a releasable cable tie to secure the power cord to the handle of the power supply.
Figure 6 Connecting the DC power cord
3. Connect the other end of the DC power cord to a DC power source.
4. Turn on the power switch on the power supply. If the Input LED is on, the power cord is
connected correctly. If the Input LED is off, the connection might be wrong. Verify the
installation and resolve the issue.
Removing the power supply
CAUTION:
To avoid bodily injury and device damage, strictly follow the procedure in Figure 7 to remove the
power supply
.
1
2
3
6
Figure 7 Power supply removal procedure
To remove the power supply:
1. Turn off the circuit breaker for the power cord.
2. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably
grounded.
3. Turn off the power switch.
4. Loosen the releasable cable tie that secures the power cord to the handle of the power supply.
5. Loosen the screws on the power cord connector and then remove the power cord.
Figure 8 Removing a DC power cord connector
(1) Loosen the screws on the power cord connector
(2) Pull the connector out
6. As shown in Figure 9, loosen the screw on the power supply. Grasping the power supply handle
with one hand, pull the power supply part way out of the slot. Supporting the power supply
bottom with the other, pull the power supply slowly out of the slot along the guide rails.
2
1
3
7
Figure 9 Removing the power supply
7. Put the removed power supply on an antistatic mat or into its package.
8. If you are not to install a new power supply, install the filler panel in the slot to prevent dust from
entering the chassis.
1 2
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
H3C SecPath PSR300-12A2 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
H3C SecPath PSR300-12D2 User manual
-
H3C s5820x series Installation guide
-
-
-
-
-
-
-
-