APEC Water CS-2500 Installation guide

Brand
APEC Water
Model
CS-2500
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

CS-2500 & CS-2500P Water Filtration System
INSTALLATION INSTRUCTION
& OWNER’S MANUAL
All Rights Reserved © APEC Water Systems
Ver 1.2
C
S
S
-
-
2
2
5
5
00
&
C
S
-2
500
P
P
W
ater Filtration
S
S
yy
s
s
t
t
e
e
m
A
ll Ri
ght
s
R
e
s
er
v
ed © APEC
W
a
t
er
Sy
stem
s
Ver 1.
2
Please keep this Owner’s Manual for future reference.
It contains useful information on how to maintain and care for your
APEC CS-2500 or CS-2500P water filter system.
TABLE OF CONTENT
1. Installation:
Preparation ................................................................... page 1
Components ................................................................... page 2
Installing the system
with new provided water supply line ........................ page 3
with existing water supply line ................................... page 6
2. Maintenance:
Filter change schedule & instructions ...................... page 9
3. Warranty .......................................................................... page 11
Please keep this Owner’s Manual
f
or
f
uture re
f
erence.
It contains use
f
ul in
f
ormation on how to maintain and care
f
or
y
our
A
PEC CS-2500 or CS-2500P water
f
ilter system.
TA
BLE
O
F
C
O
N
TE
N
T
1. In
s
t
a
ll
a
ti
o
n
:
Preparation
...................................................................
page
1
C
omponent
s
...................................................................
page
2
Installing the syste
m
with new provided water supply lin
e
........................
page
3
with existing water supply lin
e
...................................
page
6
2
.
M
aintenance
:
Filter change schedule & instruction
s
......................
page
9
3
.
W
arranty
..........................................................................
page
11
Copyright:
This manual is copyrighted by APEC Inc. Under the copyright laws, this manual may
not be reproduced in any form, in whole or part, without the prior written consent of
APEC Inc. Manual print ver. 1.2, 2018 May.
Thank you for choosing APEC Water Filtration Systems.
You now own the finest water filter in America.
Please read and become familiar with instructions and parts needed before pro-
ceeding with the installation.
BEFORE INSTALLATION:
Inspect the system:
Please take the system and all the components out of the box. Inspect the system and
all the connection fittings carefully, make sure nothing is damaged during shipping. If
any part is cracked or broken, please do not proceed with the installation and con-
tact APEC or your distributor for an exchange or diagnosis.
Recommended tools list:
x Adjustable wrench, pliers
x Phillips screwdriver
x Utility knife, or scissors
x Teflon tape
Operating Parameter
x Operating pressure: 90 psi maximum
x Feed water temperature: 35 – 100 degree F (2-37 degree C)
x Do not connect this unit to hot water source
x Install the system in a sheltered environment, avoid exposure to hot and cold
weather or under direct sun light.
General Installation/Operation/Maintenance Requirements
x
Installation needs to comply with state and local laws and regulations.
x System must be installed indoor away from possible environmental damage.
x Do not use with water that is microbiologically unsafe or of unknown quality
without adequate disinfection before or after system. Systems certified for cyst
reduction may be used on disinfected water that may contain filterable cysts.
1
Copyright
:
This manual is copyrighted by APEC Inc. Under the copyright laws, this manual ma
y
not be reproduced in any
f
orm, in whole or part, without the prior written consent o
f
APEC Inc. Manual print ver. 1.2, 2018 May.
Thank
y
ou
f
or choosin
g
APEC Water Filtration S
y
stems.
Y
ou now own the
f
inest water
f
ilter in America.
Please read and become
f
amiliar with instructions and parts needed be
f
ore pro
-
ceeding with the installation.
B
E
FO
RE I
NS
TALLAT
IO
N:
I
nspect the system:
P
lease take the
sy
stem and all the com
po
nents out o
f
the box. In
sp
ect the
sy
stem and
all the connection
f
ittings care
f
ully, make sure nothing is damaged during shipping. I
f
any part is cracked or broken, please do not proceed with the installation and con
-
tact APEC or your distributor
f
or an exchange or diagnosis.
R
eco
mm
e
n
ded
t
oo
l
s
li
s
t:
x
Adjustable wrench, pliers
x
P
hillips screwdrive
r
x
U
tility kni
f
e, or scissors
x
T
eflon tape
T
T
O
perating Parameter
x
Operating pressure: 90 psi maximum
x
F
e
ed water temperature: 35 – 100 degree F (2-37 degree C
)
x
D
o
n
ot
connect this unit to h
ot
water sourc
e
x
I
nstall the system in a sheltered environment, avoid exposure to h
o
t an
d
co
ld
weather or under direct sun light.
G
eneral Installation/O
pe
ration/Maintenance R
eq
uirement
s
x
I
nstallation needs to comply with state and local laws and regulat
i
o
n
s
.
x
System must be installed indoor away
f
rom possible environmental damag
e.
x
D
o not use with water that is microbiologically unsa
f
e or o
f
unknown quality
without adequate disin
f
ection be
f
ore or a
f
ter system. Systems certi
f
ied
f
or cyst
reduction may be used on disin
f
ected water that may contain
f
ilterable cysts.
Components included with the system:
Make sure you have all these parts before starting installation.
Filter Cartridge
w/ Cap & Fittings x 1
Bracket x 1
3/8” Water Supply Line x 2
Bracket Mounting Screw x 4
Important Recommendations:
Space: Make sure there is sufficient space under the counter for installation.
The system is best installed under the kitchen sink. But if that is not feasible
you can install the system anywhere where there is a cold water supply
with sufficient water pressure.
Note: System is primary used as a POU (point of use) system. It is not recom-
mended to connect it on a location that has multiple outlets.
Mounting: Recommend mounting the system on the wall; please leave minimum 6
inch of space underneath the filter to make sure filter cartridge can be
taken down easily for filter replacement.
2
Com
p
onents included with the s
y
stem:
p y
Make sure you have all these parts be
f
ore starting installation.
F
ilter Cartridge
w
/
C
ap & Fittings x
1
B
racket x
1
3
/8” Water Supply Line x
2
B
racket Mounting Screw x
4
I
mportant Recommendations
:
Spac
e
:
Make sure there is su
ff
icient space under the counter
f
or installation.
The system is best installed under the kitchen sink. But i
f
that is not
f
easible
you can install the system anywhere where there is a cold water supply
with su
ff
icient water
pr
essure.
N
ot
e
:
System is primary used as a POU (point o
f
use) system. It is not reco
m
-
mended to connect it on a location that has multiple outlets.
M
ounting
:
Recommend mounting the system on the wall; please leave minimum 6
i
nch o
f
space underneath the
f
ilter to make sure
f
ilter cartridge can be
taken down easily
f
or
f
ilter replacement.
1st Line
IN
2nd Line
OUT
INSTALLING THE SYSTEM WITH NEW PROVIDED WATER SUPPLY LINE
Connect one end of the 1st water
supply line to the side of the cap
that indicate “IN”.
Connect one end of the 2nd water
supply line to the side of the cap
that indicate “OUT”.
Step 1: Connecting The Water Supply Line to the Cap
Sample Connection Diagram
2nd Water Supply Line
1st Water Supply Line
1
2
Step 2: Mounting the Bracket
Hold the system with the filter label side facing you.
Look on top of the cap to make sure the arrow is
pointing towards your right. That arrow indicates
the water flow direction.
Screw the bracket to the top of the system cap with
the front end facing the same side as the filter label.
Please use the front holes for the two screw holes on
the backside.
3
6”
OUTIN
3
1st Water Supply Line
1st Li
ne
IN
2nd Line
OU
T
Conne
c
t one end o
f
the
1
st water
supply lin
e
to the side o
f
the cap
that indi
c
ate “I
N
”.
Conne
c
t one end o
f
the 2nd water
supply lin
e
to the side o
f
the cap
that indi
c
ate “
OU
T
”
.
Step 1: Connecting The Water Supply Line to the Ca
p
Sample Connection Diagra
m
2nd Water Supply Lin
e
1
1
2
IN
S
TALLIN
G
THE
S
Y
S
TEM WITH NEW PR
O
VIDED WATER
SU
PPLY LIN
E
Step 2: Mounting the Bracke
t
H
old the system with the
f
ilter label side
f
acing you.
Look on to
p
o
f
the c
ap
to make sure the arrow is
pointing towards your right. That arrow indicates
the water
f
low direction.
Screw the bracket to the top o
f
the system cap with
the
f
ront end
f
acing the same side as the
f
ilter label.
P
lease use the
f
ront holes
f
or the two screw holes on
th
e
ba
c
k
si
de
.
3
6
”
O
U
T
I
N
1st Water Su
pp
y
Line
s
t Water Su
pp
l
y
Lin
e
Option: With the appropriate nails or hanger, mount the
system to the wall. Make sure to mount the system close
enough to connect to both the cold water valve and
connector to the faucet. Leave minimum 6 inch of space
underneath the filter for filter change.
4
Step 3: Disconnecting the Existing Cold Water Supply Line
Locate the Cold water supply valve under the kitchen
sink (the round or oblong handle on the right side).
Turn off the incoming cold water completely by turning
the shut off handle clockwise.
Note: If the cold water shut off valve cannot turn
off the water, the main water supply to the house
must be shut off for the installation.
5
Turn the faucet handle to
the ON position to release
the remaining water.
Disconnect and remove
the existing fittings and
hose from the cold water
supply valve to the faucet.
6
7
4
O
ption: With the appropriate nails or hanger, mount the
s
ystem to the wall. Make sure to mount the system close
e
nough to connect to both the cold water valve and
c
onnector to the
f
aucet. Leave minimum 6 inch o
f
space
underneath the
f
ilter
f
or
f
ilter change.
4
Step 3: Disconnecting the Existing Cold Water Supply Lin
e
L
o
c
ate the
Co
l
d
water supply valve under the kitchen
s
ink (the round or oblong handle on the right side).
Turn o
ff
the incoming cold water completely by turning
the shut o
ff
handle clockwise.
N
ote
:
I
f
the cold water shut o
ff
valve cannot turn
off
the water, the main water supply to the house
m
us
t
be
s
h
u
t
off
fo
r th
e
in
s
t
a
ll
a
ti
o
n.
5
Turn the
f
au
c
et handle to
th
e
ON
position to release
the remaining water.
D
isconnect and remove
the existing
f
ittings and
ho
se
f
ro
m
th
e
co
ld
w
at
er
s
upply valve to the
f
aucet.
6
7
Sink Faucet
Cold Water Input
2nd Line
Cold Water Valve
1st Line
Connect the end of the 1st line to
the cold water valve that has the
other end connected to the side of
the cap that indicate “IN”.
Connect the end of the 2nd line to
the sink faucet cold water input
that has the other end connected
to the side of the cap that indicate
“OUT”.
Step 4: Connecting The System
8
9
Turn on feed water:
Slowly, turn on your
Cold water supply. Turn
counter-clockwise to
allow the raw water to
enter the system.
Check for leaks! Turn on the cold water
faucet and let it flush
the new system for up
to 5 minutes.
10
11
12
Congratulations! You have successfully installed the APEC Water Filtration System!
Step 5: System Start-Up
5
Sink F
au
ce
t
Co
l
d
Wa
ter Inpu
t
2n
d
Li
ne
Co
ld
Wa
te
r
Va
lv
e
1
st L
i
n
e
Conne
c
t the end o
f
the 1st line to
the cold water valv
e
that has the
o
ther end
c
onne
c
ted to the side o
f
the cap that indicate “I
N
”.
Connect the end o
f
the 2nd line to
th
e
sink
f
aucet cold water inpu
t
that has the other end connected
to the side o
f
the cap that indicate
“
O
UT
”
.
Step 4: Connecting The Syste
m
8
9
T
urn on
f
eed water:
Slowly, turn on you
r
Cold water supply. Turn
counter-clockwis
e
t
o
allow the raw water to
e
nter the
sy
stem.
C
h
ec
k
fo
r l
ea
k
s!
Turn on the cold wate
r
f
aucet and let it
f
lush
the new system
f
or up
to
5
minutes.
1
0
11
11
1
2
C
ongratulations! You have success
f
ully installed the APEC Water Filtration System
!
Step 5: System Start-U
p
INSTALLING THE SYSTEM WITH EXISTING WATER SUPPLY LINE
Step 1: Disconnecting the Existing Cold Water Supply Line
1
Locate the Cold water supply valve under the kitchen
sink (the round or oblong handle on the right side).
Turn off the incoming cold water completely by turning
the shut off handle clockwise.
Note: If the cold water shut off valve cannot turn
off the water, the main water supply to the house
must be shut off for the installation.
Turn the faucet handle to
the ON position to release
the remaining water.
Disconnect the existing water
supply line from the cold wa-
ter supply valve to the faucet.
2
3
Sample Connection Diagram
Existing Water Supply Line
1st Water Supply Line
6”
OUTIN
6
1st Water Supply Line
IN
S
TALLIN
G
THE
S
Y
S
TEM WITH EXI
S
TIN
G
WATER
SU
PPLY LINE
Step 1: Disconnecting the Existing Cold Water Supply Lin
e
1
L
o
c
ate the
Co
l
d
water supply valve under the kitchen
s
ink (the round or oblong handle on the right side).
Turn o
ff
the incoming cold water completely by turning
the shut o
ff
handle clockwise.
N
ote
:
I
f
the cold water shut o
ff
valve cannot turn
off
the water, the main water supply to the house
m
us
t
be
s
h
u
t
off
fo
r th
e
in
s
t
a
ll
a
ti
o
n.
Turn the
f
au
c
et handle to
the
ON
position to release
the remaining water.
D
isconnect the existing wate
r
s
upply line
f
rom the cold w
a
-
ter supply valve to the
f
aucet
.
2
3
Sample Connection Diagra
m
Existing Water Supply Lin
e
6”
O
UT
IN
1
st Water Supply Lin
e
1st Line
IN
Existing water
supply line
OUT
Connect one end of the 1st new
water supply line to the side of
the cap that indicate “IN”.
Connect the existing water
supply line to the side of the
cap that indicate “OUT”.
Step 2: Connecting The Water Supply Line to the Cap
4
5
Step 3: Mounting the Bracket
Hold the system with the filter label side facing you.
Look on top of the cap to make sure the arrow is
pointing towards your right. That arrow indicates
the water flow direction.
Screw the bracket to the top of the system cap with
the front end facing the same side as the filter label.
Please use the front holes for the two screw holes on
the backside.
6
Option: With the appropriate nails or hanger, mount the
system to the wall. Make sure to mount the system close
enough to connect to both the cold water valve and
connector to the faucet. Leave minimum 6 inch of space
underneath the filter for filter change.
7
7
1st Line
IN
Existing water
supply line
OU
T
Conne
c
t one end o
f
the
1
st new
water su
pp
ly lin
e
to the side o
f
the cap that indicate “I
N
”.
Connect the
e
x
i
st
i
ng water
supply lin
e
t
o
th
e
s
i
de
of
th
e
c
ap that indicate “
O
UT
”
.
Step 2: Connecting The Water Supply Line to the Ca
p
4
4
5
Step 3: Mounting the Bracke
t
H
old the system with the
f
ilter label side
f
acing you.
Look on top o
f
the cap to make sure the arrow is
pointing towards your right. That arrow indicates
the water
f
low direction.
Screw the bracket to the top o
f
the system cap with
the
f
ront end
f
acing the same side as the
f
ilter label.
P
l
ea
se
u
se
t
he
f
ro
nt h
ol
es
f
or
t
he
t
wo
s
cr
ew
h
ol
es
o
n
the backside.
6
O
ption: With the appropriate nails or hanger, mount the
s
ystem to the wall. Make sure to mount the system close
e
nough to connect to both the cold water valve and
c
onnector to the
f
aucet. Leave minimum 6 inch o
f
space
underneath the
f
ilter
f
or
f
ilter change.
7
Cold Water Valve
1st Line
Connect the end of the 1st line to
the cold water valve that has the
other end connected to the side of
the cap that indicate “IN”.
Step 4: Connecting The System
8
Make sure the water filter is in LOCK POSITION with the cap. If the filter is
loose or comes off, please reconnect the filter to the cap and turn COUNTER-
CLOCKWISE until it is lock.
In Lock Position Not In Lock Position Not In Lock Position
8
Co
l
d
Wa
ter V
a
lve
1
st Lin
e
Connect the end o
f
the 1st line to
th
e
cold water valv
e
th
a
t h
as
th
e
o
ther end connected to the side o
f
the cap that indicate “I
N
”
.
Step 4: Connecting The Syste
m
8
M
ake sure the water
f
ilter is in LOCK POSITIO
N
with the cap. If the filter is
l
oose or comes o
ff
, please reconnect the
f
ilter to the cap and turn
C
O
U
N
T
E
R
-
C
LOCK
W
IS
E
until it is lock.
In L
oc
k P
os
iti
on
N
o
t In L
oc
k P
os
iti
on
N
o
t In L
oc
k P
os
iti
on
Turn on feed water:
Slowly, turn on your
Cold water supply. Turn
counter-clockwise to
allow the raw water to
enter the system.
Check for leaks! Turn on the cold water
faucet and let it flush
the new system for up
to 5 minutes.
9
10
11
Congratulations! You have successfully installed the APEC Water Fil-
tration System!
* * * End Installation Section * * *
Step 5: System Start-Up
9
T
urn on
f
eed water
:
Slowly, turn on you
r
Cold water supply. Turn
counter-
cl
oc
kw
is
e
t
o
allow the raw water to
e
nter the system.
C
heck
f
or leaks
!
Turn on the cold wate
r
f
au
c
et and let it
f
lush
the new system
f
or up
to
5
minutes.
9
1
0
10
11
C
on
g
ratulations! You have success
f
ull
y
installed the APEC Water Fil-
tration System
!
* * * End Installation Section * *
*
Step 5: System Start-U
p
Locate the Cold water supply valve under the kitchen
sink (the round or oblong handle on the right side).
Turn off the incoming cold water completely by turning
the shut off handle clockwise.
Note: If the cold water shut off valve cannot turn
off the water, the main water supply to the house
must be shut off for the installation.
Turn the faucet handle to the ON position of cold wa-
ter side to release the remaining water and relief the
built-up pressure inside the system.
Hold on to the system and remove the filter by turning
Clockwise and gently pull down to remove the filters.
To prevent spills, hold the filter in an upright position.
Lay the old filter on a towel to absorb any water that
drips out.
SYSTEM MAINTENANCE
The system requires very little maintenance. Just change the filter cartridges regularly
as indicated on the filter label (Replacement time may vary based on the condition
of source water). Keep the system indoors away from extreme heat or cold tempera-
tures, and run the system within its reasonable output capacity (i.e. allow the system
to rest at least a few hours a day).
To properly maintain your APEC water filtration system, please use only genuine APEC
Water replacement filters at www.FreeDrinkingWater.com/filters
1
2
3
Filter Change Instruction
10
L
ocate the
C
old water supply valve under the kitchen
s
ink (the round or oblong handle on the right side).
Turn o
ff
the incoming cold water completely by turning
th
e
sh
ut
o
ff
h
an
dl
e
cl
oc
kw
is
e.
N
ote
:
I
f
the cold water shut o
ff
valve cannot turn
off
the water, the main water su
pp
ly
to the house
m
us
t
be
s
h
u
t
off
fo
r th
e
in
s
t
a
ll
a
ti
o
n.
Turn the
f
aucet handle to the
ON
position o
f
cold wa
-
ter side to release the remaining water and relie
f
the
built-up pressure inside the system.
H
old on to the system and remove the
f
ilter by turning
C
lockwis
e
and gently pull down to remove the
f
ilters.
To
p
revent s
pi
lls, hold the
f
ilter in an u
pr
ig
ht
p
osition.
L
ay the old
f
ilter on a towel to absorb any water that
drips ou
t.
S
Y
S
TEM MAINTENAN
C
E
The system requires very little maintenance. Just change the
f
ilter cartridges regularly
as indicated on the
f
ilter label (Re
pl
acement time may vary based on the condition
of
source wate
r)
. Ke
ep
the s
ys
tem indoors aw
ay
f
rom extreme heat or cold tem
pe
r
a
-
tures, and run the system within its reasonable output capacity (i.e. allow the system
to rest at least a
f
ew hours a day).
To properly maintain your APEC water
f
iltration system, please use only genuine AP
EC
Water replacement
f
ilters a
t
www.FreeDrinkingWater.com/
f
ilters
1
2
3
Filter Change Instructio
n
Turn on feed water:
Slowly, turn on your
Cold water supply. Turn
counter-clockwise to
allow the raw water to
enter the system.
Check for leaks! Turn on the cold water fau-
cet and let it flush the new
system for up to 5 minutes.
Hold on to the new filter with the label side facing you and
align the two teeth indent to the two teeth on the cap. Af-
ter the filter and the cap is align, gently push up and turn
Counterclockwise until it locks in place. Gently pull
down to make sure the filter is secure in place.
4
5
6
7
* * * End Filter Change Section * * *
11
T
urn on
f
eed water
:
Slowly, turn on you
r
Cold water supply. Turn
co
un
te
r-
cl
oc
kw
is
e
t
o
allow the raw water to
e
nter the system.
C
h
ec
k
fo
r l
ea
k
s!
Turn on the cold water
f
au
-
c
et and let it
f
lush the new
s
ystem
f
or up to 5 minutes.
H
old on to the new
f
ilter with the label side
f
acing you and
align the two teeth indent to the two teeth on the cap. A
f
-
ter the
f
ilter and the cap is align, gently push up and turn
Cou
nt
e
r
c
l
oc
kwi
se
until it locks in place. Gently pull
d
own to make sure the
f
ilter is secure in plac
e.
4
4
5
6
6
7
* * * End Filter Change Section * *
*
LIMITED PRODUCT WARRANTY
Scope
APEC takes pride in selling a superb line of products, including this water filtration system (“Product”). As such,
APEC expressly warrants to the original purchaser that, for a period of six (6) months from the date of pur-
chase, the Product will be reasonably free of defects in materials and workmanship. Within that six (6) month
period from the original purchase, APEC will, at its option, repair or replace the Product without charge, or
refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufac-
turing defect within the warranty period, subject to the limitations and exclusions set forth in this Limited Product
Warranty.This Limited Product Warranty only applies when the Product is used, stored, handled, fabricated and/
or installed in the manner recommended by APEC in the Installation Instruction & Owner’s Manual (“Manual”).
Repair or Replacement
Repair or replacement during this six (6) month warranty shall include reasonable labor charges necessary to
repair or replace the defective Product, but shall not include freight charges or any other local labor charges
from third parties other than APEC, unless APEC expressly approves such charges in writing. During the entire
six (6) month warranty, APEC’s obligation to repair or replace shall further be limited to repair or replacement
with the styles, models, products, colors, etc. of the Product that are available at the time of the repair or
replacement, and shall be limited to the repair or replacement of only the specific Product that fails due to a
manufacturing defect. Any repaired or replaced product shall also remain subject to the original six (6) month
warranty from the date of the original purchase, and any repair or replacement shall not extend the original
warranty period in any manner or start a new warranty period.
Conditions of Validity of this Limited Product Warranty
Even though the Product has extremely high endurance for operating conditions such as pH, maximum TDS,
temperature, and optimum water pressure, THIS LIMITED PRODUCT WARRANTY SHALL ONLY BE VALID IF:
1. The replaceable filters are changed and maintained on a regular basis as directed in the Manual. More-
over, depending on local water input water quality, regular maintenance may need to be increased.
2. The Product is operated within the confines of the following standard operating conditions:
Water Pressure Water Temperature
Water Filtration System 20 - 90 psi 35-100 F
Any information or suggestion by APEC with respect to the Product concerning applications, specifications or
compliance with codes and standards is provided solely for your convenient reference and is made without
any representation as to accuracy or suitability. You must verify and test the suitability of any information with
respect to the Product for your specific application.
Non-Covered Defects
THIS LIMITED PRODUCT WARRANTY DOES NOT COVER DEFECTS CAUSED BY:
1. Improper storage, installation, maintenance, handling, use and/or alterations of the Product, including,
but not limited to, non-compliance with the installation, maintenance and standard operation conditions
stated in the Manual and this Limited Product Warranty.
2. Unreasonable use, unintended use, or misuse of the Product for something other than its intended pur-
pose as a reverse osmosis system.
3. Use of replacement parts, filters, membranes or other accessories that are not sold or manufactured by
APEC for use with this particular Product.
4. Damage not resulting from manufacturing defects that occur while the Product is in the original purchas-
er’s possession.
5. Installation of the Product with known or visible manufacturing defects at the time of installation.
6. Damage caused by freezing, flood, fire or Act of God.
12
Scope
p
APEC takes pride in selling a superb line o
f
products, including this water
f
iltration system (“Product”). As such,
APEC expressly warrants to the original purchaser that,
f
or a period o
f
six (6) months
f
rom the date o
f
pu
r
-
c
hase, the Product will be reasonably
f
ree o
f
de
f
ects in materials and workmanship. Within that six (6) month
period
f
rom the original purchase, APEC will, at its option, repair or replace the Product without charge, o
r
re
f
und the cost o
f
the Product, i
f
the Product
f
ails or does not per
f
orm as warranted solely due to a manu
f
ac
-
turing de
f
ect within the warranty period, subject to the limitations and exclusions set
f
orth in this Limited Product
Warranty.This Limited Product Warranty only applies when the Product is used, stored, handled,
f
abricated and/
o
r installed in the manner recommended by APEC in the Installation Instruction & Owner’s Manual (“Manual”).
Repair or Replacement
p
p
R
e
pa
ir or re
pl
acement duri
ng
this six
(6
)
month warran
ty
shall include reasonable labor char
ge
s necessar
y
to
repair or replace the de
f
ective Product, but shall not include
f
reight charges or any other local labor charges
f
rom third parties other than APEC, unless APEC expressly approves such charges in writing. During the entire
s
ix (6) month warranty, APEC’s obligation to repair or replace shall
f
urther be limited to repair or replacement
with the styles, models, products, colors, etc. o
f
the Product that are available at the time o
f
the repair o
r
replacement, and shall be limited to the r
ep
air or r
ep
lacement o
f
only the s
pe
ci
f
ic Product that
f
ails due to a
manu
f
acturing de
f
ect. Any repaired or replaced product shall also remain subject to the original six (6) month
warranty
f
rom the date o
f
the original purchase, and any repair or replacement shall not extend the original
warranty period in any manner or start a new warranty period
.
Conditions of Validity of this Limited Product Warranty
yy
E
ven tho
ug
h the Product has extremel
y
hi
gh
endurance
f
or o
pe
rati
ng
conditions such as
pH
, maximum TDS,
temperature, and optimum water pressure, THIS LIMITED PRODUCT WARRANTY SHALL ONLY BE VALID IF
:
1. The replaceable
f
ilters are changed and maintained on a regular basis as directed in the Manual. Mor
e
-
o
ver, depending on local water input water quality, regular maintenance may need to be increased.
2
. The Product is operated within the con
f
ines o
f
the
f
ollowing standard operating conditions
:
W
a
t
e
r Pr
essu
r
e
W
W
ater Temperature
W
W
ater Filtration System
W
20
-
90
ps
i
35
-1
00
F
An
y
in
f
ormation or s
ug
ge
stion
by
APEC with res
pe
ct to the Product concerni
ng
a
pp
lications, s
pe
ci
f
ications o
r
c
ompliance with codes and standards is provided solely
f
or your convenient re
f
erence and is made without
a
ny representation as to accuracy or suitability. You must veri
f
y and test the suitability o
f
any in
f
ormation with
respect to the Product
f
or your speci
f
ic application.
Non-Covered De
f
ect
s
T
HIS LI
M
ITED PRODUCT WARRA
N
TY DOES
N
OT COVER DEFECTS CAUSED BY
:
1. Improper storage, installation, maintenance, handling, use and/or alterations o
f
the Product, including,
but not limited to, non-compliance with the installation, maintenance and standard operation conditions
s
tated in the Manual and this Limited Product Warranty.
2
. Unreasonable use, unintended use, or misuse o
f
the Product
f
or something other than its intended pu
r
-
pose as a reverse osmosis system.
3
. Use o
f
replacement parts,
f
ilters, membranes or other accessories that are not sold or manu
f
actured by
APEC
f
or use with this particular Product.
4
. Damage not resulting
f
rom manu
f
acturing de
f
ects that occur while the Product is in the original purchas
-
er’s possession.
5. Installation o
f
the Product with known or visible manu
f
acturing de
f
ects at the time o
f
installation.
6. Damage caused by
f
reezing,
f
lood,
f
ire or Act o
f
God.
CONDITIONS THAT RENDER THIS LIMITED PRODUCT WARRANTY VOID
THIS LIMITED PRODUCT WARRANTY SHALL BE VOID IF:
1. The Product is not operated in compliance with normal municipal water conditions for which the
particular model of this Product is intended.
2. The person seeking to invoke the warranty is not the original purchaser. That is, this Limited Product
Warranty only extends to original purchasers.
3. The Product is purchased used. That is, this Limited Product Warranty only covers new products.
4. The Product is purchased from someone other than APEC or one of APEC’s authorized dealers.
This is because, unless the Product was sold by APEC or one of its authorized dealers, APEC cannot
verify or guarantee the integrity or authenticity of the Product.
General Conditions
The warranties set forth herein are the only warranties made by APEC in connection with the
product. APEC cannot and does not make any implied or express warranties with respect to
the product, and disclaims all other warranties, including, but not limited to, any warranty of
merchantability or fitness for a particular purpose. Products sold by APEC are sold only to the
specifications specifically set forth by APEC in writing. Other than the limited product warranty
set forth herein, APEC makes no other warranties, express or implied. APEC’s sole obligation
under this warranty shall be repair or replacement of a non-conforming product or parts of the
product, or at the option of APEC, return of the product and a refund of the purchase price.
Buyer assumes all risk whatsoever as to the result of the use of the product purchased, whether
used singularly or in combination with any other products or substances.
No claim by the buyer/owner of any kind, including claims for indemnification, shall be greater
in amount than the purchase price of the products in respect to which damages are claimed.
In no event shall APEC be liable to buyer/owner in tort, contract or otherwise, for any special,
indirect, incidental, consequential, reliance, statutory, special, punitive or exemplary damages,
including, but not limited to, lost profits, loss of use, loss of time, inconvenience, damage to
good will or reputation, or loss of data, even if advised of the possibility of such damages or
such damages could have been reasonably foreseen, in connection with, arising out of, or as
a result of, the sale, delivery, servicing, use or loss of use of the products sold hereunder, or for
any liability of buyer to any third party with respect thereto.
Obtaining Warranty Coverage or General Inquiries
If coverage is available, you may obtain coverage under this Limited Product Warranty by providing
APEC with proof of original purchase, and that you are the original purchaser. For service under this
Limited Product Warranty, you must notify APEC by phone at 1-800-880-4808, by email at techsup-
port@freedrinkingwater.com, or in writing at 1320 S. Johnson Dr., City of Industry, CA 91745. In making
the claim, please provide your name, address, phone number, a description of the product involved, and
an explanation of the defect.
13
C
ONDITIONS THAT RENDER THIS LI
M
ITED PRODUCT WARRANTY VOID
THIS LI
M
ITED PRODUCT WARRA
N
TY SHALL BE VOID IF
:
1.
Th
e
Product is not operated in compliance with normal municipal water conditions
f
or which the
particular model o
f
this Product is intended.
2
.
The person seeking to invoke the warranty is not the original purchaser
.
That is
,
this Limited Product
r
r
Warran
ty
onl
y
extends to ori
gi
nal
pu
rchasers.
3
.Th
e
Product is
pu
rchased used. That is, this Limited Product Warran
ty
onl
y
covers new
p
roducts.
4
.Th
e
Product is purchased
f
rom someone other than APEC or one o
f
APEC’s authorized dealers.
This is because, unless the Product was sold by APEC or one o
f
its authorized dealers, APEC cannot
veri
f
y or guarantee the integrity or authenticity o
f
the Product.
Ge
n
e
r
a
l
Co
n
d
iti
o
n
s
T
he warranties set
f
orth herein are the only warranties made b
y
APEC in connection with the
product. APEC cannot and does not make any implied or express warranties with respect to
the product, and disclaims all other warranties, including, but not limited to, any warranty o
f
merchantability or
f
itness
f
or a particular purpose. Products sold by APEC are sold only to the
speci
f
ications speci
f
ically set
f
orth by APEC in writing. Other than the limited product warranty
set forth herein, APEC makes no other warranties, express or implied. APEC’s sole obligation
u
nder this warranty shall be repair or replacement o
f
a non-con
f
orming product or parts o
f
the
product, or at the option o
f
APEC, return o
f
the product and a re
f
und o
f
the purchase price.
Buyer assumes all risk whatsoever as to the result o
f
the use o
f
the product purchased, whether
u
sed singularly or in combination with any other products or substances.
No claim by the buyer/owner o
f
any kind, including claims
f
or indemni
f
ication, shall be greater
i
n amount than the purchase price o
f
the products in respect to which damages are claimed.
I
n no event shall APEC be liable to buyer/owner in tort, contract or otherwise,
f
or any special,
i
ndirect, incidental, consequential, reliance, statutory, special, punitive or exemplary damages,
i
ncluding, but not limited to, lost pro
f
its, loss o
f
use, loss o
f
time, inconvenience, damage to
good will or reputation, or loss o
f
data, even i
f
advised o
f
the possibility o
f
such damages or
such damages could have been reasonably
f
oreseen, in connection with, arising out o
f
, or as
a result o
f
, the sale, deliver
y,
servici
ng
, use or loss o
f
use o
f
the
pr
oducts sold hereunder, or
f
or
any liability o
f
buyer to any third party with respect thereto.
Obtainin
g
Warran
ty
Cover
ag
e or General I
nq
uiries
gyg q
If
coverage is available, you may obtain coverage under this Limited Product Warranty by providing
APEC with proo
f
o
f
original purchase, and that you are the original purchaser. For service under this
L
imited Product Warranty, you must noti
f
y APEC by phone at 1-800-880-4808, by email at techsu
p
-
port@
f
reedrinkingwater.com, or in writing at 1320 S. Johnson Dr., City o
f
Industry, CA 91745. In making
the claim, please provide your name, address, phone number, a description o
f
the product involved, and
an e
xp
lanation o
f
the de
f
ect.
Advanced Purification Engineering Corp.
1320 S Johnson Drive
City of Industry, CA 91745
For questions or comments please visit our website at:
FreeDrinkingWater.com
For technical support contact us at:
Techsupport@freedrinkingwater.com
1-800-880-4808
Advanced Puri
f
ication Engineering Corp.
1320 S Johnson Driv
e
Ci
ty
o
f
Indust
ry
, CA 91745
For questions or comments
p
lease visit our website at
:
FreeDrinkin
g
Water.co
m
For technical support contact us at
:
T
echsupport@
f
reedrinkingwater.com
1-
800
-
880
-
4808
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

APEC Water CS-2500 Installation guide

Brand
APEC Water
Model
CS-2500
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents