Infinite Peripherals LINEA PRO 5 Quick start guide

Type
Quick start guide
Linea Pro
®
5
Barcode Scanner
For iPhone
®
5/5S/SE or
iPod® Touch 5th/6th Generation
QUICK START GUIDE
Charge Your Linea Pro 5
1. Connect the mini USB cable to the USB port
on the botton of the unit.
2. Determine the battery charge status based on
the number of LEDs illuminated.
Assemble
1. Remove the top piece of the Linea Pro 5,
and then gently insert your iOS device.
2. Connect the iOS device by rmly sliding
it onto the Lightning™ connector.
3. Guide the top piece back onto the unit
until it snaps into place.
4. Press the top piece rmly onto the body
of the unit until it is secure.
Sync with iTunes®
You can sync the Linea Pro 5 with iTunes
while connected to your iOS device.
1. Enable the Pass-through sync option in
the SDK.
2. Connect the unit to a computer using
the mini USB cable.
3. After the sync is successful, refer to
the iTunes user instructions for syncing
with your iOS device.
To disable sync mode:
Exit iTunes, and then unplug the unit
from the mini USB cable.
LED Battery Status
Press the battery status button to view the LEDs.
When the unit is fully discharged and enters Tamper Detect
mode, it can only be reactivated by Innite Peripherals.
Pass-through charging is supported for your iOS device. An
iPod and Linea Pro 5 combination may be charged using a
USB cable to a computer, USB to AC adapter, or by a station
charger.
Note:
Due to requirements, the unit and iPhone combination cannot be
charged with a USB cable to computer.
6
5
1
3
2
4
Front of Linea Pro 5:
1. iOS device On/Off button
2. Linea Pro 5 Scan/On button
3. Scan engine
4. Volume buttons
5. USB sync/charge port
Back of Linea Pro 5:
1. iOS device On/Off button
2. Linea Pro 5 Scan/On button
3. Scan engine
4. Magnetic strip reader (MSR)
3
1
2
4
100-76 Solid green (4 LEDs)
75-51 Blink green (3 LEDs)
50-26 Blink green (2 LEDs)
25-1 Blink green (1 LED)
Emergency low battery
Status %
Description
Troubleshooting
iOS device is not syning to iTunes.
Linea Pro 5 is not congured to sync
When swiping a card no data is returned.
Card is inserted incorrectly
Swipe method is incorrect
Faulty read head
Unreadable magnetic stripe
Scanner does not turn on.
Unit battery is too low
Unit is not activated by the software
Faulty scan engine
Unable to multi-scan.
Multi-scan is not enabled or supported by the software
RFID does not turn on.
Unit battery is too low
Unit is not powered on
Faulty RFID reader
Product Returns
Use the link in step 1 to create an account and gain access to our Knowledge
Base and online support services. Through our online support center, you’ll be
able to download les, open a Support Ticket, manage your RMAs, view your
account Prole and subscribe to Alerts.
To request a RMA
1. Create a user account in the RMA Support Portal at http://ipcmobile.
com/support/rma/
2. Login to your user account and then click Create RMA Request.
3. Read the instructions provided and complete the online request form.
4. Note the assigned RMA number and write it clearly on your shipping
carton.
5. Ship your equipment to us using the address provided.
Warnings & Cautions
Please observe the following precautions:
Keep the unit away from liquids. Do not immerse it in water.
The unit is intended for Indoor use only. When not in use, place it in a
cool, dry place.
Do not place the unit near a heat source. Keep both the power supply
and unit away from direct sunlight and/ or heat.
Unit should only be repaired by Innite Peripherals.
Warranty
Innite Peripherals does not warrant, and is not responsible for, any damage
to the Linea Pro 5 (“Product”) as a result of liquid or solid particle intrusion
into the Product or damage caused by dropping the Product. If a material or
workmanship defect arises with regard to any Innite Peripherals product,
and a valid claim is received within the Warranty Period, Innite Peripherals
(at Innite Peripherals’ sole discretion) will (1) repair the Product using new
or refurbished parts, or (2) replace the Product with a new or refurbished
Product. For purposes of this limited warranty, “refurbished” means a product
or part that has been substantially returned to its original specications. In
the event of a defect, these are your exclusive remedies.
Note:
Box contents and part numbers may vary based on your order conguration.
Quick Start Guide | Linea Pro 5
Accessories & Additional Information
For current or future offerings and additional product documentation, visit
our website at https://ipcmobile.com/devices/linea-pro-5 or contact your
Innite Peripherals account representative for complete details.
Note:
The iOS device and any other additional items shown may not be included in
your order.
Software Devlopers Kit (SDK)
Integrating the Linea Pro 5 with your iOS application requires the Innite
Peripherals mobile device SDK. For the latest Innite Peripherals mobile
device SDK, please visit our developer portal:
https://developer.ipcmobile.com
Contact Information
Mobility Sales/ Technical Support Center
Innite Peripherals, Inc.
17681 Mitchell N
Irvine, CA 92614
Toll-Free: (866) 278-7860
Ofce: (949) 222-0300
Website: ipcmobile.com
Headquarters/ Main Warehouse
Innite Peripherals, Inc.
2312 Touhy Avenue
Elk Grove Village, IL 60007
Toll-Free: (800) 278-7860
Ofce: (847) 818-1260
Fax: (847) 818-1287
Specications subject to change without notice. Innite Peripherals, Mobilize Your Enterprise, Linea Pro, Innea Tab and
Innea Omni are trademarks of Innite Peripherals, Inc. All other trademarks are the property of their respective owners.
QSG-10064 Rev B
  • Page 1 1
  • Page 2 2

Infinite Peripherals LINEA PRO 5 Quick start guide

Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI