Zenith VCS442 Installation guide

Installation and Operating Guide | Warranty

Model Number | VCS442 | Video Cassette Recorder

Safety Precautions

This lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

dangerous voltage within the product’s enclo-

sure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the product.

NOTE TO CABLE/TV INSTALLER: This reminder is provided

to call the cable TV system installer’s attention to Article

820-40 of the National Electric Code (U.S.A.). The code

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

the cable entry as practical.

REGULATORY INFORMATION:

FCC Part 15

This product has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the product is operated in a residential installation. This

product generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installa-

tion. If this product does cause harmful interference to

radio or television reception, which can be determined by

turning the product off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

•Increase the separation between the product and

receiver.

• Connect the product into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV tech-

nician for help.

FCC WARNING: This equipment may generate or use radio

frequency energy. Changes or modifications to this

equipment may cause harmful interference unless the

modifications are expressly approved in the instruction

manual. The user could lose the authority to operate this

equipment if an unauthorized change or modification is

made.

FCC COMPLIANCE: The responsible party for this product’s

compliance is:

Marketed and Distributed by LG Electronics U.S.A., Inc.,

1000 Sylvan Avenue, Englewood Cliffs, NJ

Phone: 1-847-941-8000.

IMPORTANT COPYRIGHT INFORMATION: Many television

programs and films are copyrighted. In certain circum-

stances copyright law may apply to private in-home video

taping of copyrighted materials.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS

LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR

MOISTURE.

MOISTURE CONDENSATION

If you pour a cold liquid into a glass, water vapor in the

air will condense on the surface of the glass. This is

moisture condensation. Moisture condensation on the

head drum, one of the most crucial parts of the unit,

will cause damage to the tape. When the VCR is exposed

to a rapid temperature change from cold to warm, some

condensation will occur. Under this condition, connect

the power cord to the AC line, press POWER on and

allow at least two hours for the VCR to dry out.

WARNING: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

SERIAL NUMBER: The serial number is found on the back

of this unit. This number is unique to this unit and not

available to others. You should record requested informa-

tion here and retain this guide as a permanent record of

your purchase.

Model No. ___________________________

Serial No. ___________________________

CONTENTSFEATURES

INTRODUCTION

Features/Contents/Accessories . . . . . . . . . . . . . . . . . .3

Important Safety Instructions . . . . . . . . . . . . . . . . . . . .4

VCR Features Chart . . . . . . . . . . . . . . . . . . . . . . . . . .5

VCR SETUP

Connections for Your VCR . . . . . . . . . . . . . . . . . . . .6-7

Control Names and Locations . . . . . . . . . . . . . . . .8-10

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . .11-12

Onscreen Display (OSD) . . . . . . . . . . . . . . . . . . . . . .13

Setting the Onscreen Menus . . . . . . . . . . . . . . . . . . .14

Setup Menu Features and Operation . . . . . . . . . . . . .15

Channel/Source Selection . . . . . . . . . . . . . . . . . .16-17

Viewing TV Only . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Video Cassette Tapes . . . . . . . . . . . . . . . . . . . . . . . .18

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . .19-20

PLAYBACK

Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . .21-22

Special Effects Playback . . . . . . . . . . . . . . . . . . .23-24

RECORDING

Normal Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . .26-28

Instant Timer Recording . . . . . . . . . . . . . . . . . . . . . .29

Dubbing and Editing . . . . . . . . . . . . . . . . . . . . . . . . .30

ADDITIONAL INFORMATION

EZ Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

VHS Hi-Fi Stereo System/MTS Broadcast . . . . . .32-33

Tape Counter Memory Feature . . . . . . . . . . . . . . . . .34

Editing a Recording . . . . . . . . . . . . . . . . . . . . . . . . . .35

Operating Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Video Head Cleaning . . . . . . . . . . . . . . . . . . . . . . . .35

Controlling Your TV with the Supplied Remote . . . . . .36

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

• Auto Clock Set System

• Energy Save Function

• MTS Hi-Fi Stereo

•1 Year/8 Event Timer with

DAILY and WEEKLY

Functions

• Auto Power and Playback

Functions

• Instant Timer Recording

• Real-Time Tape Counter,

Tape Remaining Time

• Clean Still, Slow, Frame

Advance, Commercial Skip

• Auto Tracking Function/Auto

Head Cleaner

• Onscreen Function Display

•Trilingual Onscreen

Programming Menus

(English/Spanish/French)

Check to make sure that all accessories listed left have been

included with your VCR.

•

Depending on your antenna system, you may need a different

type of Combiner (Mixer) or Separator (Splitter). These are avail-

able at most electronics stores. For further details, see your near-

est authorized service center.

ACCESSORIES

INTRODUCTION

VCR SETUP PLAYBACK

RECORDING ADDITIONAL INFORMATION

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions. - All these safety and

operating instructions should be read before the

product is operated.

2. Keep these instructions. - The safety, operating

and use instructions should be retained for future

reference.

3. Heed all warnings. - All warnings on the product

and in the operating instructions should be

adhered to.

4. Follow all instructions. - All operating and use

instructions should be followed.

5. Do not use this product near water. – For

example: near a bath tub, wash bowl, kitchen

sink, laundry tub, in a wet basement; or near a

swimming pool; and other areas located near

water.

6. Clean only with dry cloth. – Unplug this product

from the wall outlet before cleaning. Do not use

liquid cleaners.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instruc-

tions. -

Slots and openings in the cabinet are pro-

vided for ventilation and to ensure reliable opera-

tion of the product and to protect it from over-

heating. The openings should never be blocked

by placing the product on a bed, sofa, rug or

other similar surface. This product should not be

placed in a built-in installation such as a book-

case or rack unless proper ventilation is provided

or the manufacturer’s instructions have been

adhered to.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9. D

o not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug

has two

blades with one wider than the other.

A grounding

type plug has two blades and a

third grounding prong. The wide blade or the

third prong are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked

on or pinched particularly at plugs, conve-

nience receptacles, and the point where

they exit from the product.

11. Only use attachments/accessories specified

by the manufacturer.

12. Use only with the cart, stand, tripod, brack-

et, or table specified by the manufacturer, or

sold with apparatus. When a cart is used,

use caution when moving the cart/product

combination to avoid injury from tip-over.

13. Unplug this product during lightning storms

or when unused for long periods of time.

14.

Refer all servicing to qualified service per-

sonnel.

Servicing is required when the prod-

uct has been damaged in any way, such as

power-supply cord or plug is damaged, liq-

uid has been spilled or objects have fallen

into the product, the product has been

exposed to rain or moisture, does not oper-

ate normally, or has been dropped.

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S

MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE

REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in

electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the

following procedures for installation, use, and servicing.

This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

INTRODUCTION

VCR FEATURES CHART

This page shows the features of your VCR.

FEATURES VCS442

4-Heads (Special Video Effects) Yes

Full Load/Quick Start Yes

Auto Head Cleaner Yes

Audio System MTS Hi-Fi Stereo

Audio/Video (A/V) Jacks Stereo

Remote Control Yes

Auto/Manual Band Select Yes

Auto/Manual Channel Search Yes

Channel Capability (CATV & TV) 181

Record Speeds SP/SLP Yes

Playback Speeds SP/LP/SLP Yes

Auto Playback System Yes

Auto/Manual Digital Tracking Yes

Instant Recording Yes

Timer-Controlled Recording Yes

Auto Playback Tape Speed Adjust Yes

Slow-Motion Video (4-head VCR) Yes (1/19)

Pause/Still Video Clear

Real-Time Tape Counter Yes

Visual Search Yes

Logic Search Yes

CM Skip Yes

English/Spanish/French Menus Yes

1-Year, 8-Event Timer Yes

Message Center Front Panel Display Yes

Easy Power On Yes

Easy Repeat Yes

Easy Information Yes

Auto Clock Set System Yes

Hook-up Cable (VCR to TV) Yes

Energy Saving Yes

•

VCR design and specifications are subject to change without prior notice.

CONNECTIONS FOR YOUR VCR

Required connections for your VCR.

If you use this connection, tune the TV to the VCR’s RF output channel (Ch 3 or 4).

Turn off power or unplug VCR

before making any connections.

Turn off power or unplug

VCR before making any

connections.

CONNECTIONS WITHOUT A CABLE BOX

CONNECTIONS WITH A CABLE BOX

VCR SETUP

CONNECTIONS FOR YOUR VCR (Cont’d)

Use A/V connections for a better picture.

AUDIO/VIDEO (A/V) CONNECTIONS TO TV

CONNECTIONS WITHOUT A CABLE BOX

Turn off power

or unplug VCR

before making

any connections.

Turn off power

or unplug VCR

before making

any connections.

Accessory

Component:

Another VCR,

Camcorder,

Video Camera,

Satellite Receiver,

Laser Disc Player

VCR SETUP

CONTROL NAMES AND LOCATIONS

FRONT

POWER

To turn the VCR on and off.

While plugged into an AC

outlet, the VCR consumes

1W of electrical power in

OFF condition.

CASSETTE COMPARTMENT

Where the video cassette is inserted.

STOP/EJECT

To stop the tape.

To eject the tape in the VCR.

PLAY

To play back a recorded tape

(page 21).

REW (Rewind)

To rewind the tape during the STOP

mode or for fast reverse picture

search (page 23).

INFRARED REMOTE SENSOR

Receives the signal from the

infrared remote control.

CHANNEL (

)

To scan up or down through

memorized channels (page 16)

or to manually adjust the tape’s

picture onscreen (page 21).

VCR Function Indicator Panel

Details are on the next page.

REC/ITR

To record normally (page 25) or to

activate Instant Timer Recording

(page 29).

P/STILL

To put playback on still (page 23) or

to pause recording (page 25).

FF (Fast Forward)

To advance the tape during the STOP mode

or for fast forward picture search (page 23).

VIDEO IN/AUDIO IN (L/R) JACKS (LINE)

Connect the audio/video output cable from

an external unit (Audio system, TV/Monitor,

Another VCR) to these jacks.

Use INPUT on remote to select an A/V input

channels (AV).

VCR SETUP

CONTROL NAMES AND LOCATIONS (Cont’d)

INDICATOR PANEL

Cassette indicator

Lights while a cassette is

inserted, and flashes while

ejecting a cassette.

Record indicator

VCR indicator

Use TV/VCR on the remote control

to turn this indicator ON or OFF.

ON: for playback, VCR programming

or watching TV programs through the

VCR tuner

OFF: for watching TV programs

through TV tuner

Clock/Tape operation indicator

HI — VCR turned on.

BYE — VCR turned off.

TIMER indicator

AM indicator

(PM is not displayed)

Front Panel Display shows which VCR

function you are using. For example, when

you press SPEED, SP or SLP appears

to indicate the tape speed. As you change

channels, the channel numbers appear. The

current time shows even while the VCR is

off.

Playback Messages

FF (Fast Forward) — Tape is advancing

rapidly.

CUE — Tape is advancing rapidly in

playback mode for visual search.

REV — Tape is reversing rapidly in playback

mode for visual search.

PLAY — Tape is playing at normal playback

speed.

REW (Rewind) — Tape is rewinding rapidly.

SLW — Tape is playing at slow-motion

speed.

STILL — Playback is paused on one frame.

STOP — Tape rewind or playback has

stopped.

Record Messages

RECP — Recording is paused.

SP or SLP — Displays the recording speed.

REC — VCR is recording.

STOP — Recording has stopped.

Tuner Messages

AV — Auxiliary channel is selected for view-

ing equipment connected to Audio/Video

jacks on front of the VCR.

Ch _ — VCR is tuned to Channel _.

HI — VCR turned on.

BYE — VCR turned off.

CONTROL NAMES AND LOCATIONS (Cont’d)

REAR

ANTENNA INPUT CONNECTOR

Connect the VHF/UHF/CATV antenna to this terminal.

AUDIO OUT (L/R) JACKS; Connect these output jacks to the audio input on an external

unit (Audio System, TV/Monitor, Another VCR).

VIDEO OUT JACK; Connect this output jack to the video input terminal on an external unit

(TV/Monitor, Another VCR).

POWER CORD

Connect only to an AC 120V, 60Hz outlet.

VHF/UHF/CATV ANTENNA OUTPUT CONNECTOR

Connect this terminal to the VHF or UHF

antenna terminals on the back of a TV.

VCR SETUP

1. While the VCR is turned off, press and hold CH (

) on the front panel for about five sec-

onds. The VCR will turn itself on and off “RF03” or “RF04” appears in the display window.

2. Use CH (

) on the front panel or CH/TRK (

) on the remote control the RF output

channel (RF03 or RF04).

3. Turn off and on the VCR.

SET THE VCR’s RF output channel

VCR SETUP

REMOTE CONTROL

EJECT

To eject the tape in the VCR (page 18).

TV Control Buttons

You can control the sound level, input source, and

power switch of your LG TV with the supplied remote

(page 36).

STOP

To stop playback or recording (pages 21, 25).

INPUT

Select the VCR’s line input or tuner.

CH/TRK (channel/tracking) (

)

•To scan up or down through memorized channels

(page 16).

•To manually adjust the tape’s picture onscreen

(page 21).

DD EE FF GG

ARROWS

Move up, down, left, right one row, column, or selection

(hold to repeat) (pages 14, 15).

ENTER

Accesses the onscreen menu (page 14).

Displays functions on the TV screen. Switches among

the clock, tape counter and tape remaining modes on

the display (pages 13, 34).

TV/VCR

To view channels selected by the VCR tuner or by the

TV tuner (pages 10, 25).

SLOW

For slow motion playback (pages 24).

ez POWER OFF

See page 31.

CM SKIP

To fast forward picture search through 30 seconds of

recording (page 24).

ez REPEAT

Replays the specified segment twice.

The remote control is used for most of the operations and features of the VCR. Before

proceeding, put batteries in the remote and become familiar with the buttons. Use only type

AAA batteries. The maximum operating distance is about 25 feet.

The POWER, N (PLAY), P/STILL, FF, REW and REC/ITR buttons on the remote control unit

perform the same functions as the corresponding buttons on the VCR. The following buttons

are on the remote control unit only.

NUMBER buttons

Use these buttons, numbered 0-9, to select a channel.

Displays the programming menu on the TV screen.

Quits the current screen or Pop-up, or returns to the

currently tuned channel (pages 14, 16).

CLEAR

Cancels a timer recording (page 28).

Resets tape counter to 0:00:00 (page 34).

VCR SETUP

REMOTE CONTROL (Cont’d)

Aim the remote control at the sensor on the front panel of the VCR.

• The remote control will not operate properly if something

comes between the VCR and the remote control.

• If the effective range is short, try new batteries.

• An object between the VCR and remote control may block the

invisible light beam and operation will be impossible.

• Batteries installed with incorrect polarity may leak and damage

your Remote Control.

• Do not mix old and new batteries or carbon types with alkaline

types.

• Remove the batteries from the battery compartment if the

remote control will not be used for a long period of time.

HOW TO INSTALL THE BATTERIES

REMOTE CONTROL OPERATION

Remove the battery compartment cover.

2. Insert 2 “AAA”-size batteries, match “+” and “-”.

3. Replace the cover.

VCR SETUP

ONSCREEN DISPLAY (OSD)

REM 1:58

PREPARATION

• Turn on the power of both the VCR and TV.

• Tune the TV to the VCR output channel (CH 3 or 4).

• If a direct VIDEO/AUDIO connection is made between the

VCR and the TV, set the TV’s source selector to VIDEO.

Some of these functions will be displayed every time the VCR is

operated.

ONSCREEN FUNCTION DISPLAYS

0:35:40

2:15 PM

STOP CH 4

SP STEREO

JUL 5 , MON 2:15 PM

• The function displays can be seen displayed on the TV screen

for 5 seconds.

• The clock (or tape counter, tape remaining) mode will remain

on the screen until you press ENTER.

• The tape counter and the remaining tape length indicator

appear only when a cassette is inserted. Also, the remaining

tape length indicator appears after any tape operation.

PLAY HI-FI CH 4

SP STEREO

JUL 5 , MON 2:15 PM

FUNCTION DISPLAY

Indicates the function in progress.

HI-FI DISPLAY

Indicates the unit is playing back a tape recorded in HI-FI.

CHANNEL DISPLAY

Indicates the selected channel (or AV).

STEREO/SAP DISPLAY (MONO is not displayed)

Shows the type of audio signal received by the VCR tuner.

TAPE SPEED DISPLAY

Shows the current tape speed.

CLOCK/COUNT/REMAIN DISPLAY

Shows the current time, the tape counter, and remaining time

on the tape.

DATE DISPLAY

Shows the current date. (Month/Date/Day of the week format)

Each press of the ENTER changes the TV screen in the

following sequence.

VCR SETUP

SETTING THE ONSCREEN MENUS

The SETUP, clock setting (Clock Set), and timer recordings

(Program) features are conveniently accessible using the

onscreen menus. The following pages describe the Main and

sub menus.

PREPARATION

• Turn on the power of both the VCR and TV.

• Tune the TV to the VCR output channel (CH 3 or 4).

• If a direct VIDEO/AUDIO connection is made between the

VCR and the TV, set the TV’s source selector to VIDEO.

Use the remote control to adjust the VCR’s features.

CLOCK SET (pages 19-20)

PROGRAM (pages 26-28)

TUNING (pages 16-17)

SETUP (page 15)

MENU SELECTION

MAIN MENU

1. Press MENU and the MAIN menu will appear.

2. Select the desired menu with the

button and then

press ENTER.

• Menus remain on the screen for 3 minutes.

VCR SETUP

SETUP MENU FEATURES AND OPERATION

SETUP MENU

Use

to choose a

desired option on the

SETUP menu. Then use

to choose a

desired setting.

The onscreen display of this VCR can be turned on or off.

The onscreen programming menus of this VCR can be displayed

in either English, Spanish, or French.

The VCR has two separate audio playback systems, the high quality

VHS Hi-Fi system and standard NORMAL mono system. The same

audio is generally recorded on both systems. The VHS Hi-Fi system

plays on separate (left and right) channels, and the NORMAL system

plays monaural sound. The normal track is always played so the

cassette can be played on a VCR that does not have VHS Hi-Fi.

Multichannel Television Sound (MTS) carries stereo and/or

Second Audio Program (SAP) bilingual signals. Set this display

to the desired position when both MTS stereo and SAP signals

are received. When only one of the MTS signal is received, the

VCR automatically selects the corresponding receiving mode

(Stereo or SAP) regardless of the selected position.

For normal operation, the display should be in the STEREO posi-

tion. The VCR will then record a STEREO program when available,

and record a mono program if the program is NOT IN STEREO.

• For weak STEREO and/or SAP broadcasts, changing the dis-

play to mono may give clearer sound.

Used during playback [when AUDIO MODE display (HI-FI/NOR-

MAL) is in HI-FI position] for selecting the audio output signals from

the AUDIO OUT terminals (L ch and R ch), and VHF/UHF/CATV.

This display setting should normally be left in the stereo position,

so that when a stereo tape is played, the stereo sound will be

heard through the left and right channels. If a mono tape is

played and the audio output is set to stereo, the same mono

sound will be heard from both left and right channels.

AUDIO OUTPUT DISPLAY (STEREO/LEFT/RIGHT)

BROADCAST TYPE DISPLAY (STEREO/SAP/MONO)

AUDIO MODE DISPLAY

LANGUAGE SELECT

FUNCTION OSD

Go to the AUDIO MODE option and select HI-FI or NORMAL

using

Go to the BROADCAST TYPE option and select STEREO,

SAP, or MONO using

Go to the AUDIO OUTPUT option and select STEREO, LEFT,

or RIGHT using

Go to the LANGUAGE SELECT option and select ENGLISH,

SPANISH, or FRENCH using

Set up the FUNCTION OSD option by selecting ON or OFF

using

MAIN MENU

VCR SETUP

CHANNEL/SOURCE SELECTION

This VCR is equipped with a frequency synthesized tuner capa-

ble of receiving up to 181 channels. These include VHF chan-

nels 2-13, UHF channels 14-69 and CATV channels 1-125.

PREPARATION

• Connect the VCR to the desired type of antenna or cable TV

system, as shown in ANTENNA TO VCR CONNECTIONS and

CABLE ANTENNA (CATV) CONNECTION (page 6).

• Switch on the power to the VCR and TV.

• Tune the TV to the VCR output channel (CH 3 or 4).

Press

repeatedly to select TUNER, AV.

• The tuner will automatically cycle through all available chan-

nels (TV/CATV) in the area and place them in the tuner’s

memory.

• After the AUTO CHANNEL SET is complete, the TUNING

menu will hide and return to the TV screen automatically.

AUTO CHANNEL PROGRAMMING

1. Press MENU and the MAIN menu will appear.

2. Use

to select the TUNING menu option, then press

ENTER. The TUNING menu will appear.

3. Use

to choose the SOURCE SELECT option, then Use

to select TUNER.

4. Use v/V to choose the AUTO CHANNEL SET option, then

press b/B to set the channel.

5. Make sure the TUNING BAND is set appropriately (TV or

CATV).

• TV : If you are using a standard antenna to receive channels.

CATV : If you are using basic cable to receive channels.

• Change the setting of TUNING BAND to check the TV channels.

6. Use CH/TRK (v/V) on the remote control or CH (V/v) on

the front panel to cycle the VCR through the channels in

memory.

VCR SETUP

CHANNEL SELECTION (Cont’d)

You don’t need to disconnect the VCR from the TV to watch TV

separately. When the VCR’s power is OFF, or when the VCR’s

power is ON and the TV/VCR selector is set to TV, the TV will

operate as if it were connected directly to the antenna or cable.

• The power cord must be plugged into an AC outlet.

• To view or record cable TV programs with the VCR, the VCR’s

TUNING BAND option must be set to CATV (TUNING menu).

• Do not place the VCR directly on top of the TV. This may

cause interference in the picture and sound (of the VCR) dur-

ing the recording or playback mode. If this interference

occurs, move the VCR away from the TV.

Turn on the TV and tune it to the

channel that you wish to watch.

Set POWER to OFF.

This feature allows you to add or erase channels from memory

manually.

Repeat steps 3 and 4 to add or erase channels.

TO ADD OR ERASE CHANNELS FROM MEMORY

VIEWING TV ONLY

MAIN MENU

TUNING MENU

1. Press MENU and the MAIN menu will appear.

2. Use

to select the TUNING menu option, then press

ENTER. The TUNING menu will appear.

3. Use

to choose the CH. ADD/DEL option. Use

select a channel to add or erase.

4. Use ENTER to add or erase the channel.

5. Press MENU to return to the TV screen.

VCR SETUP

VIDEO CASSETTE TAPES

This VCR will operate with any video cassette which has

the mark. The table below shows the recording/playback

time of VHS cassettes when they are used in the SP, LP and

SLP speeds. (LP speed is for playback only.)

• Do not expose video cassettes to extreme heat, high

humidity, or strong magnetic fields.

• Do not tamper with the cassette mechanism.

• Do not touch the tape with your fingers.

• Always store an unused cassette in its case.

Hold the cassette with the arrow side up (top). Insert the

cassette gently into the slot in the direction of the arrow (on the

cassette) until the loading mechanism automatically pulls the

cassette into the unit. Make certain that the cassette is inserted

correctly.

• If the cassette is not loaded correctly, the VCR will eject the

cassette automatically after approximately 3 seconds.

Press STOP/EJECT twice or press EJECT on the remote

control. The cassette will be ejected automatically. After the

cassette is visible in the tape slot, pull it out to remove it.

• Unloading the cassette is possible only when the power cord

is connected to the wall outlet.

• The cassette can be ejected when STOP/EJECT is pressed,

even if the VCR’s power is OFF.

UNLOADING

WHEN HANDLING VIDEO CASSETTES

TYPE

T-60 T-120 T-160

SPEED

SP MODE 60 mins. 120 mins. 160 mins.

LP MODE 120 mins. 240 mins. 320 mins.

SLP MODE 180 mins. 360 mins. 480 mins.

To prevent accidental era-

sure, remove the tab after

recording.

To record again cover the

hole with vinyl tape.

SAFETY TAB

VCR SETUP

SETTING THE CLOCK

PREPARATION

• Turn on the power of both the VCR and TV.

• Tune the TV to the VCR output channel (CH 3 or 4).

• If a direct VIDEO/AUDIO connection is made between the

VCR and the TV, set the TV’s source selector to VIDEO.

The VCR gives you two ways to set the time and date: the Auto

Clock Feature or manually. The Auto Clock Feature enables the

VCR to set up the clock when the VCR is turned off.

The Auto Clock Set feature is set to ON at the factory. In the ON

setting, the VCR looks for a channel carrying XDS (Extended

Data Services) information. XDS updates the clock using the

Coordinated Universal Time.

If you choose AUTO, the VCR sets the clock using the DST

information broadcast in the signal (channel).

If you choose ON, the VCR sets the clock when the Daylight

Saving Time is started and ended.

If “AUTO” is selected as the time zone, the VCR sets the clock

using the first Coordinated Universal Time information it finds in

a broadcast signal.

AUTO CLOCK SET

• The clock uses the 12-hour system. (Be sure to set AM and

PM correctly.)

• The buttons for setting the clock are on the remote control.

• An illogical date will not be accepted (for example:

February 30).

• The initial Clock Setting is JANUARY 1, 2004, 12:00 AM.

MAIN MENU

CLOCK MENU

1. Press MENU and the MAIN menu will appear.

2. Use

to choose the CLOCK menu option.

Press ENTER and the CLOCK menu will appear.

3. Use

to choose the AUTO CLOCK SET option.

Use

to choose ON.

6. Press MENU when finished.

7. Turn off the VCR to complete auto clock setting.

Things to know before starting

There are cases that the

TV station does not send

or sends wrong date

and/or time information

and the VCR sets the time

incorrectly.

In this case we recom-

mend that you set the

clock manually.

4. Use

to choose the DAYLIGHT SAVING option.

Use

to choose AUTO, ON or OFF.

5. Use

to choose the TIME ZONE option.

Use

to choose the correct time zone (AUTO,

EASTERN, CENTRAL, MOUNTAIN, PACIFIC, ALASKA, or

HAWAII).

VCR SETUP

SETTING THE CLOCK (Cont’d)

CLOCK MENU

Example: JULY 5, 2004 ; 2:15 AM

The day of the week will display automatically.

“AUTO CLOCK SET” must be set to “OFF”. If set to “ON”, an

incorrect date and/or time will be entered again when the VCR

is turned off.

MANUAL CLOCK SET

1. Press MENU and the MAIN menu will appear.

2. Use

to choose the CLOCK menu.

Press ENTER and the CLOCK menu will appear.

3. Use

to choose the month.

4. Use

to choose the DAY option.

Use

to choose the day.

5. Use

to choose the YEAR option.

Use

to choose the year.

6. Use

to choose the TIME option.

Use

to choose the time.

7. Use

to choose the DAYLIGHT SAVING option.

Use

to choose the ON or OFF option.

8. Press MENU when finished.

MAIN MENU

Page is loading ...

Zenith VCS442 Installation guide

Related papers

Other documents