ABB 4234 601 User manual

Brand: ABB

Model: 4234 601

Type: User manual

This manual is also suitable for

4234 600

4234 600 Series

Power Supply Unit

Instruction Manual

Models 4234 600 & 4234 601

ABB LIMITED

The Company

ABB Ltd. is an established world force in the design and manufacture of instrumentation for

industrial process control, flow measurement, gas and liquid analysis and environmental

applications.

As a part of ABB, a world leader in process automation technology, we offer customers

application expertise, service and support worldwide.

We are committed to teamwork, high quality manufacturing, advanced technology and

unrivalled service and support.

The quality, accuracy and performance of the Company’s products result from over 100 years

experience, combined with a continuous program of innovative design and development to

incorporate the latest technology.

The NAMAS Calibration Laboratory No. 0255 is just one of the ten flow calibration plants

operated by the Company, and is indicative of ABB’s dedication to quality

and accuracy.

Use of Instructions

Warning.

An instruction that draws attention to the risk of injury or

death.

Caution.

An instruction that draws attention to the risk of damage to

the product, process or surroundings.

✶

Note.

Clarification of an instruction or additional information.

Information.

Further reference for more detailed information or

technical details.

Although

Warning hazards are related to personal injury, and Caution hazards are associated with equipment or property damage,

it must be understood that operation of damaged equipment could, under certain operational conditions, result in degraded

process system performance leading to personal injury or death. Therefore, comply fully with all

Warning and Caution notices.

Information in this manual is intended only to assist our customers in the efficient operation of our equipment. Use of this manual

for any other purpose is specifically prohibited and its contents are not to be reproduced in full or part without prior approval of

Marketing Communications Department, ABB Ltd.

Health and Safety

To ensure that our products are safe and without risk to health, the following points must be noted:

1. The relevant sections of these instructions must be read carefully before proceeding.

2. Warning labels on containers and packages must be observed.

3. Installation, operation, maintenance and servicing must only be carried out by suitably trained personnel and in accordance with the

information given.

4. Normal safety precautions must be taken to avoid the possibility of an accident occurring when operating in conditions of high pressure

and/or temperature.

5. Chemicals must be stored away from heat, protected from temperature extremes and powders kept dry. Normal safe handling procedures

must be used.

6. When disposing of chemicals ensure that no two chemicals are mixed.

Safety advice concerning the use of the equipment described in this manual or any relevant hazard data sheets (where applicable) may be

obtained from the Company address on the back cover, together with servicing and spares information.

BS EN ISO 9001

Cert. No. Q5907

EN 29001 (ISO 9001)

Lenno, Italy – Cert. No. 9/90A

0255

Stonehouse, U.K.

1.1 General

This instruction manual describes the installation and

operation of the 4234 600 Series Power Supply Unit (PSU),

designed to provide a stabilised (optional 500, 400, 350, 250

or 180 mA) d.c. supply for operation of a single katharometer

unit and an auxiliary 10 V d.c. supply for katharometer

temperature control.

1.2 Description – Fig. 1.1

The PSU is available in two separate versions defined in

Section 2.

The unit is housed in a metal case fitted with mounting lugs.

Cable gland entries are provided at opposite ends of the case

for supply voltage input and output cables respectively.

A printed circuit board assembly (see Fig. 1.1) contains the

circuit components. The supply voltage input is connected to

terminal block (TB1) located on the pcb, adjacent to the fuses

F2 and F3. The constant current output terminal block (TB2) is

located on the gland assembly at the opposite end of the

assembly. The auxiliary 10 V output terminal block (AUX 10V)

is located on the PCB near to TB1. The pcb is mounted on a

steel chassis and secured by six screws. The cover is

perforated to allow ventilation for cooling.

Note. The PSU has NO serviceable parts.

Two identical fuses (L & N) are mounted within the unit on the

mains input. A third fuse is connected in the d.c. line circuit of

the transformer. A fourth fuse is connected in the auxiliary

10 V d.c. line. The L & N fuses are a high breaking capacity

type and must only be replaced with identical types. See

Section 2 for rating.

1 INTRODUCTION

Fig. 1.1 Location of Internal Component

TB1

L N E

F2 F3

Warning. Hazardous Voltages

There are no servicable parts in this unit.

Please return to the manufacturer if faulty,

or seek the services of a qualified engineer.

Ensure that the mains supply is switched

off and disconnected before removing the

cover for any reason.

230 V

115 V

TB2

–

M5 Earth Stud

Cable Gland for

a.c. Mains Input

Output

Current

Links

Cable Gland for

d.c. Output to

Katharometer

Mains Input

Terminal Block

d.c. Output

Terminal Block

Fuses

∅5 to 9 mm

Cables

∅5 to

9 mm

Cable

AUX 10V

–

Cable Gland for

10 V Output to

Katharometer

CONTENTS

1 INTRODUCTION ................................................. 1

1.1 General ...................................................... 1

1.2 Description.................................................1

2 SPECIFICATION ................................................. 2

3 MECHANICAL INSTALLATION .......................... 3

4 ELECTRICAL INSTALLATION ........................... 4

4.1 Interconnection Diagrams and

Cable Requirements ..................................4

4.1.1 Katharometer Connections............4

4.1.2 Temperature Control Circuit........... 4

4.2 Accessing the PSU Terminals....................5

4.3 Electrical Connections ...............................5

5 SERVICING ......................................................... 6

5.1 Fuse Replacement.....................................6

Supply:

Model 4234600............... 230 V a.c., 50/60 Hz

Model 4234601............... 115 Va.c., 50/60 Hz

Power

Consumption

Katharometer.................. 3.5 W maximum

Katharometer with

temperature control..... 13 W maximum

Fuse Ratings:

L & N ................................ 250 mA (20 x 5 mm) 250 VA,

1500A h.b.c. cartridge type

d.c. line ............................ 400 mA (250 V a.c.)

Aux. 10 V d.c line ............ 1 A (250 V) F.B. (20 x 5 mm)

D.C. Output:...................... optional, stabilised, 500, 400,

350, 250 or 180 mA

Load: ................................. one katharometer (12.5 Ω max.)

plus interconnecting cable (2 Ω

max)

Ambient Temperature

Range:............................... –20 to +55°C

2 SPECIFICATION

Permissible Supply

Voltage Variation: ........... ±15%

Frequency Range........... 46 to 64 Hz

Output

Regulation: ....................... Within ±0.8% for

a)Load variation ±15%

b)Supply variation ±6%

c) Ambient temperature ±10°C

Ripple:............................... Less than 17.5 mV across 10 Ω

load peak to peak

Stability:............................ Within ±0.7% of initial setting

over a period of one month with

load resistance, supply voltage

and ambient temperature at

nominal stated values.

Auxiliary Output............... 10 V d.c. nominal at 1 A for

katharometer temperature

control.

Dimensions: ..................... see Fig. 3.1

Fixing: ............................... see Fig. 3.1

Weight:.............................. 2.12 kg approximately

Fig. 3.1 PSU Dimensions

Fig. 3.2 Typical Identification Labels and locations

3 MECHANICAL INSTALLATION

ABB Limited

Oldends Lane, Stonehouse,

Glos. England GL10 3TA

Code 4234/600XX

Serial No

Voltage 230 Vac

Watts

Year Manuf.

Manufactured by:

N4006

✔

The PSU must be mounted in a clean, dry, well ventilated position (on a wall or panel) in a safe area by means of the four fixing lugs.

Fig. 3.1 gives dimensions and fixing details for the unit.

Before commencing installation, check that the unit supplied is suitable for the supply voltage available – see Section 2 and the data

plate on the unit cover, Fig. 3.2.

140 CTRS

110 CTRS

170

111

120

All holes 7.0 diameter

160

20 20

3030

60 DIM

Ensure a clearance of at least 100 mm at both

ends of the unit for acces to the cable glands

and to minimise cable bends.

Mains Cable

Entry

Output to Temperature Control

Circuit in Katharometer only

Output to

Katharometer

3.0

An adaptor kit (part number 4234 519) is available for mounting the

4234 600/601 PSU in place of the 004235 000/01/02 PSU.

All dimensions are nominal

mm unless otherwise stated.

4 ELECTRICAL INSTALLATION

1–+2

C501

4 –

8 –

3 –

Power Supply Unit

4234600/601

Katharometer Types

6515

6517

6518

6520

6522

6524

7 +

mA o/p

10V o/p

For temperature controlled

katharometer block type

6518, 6520, 6524

Mains in

4234 600 – 230 V a.c.

4234 601 – 115 V a.c.

4689 Display

TBB

+12

TBB

10–

28–+29

C351

1–+2

Datum

L150

Commander Series

Fig. 4.1 Typical Interconnecting Diagram Showing 4234 600/601 PSU, Katharometer and Displays

4.1 Interconnection Diagrams and Cable

Requirements

See Fig. 4.1 for interconnections for typical gas analysis

systems.

4.1.1 Katharometer Connections

Cable connecting the constant current d.c. supply from the PSU

to the katharometer should be selected so that the maximum

cable resistance is less than 2 ohms. This limits the maximum

cable length between the katharometer and its associated PSU.

Note that the cable gland will accept a cable between 5 to 9 mm

in diameter.

4.1.2 Temperature Control Circuit

The cable connecting the auxiliary 10 V d.c. supply to the

katharometer temperature control circuit must have cable

conductance capable of passing 1 amp without undue voltage

drop or excessive heating.

Note also that the cable gland will accept a cable between 5 to

9 mm in diameter.

To gain access, remove the four

screws and lift off the cover.

Fig. 4.2 PSU Cover Removal

TB1

F2 F3

230 V

115 V

L N E

115 V a.c.

230 V a.c.

Supply

See Caution opposite

Tighten Cable Gland

M5 Earth Stud

Fig. 4.4 Connecting Outputs

Fig. 4.3 Connecting to a.c. Supply

4 ELECTRICAL INSTALLATION

To Katharometer

(see manual for

termination details)

Tighten Cable Gland

TB2

–

d.c. Output

Terminal Block

Cable Clamp

Output Current (mA) Links

500 A to X

400 B to X

350 C to X

250 D to X

180 E to X

Current Output Link

To Katharometer

temperature control

circuit

(see manual for

termination details)

AUX 10V

–

4.2 Accessing the PSU Terminals

Warning. If the PSU is cubicle mounted or has its

cover removed for test purposes, a.c. mains supply

voltage is exposed at certain locations within the

assembly when supplies are connected. Thus, there is a

risk of electrocution.

All normal precautions must be taken to avoid the risk of

accidental electrical shock during installation and

maintenance of the equipment. Ensure that the supply

cable is disconnected at its source before touching any

electrical connections.

Caution. Ensure that the correct version of the unit

has been supplied for the supply voltage available. A 115 V

unit cannot be used with a 230 V supply or vice versa.

Check that the current output meets the katharometer

input requirements (see katharometer data label) – see

Fig. 4.4. If in doubt contact ABB Limited.

Remove the power supply unit cover to obtain access to the

separate labelled terminal blocks – see Fig. 4.2.

4.3 Electrical Connections

The mains terminal block, TB1, is situated next to the transformer,

T1, and fuses, F2 and F3.

Connect the a.c. mains input cable as in Fig. 4.3.

Note. Earth bonding to be made via M5 Earth Stud.

Connect the d.c. output and 10 V cables as in Fig. 4.4.

5 SERVICING

5.1 Fuse Replacement

There are no serviceable components in these PSU's other than to replace the fuses – see Fig. 5.1. These fuses must be replaced

only with those stated in the specification. If a fault occurs the PSU should be returned to the nearest ABB Service Centre, or

returned to the factory for repair.

Fig. 5.1 Changing Fuses

TB1

L N E

F2 F3

230 V

115 V

TB2

AUX 10V

–

Switch off and disconnect

the mains supply

Remove the four screws and lift

off the cover.

Replace fuse(s)

Note. Suitable fuses may be obtained

from ABB with the following part numbers:

F1..............0231555 (400 mA cartridge)

F2 & F3....0231577 (250 mA 1500 A

hbc cartridge)

F4.............0231599 1 A (F.B.) 250 V

Replace cover, connect to mains power source

and switch on.

NOTES

…NOTES

PRODUCTS & CUSTOMER SUPPORT

Products

Automation Systems

• for the following industries:

– Chemical & Pharmaceutical

– Food & Beverage

– Manufacturing

– Metals and Minerals

– Oil, Gas & Petrochemical

– Pulp and Paper

Drives and Motors

• AC and DC Drives, AC and DC Machines, AC motors to 1kV

• Drive systems

• Force Measurement

• Servo Drives

Controllers & Recorders

• Single and Multi-loop Controllers

• Circular Chart , Strip Chart and Paperless Recorders

• Paperless Recorders

• Process Indicators

Flexible Automation

• Industrial Robots and Robot Systems

Flow Measurement

• Electromagnetic Magnetic Flowmeters

• Mass Flow Meters

• Turbine Flowmeters

• Wedge Flow Elements

Marine Systems & Turbochargers

• Electrical Systems

• Marine Equipment

• Offshore Retrofit and Referbishment

Process Analytics

• Process Gas Analysis

• Systems Integration

Transmitters

• Pressure

• Temperature

• Level

• Interface Modules

Valves, Actuators and Positioners

• Control Valves

• Actuators

• Positioners

Water, Gas & Industrial Analytics Instrumentation

• pH, conductivity, and dissolved oxygen transmitters and

sensors

• ammonia, nitrate, phosphate, silica, sodium, chloride,

fluoride, dissolved oxygen and hydrazine analyzers.

• Zirconia oxygen analyzers, katharometers, hydrogen purity

and purge-gas monitors, thermal conductivity.

Customer Support

ABB Ltd. provides a comprehensive after sales service via a

Worldwide Service Organization. Contact one of the following

offices for details on your nearest Service and Repair Centre.

United Kingdom

ABB Ltd.

Tel: +44 (0)1453 826 661

Fax: +44 (0)1453 827 856

United States of America

ABB Inc.

Tel: +1 (0) 755 883 4366

Fax: +1 (0) 755 883 4373

Client Warranty

Prior to installation, the equipment referred to in this manual

must be stored in a clean, dry environment, in accordance with

the Company's published specification. Periodic checks must be

made on the equipment's condition.

In the event of a failure under warranty, the following

documentation must be provided as substantiation:

1. A listing evidencing process operation and alarm logs at time

of failure.

2. Copies of operating and maintenance records relating to the

alleged faulty unit.

IM/4234600 Issue 1

The Company’s policy is one of continuous product

improvement and the right is reserved to modify the

information contained herein without notice.

Printed in UK (01.02)

ABB Ltd.

Oldends Lane, Stonehouse

Gloucestershire, GL10 3TA

Tel: +44 (0)1453 826 661

Fax:+44 (0)1453 827 856

ABB Inc.

2175 Lockheed Way

Carson City, NV 89706

USA

Tel: +1 (0) 775 883 4366

Fax:+1 (0) 775 883 4373

ABB has Sales & Customer Support

expertise in over 100 countries worldwide

www.abb.com

ABB 4234 601 User manual

Brand: ABB

Model: 4234 601

Type: User manual

This manual is also suitable for

4234 600

Download PDF

report

ABB 4234 601 User manual

This manual is also suitable for

ABB 4234 601 User manual

Related papers

Other documents