Infinite Peripherals LINEA PRO 6 Quick start guide

Brand
Infinite Peripherals
Model
LINEA PRO 6
Type
Quick start guide
ABOUT YOUR LINEA PRO 6
CHARGING STATION (5-Unit)
ASSEMBLY
LINEA PRO
®
6
Charging Station
(5-Unit)
QUICK START GUIDE
CHARGE STATUS TROUBLESHOOTING
Charging Bay
Cooling Vent
Charging Contacts
Attachment
LED Indicator
Linea Pro 6 Charging Station (5-Unit) with Standard Case
Linea Pro 6 Charging Station (5-Unit) with Rugged Case
1. Place the Linea Pro 6 Charging Station
on a sturdy, clean and dry surface in an
open, well-ventilated area away from
direct sunlight.
2. Insert the included AC adapter plug into
the DC Jack Port on the charger.
Connect the AC power adapter to a
power outlet.
3. Insert the unit into a charging bay,
ensuring the battery contacts are
aligned with the bay’s contacts. The LED
lights up with the charging status.
The Linea Pro 6 Charging Station (5-Unit) uses
a tricolor LED to indicate the charge status.
Check the status LED on each slot to verify
normal charging status. When the battery is
fully charged, the LED indicator is green.
Status Indicator LEDS
Green Inserted device is fully charged.
Orange Inserted device is charging.
Flashing Red Over-current protection is enabled.
Charging bay is at or above
maximum current fault (1.9A) and
has stopped working.
Solid Red Over-current protection is enabled
due to overheat fault (over
60°C/140°F).
No LED Indicates there is no device in
charging bay or there is no power
supply attached the charger.
Notes:
When the LED is solid red and the operating
temperature decreases to at or below 55°C/131°F, the
charging bay begins working again.
When you do not see the LED, over current
protection may be enabled, if the charging pins are
shorted, or there is no load.
The LED does not come on when a unit is
inserted.
• Ensure that the power supply is fully
plugged into the outlet and plugged
into the DC port.
It takes an excessive amount of time to fully
charge the battery.
• Verify ambient temperature meets the
operating temperature requirements.
Operating: 0°C – 40°C (32°F – 104°F)
Please visit our website at
ipcmobile.com, or contact your Infinite
Peripherals account representative, for
additional information about current and
future product accessory oerings.
ACCESSORIES
Mobility Sales/Technical Center
Innite Peripherals, Inc.
17681 Mitchell N.
Irvine, CA 92614
Toll-Free: (866) 278-7860
Oce: (949) 222-0300
Headquarters/Main Warehouse
Innite Peripherals, Inc.
2312 Touhy
Elk Grove Village, IL 60004
Toll-Free: (800) 278-7860
Oce: (847) 818-1260
Fax: (847) 818-1287
Technical Support
Innite Peripherals, Inc.
17681 Mitchell N.
Irvine, CA 92614
Toll-Free: (866) 278-7860
Oce: (949) 222-0300
Email
[email protected]
Website
ipcmobile
.com
•
Note: Box contents and part numbers may vary
based on order configuration.
Infinite Peripherals does not warrant, and
is not responsible for, any damage to the
Linea Pro 6 Charging Station (“Product”) as a
result of liquid or solid particle intrusion into
the Product or damage caused by dropping
the Product. If a material or workmanship
defect arises with regard to any Infinite
Peripherals product, and a valid claim is
received within the Warranty Period, Infinite
Peripherals (at its sole discretion) will (1)
repair the Product using new or refurbished
parts or (2) replace the Product with a new
or refurbished Product. For purposes of
this limited warranty, “refurbished” means a
product or part that has been substantially
returned to its original specifications. In the
event of a defect, these are your exclusive
remedies.
QSG-10019 Rev. B
WARNINGS & CAUTIONS
Please observe the following precautions:
• Do not immerse the charger in water.
• When not in use, store the charger in a
cool dry place.
• Do not store or operate the charger near a
heat source.
• Do not directly connect the charger to an
electrical outlet.
• The charger is information technology
equipment and for oce use only, and
should only be used for its intended
purpose.
• The output power drawn from the supply
must not exceed the rating for this
product.
• The power to the device should be
removed by unplugging the AC main
plug.
• Do not use any other AC adapter other
than the adapter supplied with this
charger. Use of any other adapter may
damage the charger and will void the
warranty.
ADDITIONAL INFORMATION
Please contact your Infinite Peripherals sales
representative for technical specifications and
additional product documentation.
WARRANTY
Specications subject to change without notice. Innite
Peripherals, Mobilize Your Enterprise, Linea Pro, Innea, Innea
Tab and Innea Omni are trademarks of Innite Peripherals, Inc.
All other trademarks are the property of their respective owners.
PRODUCT RETURNS
Use the link provided to create an account and gain access to our Knowledge Base and online support
services. Through our online support center, you’ll be able to download les, open a Support Ticket, manage
your RMAs, view your account Prole and subscribe to Alerts.
To request a RMA:
1. Create a user account in the RMA Support Portal at https://ipcmobile.com/support/rma.
2. Login to your user account and click the Create RMA Request option.
3. Read the instructions provided and complete the online request form.
4. Note the assigned RMA number and write it clearly on your shipping carton.
5. Ship your equipment back to us at the address provided.
  • Page 1 1
  • Page 2 2

Infinite Peripherals LINEA PRO 6 Quick start guide

Brand
Infinite Peripherals
Model
LINEA PRO 6
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents