Noble House 15140 Operating instructions

No Picture Parts Qty No Picture Parts Qty

Assembly Instructions

List parts of Club Chair

A Chair Back 1 G Bolt Dia.M6*35mm(L) 4

B Left Arm 1 H Bolt Dia.M6*40mm(L) 8

C Right Arm 1 I

Flat washer

Ø16*1.2mm(TH)

12

D Chair Seat 1 J

Spring washer

Ø16*2mm(TH)

12

E Leveler 4 K Allen key 1

F

Plastic cap (to cover

bolt heads

)

12

Assembly Instructions:

Assembly

Instructions:

Step 1 and 2 : Open the carton and place all the parts onto a clean and soft

surface,compare the real parts with the above list to make sure each part is

available,place the left arm (B) with its inside facing up onto the soft surface,put the

chair back(A)against the left arm(B) with the chair back(A)

'

s upper metal rod inserted

Step 3 and 4 : Place the chair seat (D)with its short side facing front between the

left arm(B) and chair back(A),attach the chair seat(D)to the left arm(B) on their

sides with flat washer(I)+spring washer(J)+bolt(G), attach the chair seat(D) to the

chair back(A) on the rear side with flat washer(I)+spring washer(J)+bolt(H) use an

chair

back(A)against

the

left

arm(B)

with

the

chair

back(A)s

upper

metal

rod

inserted

into the top rear end of left arm(B), attach them together with flat washer(I)+spring

washer(J)+bolt(H),use an Allen key(K) to tighten them, but not completely.

chair

back(A)

on

the

rear

side

with

flat

washer(I)+spring

washer(J)+bolt(H)

,

use

an

Allen key(K) to tighten them ,but not completely

Step 5,6 and 7 : Place the right arm (C ) againt the chair back(A) and chair seat(D),

insert the chair back(A)

'

s upper metal rod into the top rear end of right arm( C ) attach

Step 8 and 9 : Turn the leveler(E)into the chair body,tighten all bolts completely and

put the plastic cap(F)to cover the bolt heads adjust the leveler(E)to ensure good

insert

the

chair

back(A)s

upper

metal

rod

into

the

top

rear

end

of

right

arm(

C

)

,

attach

the chair seat(D ) to the right arm(C ) with flat washer(I)+spring

washer(J)+bolt(G),attach the chair back (A) to the righ arm( C ) with flat washer((I) +

spring washer(J)+bolt(H), use an Allen key(K) to tighten them ,but not completely

put

the

plastic

cap(F)to

cover

the

bolt

heads

,

adjust

the

leveler(E)to

ensure

good

stability, it is ready for use.

Label Picture Description QTY

A Backrest with Leg 1

B Left Panel with Leg 1

C Right Panel with Leg 1

Caution : You must read this before you proceed

Armless Chair

Noble House Home Furnishings LLC

Page 1 OF 6

D Seat 1

E Back Cushion 1

F Seat Cushion 1

Label Picture Description QTY

①

Bolt Cap 11

②

Bolt (M6*45mm) 11

③

Washer 11

④

Spring Washer

(Ø16*2mm)

11

⑤

Allen Key 1

Before Beginning

Assembly:

Noble House Home Furnishings LLC

Page 2 OF 6

Step 1

Open the carton and place all part on a clean and soft surface.

Place the Backrest with Leg(A) against the Right Panel with Leg(C) as shown above.

Attach the Backrest with Leg(A) to Right Panel with Leg(C) using the Bolts(②), Spring Washers(④)

and Washers(③) with Alley Key(⑤).

Do not fully tighten the bolts.

Over View

This Armless Chair has multiple parts and may require up to 30 minutes to assemble. To give you an

overview of the Armless Chair parts, the above picture is to help you put the various parts into

perspective. Please read through the instructions below to familiarise yourself with the parts and steps

before assembly.

Backrest with Leg(A)

Left Panel with Leg (B)

Right Panel with Leg(C)

Seat(D)

Seat Cushion(F)

Back Cushion(E)

Noble House Home Furnishings LLC

Page 3 OF 6

Place the Left Panel with Leg(B) facedown on the clean and soft suface.

With the help of your adult partner, place the Backrest with Leg(A) against Left Panel with Leg(B).

Attach the Left Panel with Leg(B) to Seat(D) and Backrest with Leg(A) using Bolts(②), Spring

Washers(④) and Washers(③) with Alley Key(⑤).

Tighten all Bolts at all joints completely at this stage.

Attach the Seat(D) to Right Panel with Leg(C) using Bolts(②), Spring Washers(④) and Washers(③)

with Allen Key(⑤).

Do not fully tighten the bolts.

Step 3

Step 2

Noble House Home Furnishings LLC

Page 4 OF 6

Place the Seat Cushion(F) and Back Cushion(E) on the Armless Chair.

Your Armless Chair is ready for use.

This Armless Chair can only be used on a flat, level surface.

Step 4

Turn the Armless Chair face down on the clean, non-marring surface.

Use the Bolt Cap(①) to cover all Bolts.

Step 5

Place the Armless Chair on a level surface to check the wobbles.

If the Armless Chair wobbles, adjust the Levelers on the bottom of the Legs to make it level.

Step 6

Noble House Home Furnishings LLC

Page 5 OF 6

Noble House Home Furnishings LLC

Page 6 OF 6

Label Picture Description QTY

G Backrest with Leg 1

H Left Armrest with Leg 1

Caution : You must read this before you proceed

Left Armchair

Noble House Home Furnishings LLC

Page 1 OF 7

I Right Panel with Leg 1

J Seat 1

E Back Cushion 1

F Seat Cushion 1

Label Picture Description QTY

① Bolt Cap 11

②

Bolt (M6*45mm) 11

③

Washer 11

④

Spring Washer

(Ø16*2mm)

11

⑤

Allen Key 1

Noble House Home Furnishings LLC

Page 2 OF 7

Overview

This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview

of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read

through the instructions below to familiarise yourself with the parts and steps before assembly.

Before Beginning

Assembly:

Left Armrest with Leg(H)

Backrest with Leg (G)

Seat (J)

Right Panel with Leg (I)

Back Cushion (E)

Seat Cushion (F)

Noble House Home Furnishings LLC

Page 3 OF 7

Step 2

Step 1

Place the Left Armrest with Leg(H) facedown on a clean, non-marring surface.

Place the Backrest with Leg(G) on the Armrest with Leg(H) being sure to insert dowel on Armrest with

Leg(H) into mounting position on Backrest with Leg(G).

Attach Backrest with Leg(G) to Left Armrest with Leg(H) using Bolts(②), Spring Washers(④) and

Washers(③) with Allen Key(⑤) as shown above.

Do not fully tighten the bolts.

Place the Seat(J) onto the Backrest with Leg(G) and Left Armrest with Leg(H) as shown.

Attach Seat(J) to Backrest with Leg(G) and Left Armrest with Leg(H) using Bolts(②), Spring Washers(④)

and Washers(③) with Allen Key(⑤) as shown above.

Do not fully tighten the Bolts.

Dowel

Noble House Home Furnishings LLC

Page 4 OF 7

Turn the Armchair face down.

Use the Bolt Caps(①) to cover all Bolts.

Step 3

Place the Right Panel with Leg(I) facedown on a clean, non-marring surface.

With the help of your adult partner, place Backrest against Right Panel with Leg(I).

Attach the Right Panel with Leg(I) to Backrest with Leg(G) and Seat(J) using Bolts(②), Spring

Washers(④) and Washers(③) with Allen Key(⑤) as pictured above.

Tighten all Bolts at all joints completely at this stage.

Step 4

Noble House Home Furnishings LLC

Page 5 OF 7

Step 6

Place the Seat Cushion(F) and Back Cushion(E) on the Armchair.

Your Armchair is ready for use.

This Armchair can only be used on a flat, level surface.

Step 5

Place the Armchair on a level surface to check the wobbles.

If the Armchair wobbles, adjust the Levelers on the bottom of the Legs to make it level.

Noble House Home Furnishings LLC

Page 6 OF 7

Noble House Home Furnishings LLC

Page 7 OF 7

Label Picture Description QTY

K Backrest with Leg 1

L

Right Armrest with

Leg

1

Caution : You must read this before you proceed

Right Armchair

Noble House Home Furnishings LLC

Page 1 OF 7

M Left Panel with Leg 1

N Seat 1

E Back Cushion 1

F Seat Cushion 1

Label Picture Description QTY

① Bolt Cap 11

②

Bolt (M6*45mm) 11

③

Washer 11

④

Spring Washer

(Ø16*2mm)

11

⑤

Allen Key 1

Noble House Home Furnishings LLC

Page 2 OF 7

Before Beginning

Assembly:

This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview

of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read

through the instructions below to familiarise yourself with the parts and steps before assembly.

Overview

Right Armrest with Leg (L)

Backrest with Leg(K)

Seat (N)

Left Panel with Leg (M)

Back Cushion (E)

Seat Cushion (F)

Noble House Home Furnishings LLC

Page 3 OF 7

Place the Seat(N) onto the Backrest with Leg(K) and Right Armrest with Leg(L) as shown.

Attach Seat(N) to Backrest with Leg(K) and Right Armrest with Leg(L) using Bolts(②), Spring

Washers(④) and Washers(③) with Allen Key(⑤) as shown above.

Do not fully tighten the Bolts.

Step 1

Place the Right Armrest with Leg(L) facedown on a clean, non-marring surface.

Place the Backrest with Leg(K) on the Armrest with Leg(L) being sure to insert dowel on Armrest with

Leg(L) into mounting position on Backrest with Leg(K).

Attach Backrest with Leg(K) to Left Armrest with Leg(L) using Bolts(②), Spring Washers(④) and

Washers(③) with Allen Key(⑤) as shown above.

Do not fully tighten the bolts.

Step 2

Dowel

Noble House Home Furnishings LLC

Page 4 OF 7

Step 3

Place the Right Panel with Leg(M) facedown on a clean, non-marring surface.

With the help of your adult partner, place Backrest against Right Panel with Leg(M).

Attach the Right Panel with Leg(M) to Backrest with Leg(K) and Seat(N) using Bolts(②), Spring

Washers(④) and Washers(③) with Allen Key(⑤) as pictured above.

Tighten all Bolts at all joints completely at this stage.

Step 4

Turn the Armchair face down.

Use the Bolt Caps(①) to cover all Bolts.

Noble House Home Furnishings LLC

Page 5 OF 7

Page is loading ...

Noble House 15140 Operating instructions

This manual is also suitable for

Noble House 15140 Operating instructions

Related papers

Other documents