Owner’s Manual
Video
Cassette
Recorder
MODEL SVZ162
SVZ162 LAYOUT 4/7/99 6:41 PM Page 1
Once your purchase is registered, you’re eligible to receive all the privileges of owning this prod-
uct. So complete and return the Warranty Registration Card enclosed with your purchase at
once. And take advantage of these important benefits.
MAC5097
Return your Warranty Registration Card today to
ensure you receive all the
benefits
you’re entitled to.
Warranty
Verification
Registering your product within
10 days confirms your right to
maximum protection under the
terms and conditions of your
warranty.
Owner
Confirmation
Your completed Warranty
Registration Card serves as
verification of ownership in the
event of product theft or loss.
Model
Registration
Returning your Warranty
Registration Card right away
guarantees you’ll receive all
the information and special
offers which you qualify for
as the owner of your model.
Congratulations on your purchase, and
welcome to the “family!”
Dear product owner:
Thank you for your confidence in this product. You’ve selected one
of the best-built, best-backed products available today. And we’ll do
everything in our power to keep you happy with your purchase for
many years to come.
As a member of the SV2000 “family,” you’re entitled to protection
by one of the most comprehensive warranties and outstanding ser-
vice networks in the industry.
What’s more, your purchase guarantees you’ll receive all the infor-
mation and special offers for which you qualify, plus easy access to
accessories from our convenient home shopping network.
And most importantly, you can count on our uncompromising com-
mitment to your total satisfaction.
All of this is our way of saying welcome - and thanks for investing in
an SV2000 product.
P.S. Remember, to get the most from your product,
you must return your Warranty Registration
Card within 10 days. So please mail it to us
right now!
R
E
G
I
S
T
R
A
T
I
O
N
N
E
E
D
E
D
W
I
T
H
I
N
1
0
D
A
Y
S
Hurry!
Know these
safetysymbols
This “bolt of lightning”
indicates uninsulated
material within your unit may
cause an electrical shock. For
the safety of everyone in your
household, please do not
remove product covering.
The “exclamation point”
calls attention to features
for which you should
read the enclosed literature
closely to prevent operating
and maintenance problems.
WARNING: TO PREVENT
FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR
MOISTURE.
CAUTION: To prevent
electric shock, match wide
blade of plug to wide slot, and
fully insert.
ATTENTION: Pour éviter
les chocs électriques, intro-
duire la lame la plus large de
la fiche dans la borne corre-
spondante de la prise et
pousser jusqu’au fond.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
t
s
For Customer Use
Below, enter your product’s model number and serial number, which are located on the rear of the cabinet.
Keep this information for future reference.
Model No. ______________________________________ Serial No. ____________________________
SVZ162 LAYOUT 4/7/99 6:41 PM Page 2
Introduction 3
Features
• Auto Return
• Auto Satellite Link
• Automatic Channel Setup
• Automatic Playback Features
• Automatic Tracking Adjustment
• Display Panel
• Hi-Fi Stereo Sound System
• High Quality (HQ) System
• MTS (Multi-Channel Television Sound) System
• On-Screen Displays in English or Spanish
• One-Touch Recording
• Real-Time Counter
• Remote Control
• Rental Play
• Repeat Play
• Special Effects Playback: Forward and Reverse Searching; Still;
Slow
• Special Search Functions: Index; Time; Quick Find
• Timer Recording
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose
this equipment to rain or moisture.
FCC Warning: Any unauthorized changes or modifica-
tions to this equipment void the user’s authority to oper-
ate it.
This VCR, equipped with a High Quality (HQ) system, is compati-
ble with existing Video Home System (VHS) equipment.
Philips Consumer Electronics Company recommends that you use
only video cassette tapes that have been tested and inspected for
use in two, four, six, and eight hour VCRs, and which are labeled
with the mark. The use of tapes that have not been inspected
for use in two, four, six, and eight hour VCRs may result in poor
picture quality and excessive deposits on the video heads, which
may not be covered by the warranty if damage occurs.
Note to the Cable TV System Installer: This reminder is
provided to call the Cable TV system installer’s attention to
Article 820-40 of the National Electrical Code, which provides
guidelines for proper grounding – in particular, specifying that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as possible.
Copyright 1998 Philips Consumer Electronics Company. All rights
reserved.
Welcome to your VCR owner’s manual.
This manual has seven sections: Setting Up Your VCR; Description of Controls; Basic Operations;
Recording; Playing; Stereo Features; and Information You May Need. The instructions explain all
of the VCR’s features, which are listed below. You cannot hurt your VCR by trying the features!
So read on – and relax.
• Before doing anything else, record
the VCR’s model and serial numbers
in the spaces provided on page two.
These numbers will help us assist
you if you ever call for help.
Helpful Hint
SVZ162 LAYOUT 4/7/99 6:41 PM Page 3
4 Table of Contents
Setting Up Your VCR
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hookups Without a Cable Box/Direct Broadcast System . . . . . . . . . . . . . . . . . . . . .6 - 7
Hookups With a Cable Box/Direct Broadcast System . . . . . . . . . . . . . . . . . . . . . . . .8 - 9
Hookups With a Stereo TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Turning on Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Automatic Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 13
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 - 15
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Description of Controls
On-Screen Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 19
VCR Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Basic Operations
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Recording
One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 - 29
Auto Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Auto Satellite Link Using a Satellite Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Recording One Channel/Watching Another . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Playing
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Special Effects Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Rental Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Real-Time Counter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Quick Find . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Automatic Playback Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Stereo Features
MTS Broadcast Stereo System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 - 43
Hi-Fi Stereo Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Information You May Need
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 - 47
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
SVZ162 LAYOUT 4/7/99 6:41 PM Page 4
Before Using Your VCR 5
Putting Batteries in the Remote Control
● In this VCR, use only tapes with the mark.
● Make sure any light adhesive stick-on notes are removed from
the video cassette tape before putting the tape in the VCR.
Removable labels like these can jam the VCR.
● Periodic maintenance is required to maintain your VCR’s per-
formance. The video heads will eventually require cleaning or
replacement. Cleaning or replacement of the video heads
should be performed by an authorized service center.
1
Remove the battery compartment lid on the bottom of the
remote control by sliding the lid in the direction of the arrow.
2
Insert two AA batteries inside the battery compartment with
their
+
and – ends aligned as indicated.
3
Replace the battery compartment lid.
Using the Remote Control
● Point the remote control at the VCR’s remote sensor (see page
21) when using the remote control to operate the VCR.
● Do not put objects between the remote control and the VCR.
Video cassette tapes have record tabs to ensure that recordings
are not erased accidentally.
1
To prevent accidental erasure, break off the tab with a screwdriv-
er.
2
To record again, cover the hole with cellophane tape.
Erasure Prevention
VCR maintenance
• The remote control and its batteries
are supplied.
• Do not mix alkaline and man-
ganese batteries.
• Do not mix old and new batteries.
Helpful Hints
1
3
2
1
2
SVZ162 LAYOUT 4/7/99 6:41 PM Page 5
CH3
CH4
OUT
IN
ANT
OR
AUDIO
R
L
VIDEO
OUT
IN
IN
OUT
CH3
CH4
OUT
IN
ANT
R
L
VIDEO
IN
OUT
IN
OUT
AUDIO
75V
ANT /
CABLE
OR
6 Hookups Without a Cable Box / Direct Broadcast System
The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a
Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo
TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR.
ANTENNA IN
Jack
(on back of TV)
Cable
(75 ohm)
Back of VCR
Antenna
Indoor/Outdoor
(300 ohm)
1
Disconnect the antenna or cable from your TV.
2
Connect the antenna or cable to the ANT(enna) IN Jack of your VCR.
Cable
(75 ohm)
Antenna
Indoor/Outdoor
(300 ohm)
SVZ162 LAYOUT 4/7/99 6:41 PM Page 6
CH3
CH4
OUT
IN
ANT
CH 4
or
CH 3
CH3 / CH4
Switch
AUDIO
R
L
VIDEO
OUT
IN
IN
OUT
CH3
CH4
OUT
IN
ANT
CH3 CH4
R
L
VIDEO
IN
OUT
IN
OUT
AUDIO
CH3
CH4
OUT
IN
ANT
75V
ANT /
CABLE
75V
ANT /
CABLE
CH3
CH4
OUT
IN
ANT
AUDIO
R
L
VIDEO
OUT
IN
IN
OUT
R
L
VIDEO
IN
OUT
IN
OUT
AUDIO
RF coaxial cable
Antenna
or Cable
3
Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the
VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on
type (supplied) or screw-on type of coaxial cable, whichever you prefer.)
5
Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever
channel is not used or least used in your area. Set the TV to the same channel. For
example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on
channel 03.
Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7
ANTENNA IN Jack
(on back of TV)
example only
4
Plug in the TV and the VCR.
6
You are ready to turn on the VCR. Please go to page 11 before turning on the
VCR.
SVZ162 LAYOUT 4/7/99 6:41 PM Page 7
8 Hookups With a Cable Box / Direct Broadcast System
There are two ways to connect your Cable Box/DBS to the VCR. With this connection:
● You may view any channel.
● You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR.
● You may not view a channel other than the one you are recording.
● You may not program channels at the VCR.
● You can only program a timer recording for one channel at a time. Set the TV and the VCR to the
Cable Box/DBS output channel (channel 03 or 04), and set your Cable Box/DBS to the channel you
want to record. When you enter the channel you want to record in a timer recording, select channel 03
or 04 (the Cable Box/DBS output channel). (This is step 7 on page 28.) Leave the Cable Box/DBS on for
a timer recording.
R
L
VIDEO
IN
OUT
IN
OUT
AUDIO
CH3
CH4
OUT
IN
ANT
OUT
IN
75V
ANT /
CABLE
TV’s
ANTENNA IN
Jack
Cable Box/DBS
VCR
Recording/Viewing Any Channel
Connections
1
With the VCR on and in VCR position (the VCR/TV light will appear on
the display panel), use the CHANNEL o/p buttons to set the
VCR to the Cable Box/DBS output channel (channel 03 or 04).
2
Set the TV to the same channel to which you set the VCR.
3
Select the channel you want to view/record at the Cable
Box/DBS.
1
Connect a Cable signal to the IN Jack on the Cable Box/DBS.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on the
Cable Box/DBS to the ANT(enna) IN Jack on the VCR.
3
Use a second RF coaxial cable to connect the OUT Jack on the VCR to
the TV’s ANTENNA IN Jack.
1
2
3
Cable
Signal
RF coaxial
cable
RF coaxial
cable
SVZ162 LAYOUT 4/7/99 6:41 PM Page 8
Hookups With a Cable Box / Direct Broadcast System (cont’d) 9
R
L
VIDEO
IN
OUT
IN
OUT
AUDIO
CH3
CH4
OUT
IN
ANT
IN
OUT
75V
ANT /
CABLE
With this connection:
● You may watch one channel while recording another.
● You may not record scrambled channels.
Recording One Channel/Watching Another
1
Put the Cable Box/DBS on the same channel as the
VCR’s CH3/CH4 switch. Then, with the VCR in VCR
position (the VCR/TV light will appear on the display
panel), use the CHANNEL o/p buttons to select the
channel you want to record at the VCR. Start the
recording.
2
Press the VCR/TV button once to put the VCR in TV
position. (The VCR/TV light will disappear.)
3
Set the TV to the Cable Box/DBS output channel (03 or
04).
4
Select the channel you want to watch at the Cable
TV’s ANTENNA
IN Jack
Cable Box/DBS
VCR
• When you play a tape, make sure
the Cable Box/DBS is set to the
same channel as the CH3/CH4
switch on the VCR. Set the TV to
the Cable Box/DBS output channel
(03 or 04).
Helpful Hint
1
Connect a Cable signal to the VCR’s ANT(enna) IN Jack.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on
the VCR to the IN Jack on the Cable Box/DBS.
3
Use a second RF coaxial cable to connect the OUT Jack on the
Cable Box/DBS to the ANTENNA IN Jack on the TV.
1
2
3
Connections
Cable
Signal
RF coaxial
cable
RF coaxial
cable
SVZ162 LAYOUT 4/7/99 6:41 PM Page 9
10 Hookups With a Stereo TV
1
Connect the antenna or cable to the ANT(enna) IN Jack
on the back of the VCR.
2
Connect a video cable to the yellow VIDEO OUT Jack on
the back of the VCR. Then, connect the other end of the
video cable to the VIDEO IN Jack on your TV.
3
Connect an audio cable to the red and white AUDIO
OUT Jacks on the back of the VCR. Then, connect the
other end of the audio cable to the AUDIO IN Jacks on
your TV.
4
Turn on your TV, making sure it is in Line Input mode. Please
refer to your TV owner’s manual for details.
• A stereo audio cable (not supplied)
is used here to deliver audio to the
TV’s left and right channels.
• The TVmust be in Line Input mode.
Please refer to your TV owner’s
manual.
Helpful Hints
R
L
VIDEO
IN
OUT
IN
OUT
AUDIO
CH3
CH4
OUT
IN
ANT
antenna or
cable to
ANT(enna)
IN Jack
Video Cable
Audio Cable
VIDEO (yellow) and
AUDIO (red and white) OUT Jacks
Audio and Video
IN Jacks on TV
● Audio and Video cables are not supplied.
1
2
3
SVZ162 LAYOUT 4/7/99 6:41 PM Page 10
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
Turning on Your VCR 11
●Before turning on your VCR, make sure there are batteries in
the remote control and the VCR and TV are connected (see
pages five - 10).
●You can not set up channels if you are using a Cable Box/DBS.
●The instructions on this page only work when you turn on the
VCR for the first time. If there is a power failure or if the VCR
is unplugged for more than one minute, you may need to repeat
the instructions on this page.
1
Press the POWER button. The POWER light and the VCR/TV
light will appear.
2
Turn on the TV. Set it to the same channel as the
CH3/CH4 switch on the back of the VCR. The menu shown
below will appear.
2
1
Turn on the TV.
• If you do not see any on-screen dis-
plays when you turn on the VCR,
check your hookups, then try again.
If you still do not see any on-screen
displays, follow the steps under
“Automatic Channel Setup” on page
12 and “Language Selection” on
page 16.
Helpful Hint
LANGUAGE SELECT
→ ENGLISH [ON]
ESPAÑOL
5
Press the MENU button, the F.FWD button, or the
REWIND button to begin automatic channel setup.
TUNER SET UP will flash on-screen. The VCR will memorize all
available channels, so when you use the CHANNEL o/p buttons,
you’ll only scan through channels that you receive. When channels
are set up, the TV will go to the lowest channel available.
(If you try to set up channels when there is no antenna or cable
connected to the VCR, programming will appear to take place.
Eventually, TUNER SET UP will appear on-screen steadily, and
channel programming will stop. Connect an antenna or cable to
the VCR, then press the MENU button, the F.FWD button, or the
REWIND button again. Channel programming will begin again.)
3
Press the PLAY button or the STOP button to select
ENGLISH or ESPAÑOL. [ON] will appear beside your choice.
4
Press the F.FWD button or the MENU button. TUNER SET
UP will appear on-screen.
TUNER SET UP
5
3
4
SVZ162 LAYOUT 4/7/99 6:41 PM Page 11
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
12 Automatic Channel Setup
Although your VCR may automatically set up the channels you
receive when you turn it on for the first time, this function lets
you set up channels again. Make sure:
●The VCR is on and is in VCR position. (The VCR/TV light will
appear on the display panel. If it does not, press the VCR/TV
button once.)
1
Press the MENU button repeatedly until the INITIALIZE
menu appears.
2
Press the PLAY button or the STOP button repeatedly to
select CHANNEL SET UP. Then, press the F.FWD but-
ton.
3
Press the PLAY button or the STOP button repeatedly to
point to TV (if you have an antenna) or CATV (if you
have a cable connection).
4
Press the F.FWD button once or twice. [ON] will appear
beside your selection, then the VCR will memorize all available
channels. When setup is complete, the lowest channel you receive
will appear on-screen.
• Line Input mode will always be
stored in the VCR’s memory as
channel 00. When you select chan-
nel 00 with the CHANNEL o/p
buttons or the Number buttons,
AUXwill appear on-screen.
• You can not program channels if
you are using a Cable Box/DBS.
Details are on pages eight - nine.
Helpful Hints
1
INITIALIZE
→ CHANNEL SET UP
SETTING CLOCK
LANGUAGE SELECT
CHANNEL SET UP
→ TV [ON]
CATV
ADD/DELETE CH
2
3
4
SVZ162 LAYOUT 4/7/99 6:41 PM Page 12
Automatic Channel Setup (cont’d) 13
2
Press the PLAY button or the STOP button repeatedly to
select CHANNEL SET UP. Then, press the F.FWD but-
ton.
3
Press the PLAY button or the STOP button repeatedly to
select ADD/DELETE CH. Then, press the F.FWD button.
4
Press the Number buttons or press the PLAY button or
the STOP button repeatedly until your desired channel
number appears.
5
Press the F.FWD button or the REWIND button so that
ADD or DELETE flashes on-screen.
6
While your choice is flashing, press the COUNTER
RESET/EXIT button. The channel you added or deleted will
appear. The channel will be added or deleted, whichever was
flashing on-screen when you exited the menu.
ADD / DELETE CH
0 2 (TV)
2-3
CHANNEL SET UP
→ TV [ON]
CATV
ADD/DELETE CH
Adding/Deleting Channels
The channels you no longer receive or seldom watch can be
deleted from the memory. You also may add new channels into
the memory. Make sure:
●The VCR is on and in VCR position. (The VCR/TV light will
appear. If it does not, press the VCR/TV button once.)
1
Press the MENU button repeatedly until the INITIALIZE
menu appears.
1
6
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
4
5
5
SVZ162 LAYOUT 4/7/99 6:41 PM Page 13
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
SETTING CLOCK
MONTH DAY YEAR
0 3 / 0 1 – – – –
HOUR MINUTE AM/PM
– – : – – – –
SETTING CLOCK
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
SETTING CLOCK
MONTH DAY YEAR
0 3 / 0 1 1 9 9 8
HOUR MINUTE AM/PM
– – : – – – –
14 Setting the Clock
Follow the steps below to set your VCR’s clock. Make sure:
● The VCR is on and in VCRposition. (The VCR/TV light will
appear. If it does not, press the VCR/TV button once.)
3
While the MONTH space is flashing, press the PLAY but-
ton or the STOP button repeatedly until the desired
month appears. Then, press the F.FWD button.
4
While the DAY space is flashing, press the PLAY button
or the STOP button repeatedly until the desired day
appears. Then, press the F.FWD button.
5
While the YEAR space is flashing, press the PLAY button
or the STOP button repeatedly until the desired year
appears. Press the F.FWD button. The day of the week will
appear automatically.
• To reset the clock, follow steps 1 -
2 above. Select the information you
want to change using the F.FWD
button or the REWIND button.
When the desired information is
flashing, use the PLAY button or the
STOP button to enter the correct
information. Press the COUNTER
RESET/EXIT button to exit.
• To display the time, press the DIS-
PLAY button repeatedly until the
time appears on-screen.
• Power failures that last for more
than one minute can cause you to
lose your clock setting.
• Press the REWIND button to go
back one step from the current step
during steps 4 - 8.
Helpful Hints
SETTING CLOCK
MONTH DAY YEAR
– – / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
1
2-5
2
Press the PLAY button or the STOP button repeatedly to
select SETTING CLOCK. Then, press the F.FWD button.
1
Press the MENU button repeatedly until the INITIALIZE
menu appears.
SVZ162 LAYOUT 4/7/99 6:41 PM Page 14
SETTING CLOCK
MONTH DAY YEAR
0 3 / 0 1 SUN 1 9 9 8
HOUR MINUTE AM/PM
0 5 : – – – –
Setting the Clock (cont’d) 15
7
While the MINUTE space is flashing, press the PLAY but-
ton or the STOP button repeatedly until the desired
minute appears. Then, press the F.FWD button.
8
While the AM or PM space is flashing, press the PLAY but-
ton or the STOP button repeatedly to point to AM or PM.
6
While the HOUR space is flashing, press the PLAY button
or the STOP button repeatedly until the desired hour
appears. Then, press the F.FWD button.
9
Press the COUNTER RESET/EXIT button or the F.FWD
button to start the clock.
SETTING CLOCK
MONTH DAY YEAR
0 3 / 0 1 SUN 1 9 9 8
HOUR MINUTE AM/PM
0 5 : 4 0 – –
SETTING CLOCK
MONTH DAY YEAR
0 3 / 0 1 SUN 1 9 9 8
HOUR MINUTE AM/PM
0 5 : 4 0 PM AM
→PM
6-7
• If the clock has never been set, the
SETTING CLOCK menu may
appear immediately when you press
the MENU button. If this happens,
follow the instructions from step 3
on page 14.
Helpful Hint
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
8
9
SVZ162 LAYOUT 4/7/99 6:41 PM Page 15
16 Language Selection
Follow the steps below to change the language of the on-screen
menus and displays. Make sure:
● The VCR is on and in VCR position. (The VCR/TV light will
appear. If it does not, press the VCR/TV button once.)
2
Press the PLAY button or the STOP button repeatedly to
select LANGUAGE SELECT. Then, press the F.FWD but-
ton.
3
Press the PLAY button or the STOP button to select
ENGLISH or ESPAÑOL. [ON] will appear beside your choice.
4
Press the COUNTER RESET/EXIT button to exit.
INITIALIZE
→ CHANNEL SET UP
SETTING CLOCK
LANGUAGE SELECT
INITIALIZE
CHANNEL SET UP
SETTING CLOCK
→ LANGUAGE SELECT
LANGUAGE SELECT
→ ENGLISH [ON]
ESPAÑOL
1
Press the MENU button repeatedly until the INITIALIZE
menu appears.
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
1
2
3
• If you accidentally select Spanish
on-screen displays and need English
on-screen displays:
1) Press the MENU button repeatedly
until the PARA INICIAR menu
appears.
2) Press the PLAY button or the STOP
button repeatedly to choose SELEC.
IDIOMA, then press the F.FWD but-
ton.
3) Press the PLAY button or the STOP
button to select ENGLISH.
4) Press the COUNTER RESET/EXIT
button to exit.
Helpful Hint
4
SVZ162 LAYOUT 4/7/99 6:41 PM Page 16
On-Screen Status Displays 17
You may access on-screen status displays by pressing the DISPLAY button repeatedly. On-screen status
displays may include the current time, channel, and other information.
● Press the DISPLAY button once. The COUNT on-screen status display will appear for five seconds. After
five seconds, only the real-time counter will appear on-screen. This counter shows you the elapsed play-
ing time of the tape (from the point at which the real-time counter was set to zero).
● Press the DISPLAY button once again. The CLOCK on-screen status display will appear for five seconds.
After five seconds, only the current time will appear on-screen (the clock must be set). (If you are
watching TV, the current channel number and the availability of stereo or second audio will also appear
on-screen.)
● Press the DISPLAY button once again. The on-screen status display will disappear.
<OFF mode>
<COUNT mode>
STOP
SLP 0:12:34 HIFI
<CLOCK mode>
STOP 5:40 PM
CH 02
STEREO
SAP
SLP
Press the DISPLAY
button once.
• If the channel you select has no
broadcast, the screen will be solid
blue.
• You may bring up a status display
at any time by pressing the DIS-
PLAY button. (The exception is
when viewing a still picture or a
slow motion picture, or when
F.FWD or REWIND is pressed dur-
ing playback.)
• Channel numbers (when tuned)
appear on-screen for a few seconds.
Helpful Hints
Press the DISPLAY button once.
Press the DISPLAY button once.
This indicates that HIFI has been selected at the AUDIO
OUT menu (see page 44 for details). If you play non-Hi-Fi
tapes while the VCR is set to HIFI, or if MONO has been
selected at the AUDIO OUT menu, HIFI will not appear
on the status display.
SVZ162 LAYOUT 4/7/99 6:41 PM Page 17
SLOW Button
Press during tape playback to view a tape in slow motion. Slow
speed can be adjusted by pressing the F.FWD button (faster) or
the REWIND button (slower). Details are on page 35.
18 Remote Control Buttons
MENU Button
Press repeatedly to access menus or to remove menus.
SPEED Button
Press to select the recording speed (SP, LP, or SLP). Details are on
pages 24 and 45.
PLAY Button
Press to play a tape. Also, press to release Slow, Search, or Still
mode and to return to normal playback. Details are on page 35.
Use to enter digits and information when programming a function
in the on-screen menu (setting the clock, for example). Press to
select an item in the on-screen menu.
REWIND Button
When tape playback is stopped, press to rewind the tape at high
speed. During tape playback, press to rewind the tape while the pic-
ture stays on-screen. Details are on page 35.
Press to erase a timer recording. Details are on page 29.
Press to go back one step when setting the clock or a timer recording.
Press to add or delete channel numbers. Details are on page 13.
RECORD Button
Press to start a recording. Details are on page 24.
DISPLAY Button
Press repeatedly to view the on-screen status displays. Details are
on page 17.
Number Buttons
Use to select channels.
Channels 1 - 9 ●
To select, press 0, then press the channel number you want. For
example, to select channel 7, press 0, 7.
Channels 100 and above ●
To select, press the +100 button, then press the last two digits of
the channel you want. For example, to select channel 117, press
the +100 button, 1, 7.
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
QUICK-FIND Button
Press to perform a Quick Find. Details are on page 40.
POWER Button
Press to turn the VCR on or off.
SVZ162 LAYOUT 4/7/99 6:41 PM Page 18
Remote Control Buttons (cont’d) 19
STOP Button
Press to stop the tape.
Use to enter digits and information when programming a function
in the on-screen menu (setting the clock, for example). Press to
select an item in the on-screen menu.
PAUSE/STILL Button
During recording, press to temporarily stop the recording. Press
again to resume recording. Details are on page 24. You can not
pause a One-Touch Recording. Details are on page 25. During tape
playback, press to freeze the picture. Press the PAUSE/STILL but-
ton repeatedly to advance the picture frame by frame. Details are
on page 35.
F.FWD Button
When tape playback is stopped, press to fast forward the tape at
high speed. During tape playback, press to fast forward the tape
while the picture stays on-screen. Details are on page 35.
Press to add or delete channel numbers. Details are on page 13.
CHANNEL o/p Buttons
Press to scan up or down through the VCR’s channels after the
channels have been set up. Details are on page 12.
During slow motion playback, press to adjust the tracking. Details
are on page 41.
COUNTER RESET/EXIT Button
Press to set the real-time counter to zero. Details are on page 37.
Press to remove menus.
VCR/TV Button
Use to select the signal that your TV receives.
● VCR Position
Use to watch a tape, to watch a program while recording it, or to
watch a TV broadcast using the CHANNEL o/p or Number
buttons.
● TV Position
Use to watch TV or to watch one program while recording anoth-
er. Details are on page 32.
COUNTER MEMORY Button
Press to memorize a tape position at which the real-time counter
was set to 0:00:00. Details are on page 37.
EJECT Button
Press to eject the tape.
INDEX SEARCH Button
Press to perform an Index Search. Details are on page 38.
TIME SEARCH Button
Press to perform a Time Search. Details are on page 39.
VCR/TVPOWER EJECT
1 2 3
4 5 6
7 8 9
0 +100
CHANNEL
INDEX
SLOW
SPEED
QUICK-
FIND
TIME
EXIT COUNTERDISPLAY
MENU
RESET MEMORY
REWIND / PLAY F.FWD
RECORD PAUSE/STILL
/ STOP
SEARCH
SVZ162 LAYOUT 4/7/99 6:41 PM Page 19
20 VCR Display Panel
VCR/TVPOWER
POWER
CST. IN TIMER REC
CHANNEL
PLAY
STOP
REW
REC/OTR PAUSE
F.FWD
EJECT
VCR/TV
VCR/TVPOWER
POWER
CST. IN TIMER REC
CHANNEL
VCR/TV
VCR Display Panel
Information about VCR opera-
tions is displayed here.
Cassette Compartment
Insert a video cassette tape here.
VCR/TV Light
This light appears when the VCR
is in VCR position.
REC(ord) Light
This light appears during a recording. It
flashes when a recording is paused.
CST.IN Light
This light appears when a tape is in the VCR.
POWER Light
This light indicates that the power
is on.
TIMER Light
This light glows when you turn off the power to
set a timer recording. It also glows during a
One-Touch Recording. It flashes when you turn
off the power to set a timer recording if a tape
has not been placed in the VCR. It flashes when
all timer recordings have finished.
SVZ162 LAYOUT 4/7/99 6:41 PM Page 20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
