Posiflex CD-3202U/R User manual

Brand: Posiflex

Model: CD-3202U/R

Category: Bar code readers

Type: User manual

The Posiflex CD-3202U/R is an image scanner that offers a variety of features to make scanning barcodes quick and easy. It's highly accurate and can decode most common 1D and 2D barcodes, including damaged or poorly printed ones. The scanner is also durable, built to withstand daily use in retail, healthcare, and other industries.

Package Contents

CD-3202U

 CD-3202U 2D image scanner

 ST-8000 scanner holder stand

(Optional)

 USB cable

 Quick setup guide for CD-

3202U/R

CD-3202R

 CD-3202R 2D image scanner

 ST-8000 scanner holder stand

(Optional)

 RS-232 cable

 Quick setup guide for CD-

3202U/R

Product Overview

Front View

Rear View

18160904010 Ver. A0

http://www.posiflex.com

Trigger Button

Scan

window

Status LED

CD-3202U/R

2D Image Scanner

Quick Setup Guide

Scanner Maintenance

The scanner is designed for long-term trouble-free operation and rarely

requires any maintenance. Only an occasional cleaning of the scanner window

is necessary in order to remove dirt and fingerprints.

Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to

avoid the scan window from being scratched and damaged. The scan window

can be cleaned while the scanner is running.

The standard interface cable is attached to the scanner with a 10-pin modular

connector. When the connector is properly seated, it is secured in the scanner

by a flexible retention tab. The cable is designed to be field replaceable.

Replacement cables can be obtained from your authorized distributor. To

replace the cable, take the following steps.

1. Make sure the power of both the host terminal and the scanner is powered

off.

2. Disconnect the old scanner cable from the host terminal.

3. Press down the retention tab, and gently pull out the cable.

4. Insert the new interface cable into the bottom of the scanner until it clicks.

Then, plug the new cable into the host.

LED Indication

Status

Explanation

Blue LED flashes one time

Good read

Troubleshooting

This section contains information about how to solve problems that you may

encounter when operating the scanner. If a trouble occurs, please refer to the

following diagnostic tips as a mean to solve the trouble. However, before

referring to the tips, make sure that the scanner is installed well. If the problem

remains, contact your dealer.

Problem

Diagnostic Tips

The scanner is on but cannot read

any barcode.

The scanner window is dirty. Clean the scanner

window as described in the Scanner

Maintenance section.

The presented barcode type is not enabled. Use

this guide to tell the scanner to accept that type

of barcode.

The host terminal has disabled the scanner.

Check the setup of host terminal.

The barcode type presented is not supported by

the scanner.

Problem

Diagnostic Tips

The scanner does not accept more

than two or three barcode labels.

Determine whether the required barcode types

are enabled or not.

A stray barcode is sitting somewhere in the

scanner field of view. Remove all barcode labels

from the scanner’s scan volume and try again.

The scanner cannot send the data to the POS

system. Make sure that the scanner is installed

well and your host POS system is ready to

receive data.

A barcode is read by the scanner

but not accepted by the POS

system.

The communication settings of the system port

and the scanner do not match. Adjust the settings

to make them match to each other.

The scanner is not installed well. Contact your

dealer for the proper installation. The software

running on the POS system does not support the

data format of the barcode label.

When a barcode stays close to the

scanner, the barcode cannot be read

automatically by the scanner.

Check whether or not you have enabled the

Manual Trigger mode. If you have enabled this

mode accidentally, please disable the Manual

Trigger mode by scanning the “Disable trigger”

barcode in the advanced user manual.

Programming Codes

Below are some suggestion you need to bear in mind while scanning labels:

1. The barcode labels shown in bold and black are default factory

settings.

2. Please cover the unwanted codes for scanning the specific barcode

required for the programming to prevent confusion in code scanning.

3. Use the user manual downloaded from our global website for advanced

programming.

4. While scanning the setup barcode labels provided in the quick guide, you

need to pull the trigger to initiate the decoding process.

Firmware Version

Scan the below barcode label to retrieve the current firmware version.

Query Firmware Version

Default Settings

Scanning the following barcode can restore the engine to the factory defaults.

Restore All Factory Defaults

USB of Programming Barcodes

Scanning the Enter Setup barcode can enable the engine to enter the setup

mode. Then you can scan a number of programming barcodes to configure

your engine. To exit the setup mode, scan the Exit Setup barcode or a non-

programming barcode, or reboot the engine.

Enter Setup

Exit Setup

USB Interface

There are four options for USB connection:

 USB HID Keyboard: The engine’s transmission is simulated as USB

keyboard input with no need for command configuration or a driver.

Barcode data could be entered by the virtual keyboard directly and it is

also convenient for the host device to receive data.

 USB CDC: It is compliant with the standard USB CDC class

specifications defined by the USB-IF and allows the host device to

receive data in the way as a serial port does. A driver is needed when

using this feature.

 HID POS (POS HID Barcode Scanner): It is based on the HID interface,

with no need for a custom driver. It excels virtual keyboard and

traditional TTL-232 interface in transmission speed.

 IBM SurePOS: It conforms to IBM (now Toshiba Global Commerce

Solutions) 4698 USB scanner interface specifications

When the scanner is connected to both USB and RS-232 ports on a host device,

it will select the USB connection by default.

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

USB HID Keyboard

USB HID-POS

TTL-232

USB CDC

IBM SurePOS (Tabletop)

IBM SurePOS (Handheld)

Trigger Mode

 Level Mode: A trigger pull activates a decode session. The decode

session continues until a barcode is decoded or you release the trigger.

 Sense Mode: The engine activates a decode session every time it detects

a barcode presented to it. The decode session continues until a barcode is

decoded or the decode session timeout expires.

 Continuous Mode: The engine automatically starts one decode session

after another. To suspend/resume barcode reading, simply press the

trigger. Note that when switching to this mode by scanning the

Continuous Mode barcode, the engine will stop barcode reading for 3

seconds before starting scanning continuously.

 Pulse Mode: When the trigger is pulled and released, scanning is

activated until a barcode is decoded or the decode session timeout

expires (The decode session timeout begins when the trigger is released).

 Batch Mode: A trigger pull activates a round of multiple decode sessions.

This round of multiple scans continues until you release the trigger.

Rereading the same barcode is not allowed in the same round.

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

Level Mode

Sense Mode

Continuous Mode

Pulse Mode

Batch Mode

Illumination

A couple of illumination options are provided to improve the lighting

conditions during every image capture:

 Normal

Illumination LEDs on the engine are turned on during image capture.

 Always On

Illumination LEDs on the engine keep on after the engine is powered

on.

 Off

Illumination LEDs on the engine are off all the time.

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

Normal

Always On

Off

Aiming

When scanning/capturing image, the engine projects an aiming pattern which

allows positioning the target barcode whining its field of view and thus makes

decoding easier.

 Normal

The engine projects an aiming pattern only during barcode

scanning/capturing.

 Always On

Aiming pattern is constantly on after the engine is powered on.

 Off

Aiming pattern is off all the time.

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

Normal

Always On

Off

Good Read Beep Volume

There are 20 volume levels to choose from. The bigger the value, the louder

the Good Read Beep.

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

Loud

Medium

Low

Enabling/Disabling of readable codes

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

Enable All Symbologies

Disable All Symbologies

Enable 1D Symbologies

Disable 1D Symbologies

Enable 2D Symbologies

Disable 2D Symbologies

Enable Code 128

Disable Code 128

Enable EAN-8

Disable EAN-8

Enable EAN-13

Disable EAN-13

Enable UPC-E

Disable UPC-E

Enable UPC-A

Disable UPC-A

Enable Interleaved 2 of 5

Disable Interleaved 2 of 5

Enable Matrix 2 of 5

Disable Matrix 2 of 5

Enable Code 39

Disable Code 39

Enable Codabar

Disable Codabar

Enable Code 93

Disable Code 93

Enable GS1-128

Disable GS1-128

Enable GS1 Databar

Disable GS1 Databar

Enable Code 11

Disable Code 11

Enable ISBN

Disable ISBN

Enable ISSN

Disable ISSN

Enable Industrial 25

Disable Industrial 25

Enable Standard 25

Disable Standard 25

Enable Plessey

Disable Plessey

Enable MSI-Plessey

Disable MSI-Plessey

Enable AIM 128

Disable AIM 128

Enable PDF417

Disable PDF417

Enable QR Code

Disable QR Code

Enable Micro QR

Disable Micro QR

Enable Data Matrix

Disable Data Matrix

Enable Rectangular Barcode

Disable Rectangular Barcode

Baud rate settings (Only for CD-3202R)

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

115200

57600

38400

19200

14400

9600

4800

2400

1200

Data, parity and stop bits (Only for CD-3202R)

Before setting, please scan the Enter Setup barcode on P.5.

After setting, please scan the Exit Setup barcode on P.5

7 data bits

8 data bits

No parity

Even parity

Odd parity

1 stop bit

2 stop bits

Specifications

Item

Characteristics

Performance

Image Sensor

640*480 CMOS

Illumination

White LED

Aiming

Red LED (625nm)

Symbologies

PDF417, QR Cord, Micro QR, Data

Matrix

Code 128, EAN-13, EAN-8, Code 39,

UPC-A, UPC-E, Codabar, Interleaved

2 of 5, ITF-6, ITF-14, ISBN, ISSN,

Code 93, UCC/EAN-128, GS1

Databar, Matrix 2 of 5, Code 11,

Industrial 2 of 5, Standard 2 of ,

AIM128, Plessey, MSI-Plessey

Resolution*

≧3mil

Typical Depth of Field*

EAN-13 (13mil): 60mm-350mm

Code 39 (5mil): 40mm-150mm

PDF417 (6.7mil): 50mm-125mm

Data Matrix (10mil): 45mm-120mm

QR Code (15mil): 30mm-170mm

Min. Symbol Contrast*

25%

Scan Angle**

Roll: 360

, Pitch: ±60

, skew: ±60

Field of View

Horizontal 42

, Vertical 31.5

Electrical

Interface

RS-232, USB

*Test conditions: T=23°C Illumination=300lux using incandescent lamp.

**Test conditions: Scan Distance=(min. DOF + max. DOF)/2; T=23°C;

Illumination=300lux using incandescent lamp; 2D: QR Code; 10 Bytes;

Resolution=30mil; PCS=0.8.

※

The product information and specifications are subject to change without

prior notice. To get the detailed information of the CD-3202U/R, please

check this model from Posiflex Global Website. Or download the

advanced manual for more detailed settings.

Posiflex CD-3202U/R User manual

Brand: Posiflex

Model: CD-3202U/R

Category: Bar code readers

Type: User manual

Download PDF

report

Posiflex CD-3202U/R User manual

Posiflex CD-3202U/R User manual

Related papers

Other documents