SECO-LARM EAP-5D5Q User manual

Brand: SECO-LARM

Model: EAP-5D5Q

Type: User manual

This manual is also suitable for

EAP-3D5Q, EAP-5D5Q

Access Control Power Supply, Five Outputs

Manual

Features:

•

Input 110~240 VAC, fused at 3.15A

• 5 Outputs individually fused (PTC, 1.1A), in

both fail-safe and fail-secure modes

• DC Output failure supervision relay

• Filtered and electronically regulated outputs

• Individual LED status indicators for AC input,

DC output, and channel outputs

• Adjustable output voltage to compensate for

voltage drop

•

AC Power failure supervision relay

• Over-current fuse-protected AC input

• 12/24 VDC Outputs, field selectable

• Battery failure / low battery supervision relay

• Built-in back-up battery charger (Batteries not

included)

•

Automatically switch to backup battery if AC fails.

• Selectable 2.2kΩ End-of-Line (EOL) resistor for AC

failure and battery failure supervision relays via DIP

switch

• Auxiliary output relay

• Selectable delay timer (5sec, 5min, 5h) for AC failure

supervision relay via DIP switch

• Board designed with LED overload indicator and

automatic shutdown for short-circuit protection.

• Heavy-duty steel case with removable cover for easy

access to connections

• Ventilation holes to prevent heat buildup

• Room for two 7Ah batteries (or two 12Ah batteries for

EAP-5D5Q) (Batteries not included)

• Knockouts for power connections and optional cam lock

EAP-5D5Q shown

ENFORCER Access Control Power Supply, Five Outputs

2 SECO-LARM U.S.A., Inc.

1 2

Power Supply / Enclos

Screws for the enclosure door

Cable management clamp

Cable management nut

Wires for backup battery

6ft Power cord with

ground wire

Manual

(red, black, white)

Protective plastic bushing for power cable

Model EAP-3D5Q EAP-5D5Q

Operating voltage 110~240 VAC

Output voltage 12/24 VDC (selectable)

Output voltage range

(adjustable)

12VDC 12~13

24VDC 23~25

LED Status indicator

DC Red=12VDC, blue=24VDC for each output

AC Green, input

Current rating 3A@12VDC, 1.5A@24VDC 5A@12VDC, 2.5A@24VDC

Supervision relays EOL: Selectable ON (2.2kΩ) or OFF, 3A@24VDC dry relay output

Power failure supervision relay 3A@24VDC

Auxiliary supervision relay 3A@24VDC

AC Input fuse rating 3.15A

AC Power cord 6ft (1.8m)

Operating humidity 85% maximum

Operating temperature -4°~149° F (-20°~65° C)

Dimensions 12

"x12

"x3

" (308x311x90 mm) 14

"x14

"x4

" (377x363x105 mm)

Weight 10-lb 2-oz (4.6kg) 11-lb (5kg)

Specifications:

Overview:

Parts List:

Backup battery

terminal

AC Input LED

status indicator

AC Failure

supervision

relay output

Battery presence / low

battery monitor DIP

switch (default ON)

12/24 VDC

Output selection

slide switch

(default 12VDC)

DC Output voltage

adjustment

potentiometer

–

AC Failure delay

timer DIP switch

(default 5s)

Battery failure / low

battery supervision

relay output

110~240

VAC Input

terminals

End

line (EOL)

2.2kΩ resistor DIP

switch (default ON)

Power

switch

1 2

Vol. Out.

OFF

24V

12V

1 2

LB Mode

Both

Bpth

OFF

PRESENT

FAIL

AC FAIL Time

OFF

DC Output LED

status indicator*

red=12V, blue=24V

OFF

2.2K

12/24 VDC

fail-safe and

fail-secure

fused outputs

DC power fail

supervision

relay

Auxiliary

output relay

DC voltage

input

from access

control station or

emergency switch

N.O. or N.C. input

from access

control station or

emergency switch

Installation:

EAP-5D5Q shown

Built

in output overload

/ short

circuit

protection

–

If an overload occurs, the motherboard's

output

voltage output will drop. The

voltage drop will depend on the extent of the overload. The greater the overload the greater the voltage drop. If the overload is

extensive, the voltage output will become intermittent and the red LED will start flashing. When the overload is removed, the

motherboard will automatically restart normal output. If an output short-circuit occurs, the motherboard will automatically shut the

output down and the red LED will turn off. When the short-circuit is removed, the motherboard will automatically come back on line.

IMPORTANT:

The ENFORCER Power Supply is not waterproof or weatherproof. Therefore, it must be mounted indoors where it

will not be exposed to rain or other moisture.

Installation must be done by qualified personnel, and should conform to local and all other applicable codes.

1. Choose a mounting location out of sight and protected from moisture and weather, but easily accessible for future servicing.

NOTE: Make sure the space where the enclosure is to be mounted has adequate ventilation. Otherwise, heat buildup inside

the

enclosure could damage the electronic parts.

2. Locate the enclosure mounting holes. Using these holes as a template, mark the location of the 4 screws on the wall with a

pencil.

3. Thread the AC power cord through the protective plastic power cord bushing and then through the power cord hole in the

enclosure, snapping the bushing into place. Secure the power cord with the cable management clamp.

ENFORCER Access Control Power Supply, Five Outputs

SECO-LARM U.S.A., Inc. 3

Installation

(Continued)

Attach to the wall by first screwing in two

" x 1" (4x26 mm) upper screws

using plastic wall anchors if needed (both not included) until the gap between

the wall and the screw head is approximately

" (6mm).

5. Hang the enclosure on the two upper screws using the enclosure's upper

screw holes and adjust the proper location of the enclosure. Screw in the two

lower screws. Then securely fasten the upper and lower screws.

6. Run wires from the access control devices to the power supply. The

enclosure has knock-outs on the side, top, bottom, and rear panels for

running cables. Punch out the appropriate knock-outs.

7. Set the desired DC output voltage (12 or 24 VDC) of the power supply using

the sliding switch (see "Overview," pg. 3). The default is 12VDC.

8. Connect the backup battery to the backup battery terminal (see Fig. 1).

Check voltage output reading of the power distribution module (PDM). If the

green LED is ON, and the voltage reading of the PDM's five channel outputs

are the same as the backup battery terminal's voltage reading, this indicates

that the power supply is working properly. Disconnect battery after testing.

9. Connect the power input wires of the access control devices or accessories

to the power distribution module (PDM, see "Overview," pg. 2). Observe

correct polarity. For fail-secure devices, connect positive to terminals

marked "POS. OPEN LOOP" and negative to terminals marked "NEG." For

fail-safe devices, connect positive to terminals marked "POS. CLOSE LOOP"

and negative to terminals marked "NEG".

IMPORTANT NOTES/WARNINGS:

a. To avoid risk of electrical shock, the ground terminal of the "AC

INPUT" MUST be connected to earth via the power cord.

b. If the "Trigger" terminal block function is to be used, a 2.2kΩ resistor

must always be connected to the "Trigger" terminal block as in Fig. 2.

c. Maximum total current connected to the power supply terminal must not

exceed the power supply's total current capacity (5A@12VDC and

2.5A@24VDC).

d. Check the output voltage reading of the power supply as stated above

and double check the specified operating voltage of each device before

connecting it to the power supply to avoid potential damage.

e. Use at least 18-gauge wires to minimize voltage drop. The thinner the

wire, the greater the voltage drop.

f. Keep power limited wiring separated from non-power limited wiring (AC

input, battery wiring) by a minimum distance of

" (7mm) and use

separate knockouts in the enclosure.

10. Connect a visual or audio indicator (such as siren or strobe light) to the AC-

failure and battery-failure / low battery supervision relays if needed (see

"Overview, pg. 2). Use between 22AWG to 18AWG wire size.

11. Follow the connection diagrams shown in Fig. 3~8 to trigger the PDM from a

wet and/or dry contact switch from the control station.

12. Connect a visual or audio indicator (such as siren or strobe light) to the

power fail supervision relay and Auxiliary output relay if needed.

13. Double check to ensure everything is connected properly. Connect the AC

power (110~240 VAC). The AC LED & DC LED on the main board

(red=12VDC, blue+24VDC), and the power LED on the PDM should turn ON

to indicate the power supply unit is working properly.

14. Reconnect the backup battery. Again ensure the voltage output reading of

the PDM is within the normal working range. Check the DC output voltage

reading at the end of the wire pairs where it is to be connected to the device.

If the output voltage reading falls below the minimum voltage requirement of

the device, use a small screwdriver to carefully turn the potentiometer

marked "VR1" located on the PCB. Turn clockwise to increase the voltage

and counterclockwise to decrease the voltage (see "Overview," pg. 2).

Fig. 1

12VDC

24VDC

–

12VDC

Battery

–

12VDC

Battery

–

12VDC

Battery

2kΩ (EOL)

resistor

Fig. 2

Fig. 3

DC input from

control station

2kΩ (EOL)

resistor

N.C.

switch

Momentary trigger for wet and/or

dry N.C. switch

Fig. 4

2kΩ (EOL) resistor

N.O.

switch

DC input from

control station

Momentary trigger for wet

and/or

dry N.O. switch

Fig. 5

Latch trigger for wet and/or dry

N.C. switch

N.O. switch for

RESET

N.C. switch from

control panel

2kΩ

(EOL)

resistor

Fig. 6

Latch trigger for wet and/or dry

N.O. switch

N.C. switch for

RESET

N.O. switch

from control

panel

2kΩ (EOL)

resistor

ENFORCER Access Control Power Supply, Five Outputs

4 SECO-LARM U.S.A., Inc.

Installation (Continued)

IMPORTANT NOTE

a. Do not adjust the potentiometer unless absolutely necessary. Adjusting the potentiometer alters default factory settings.

b. The potentiometer adjusts the voltage of all output wire pairs. Check each device carefully. An output voltage in excess of

the specified voltage level of the device may cause damage.

15. Once the desired DC output voltage is achieved, connect the wire pairs to the device.

Programmable Features

a. AC-failure Relay Output Delay Timer — Program the AC-failure relay delay timer at 5sec, 5min or 5h using the DIP switch

(see "Overview," pg. 2). The default setting is at 5sec.

b. 2.2kΩ End-of-Line (EOL) Resistor — The end-of-line 2.2kΩ resistor for AC-failure relay and battery-failure / low battery

supervision relays (3A@24VDC) can be activated independently using the DIP switch (see "Overview," pg. 2, default ON).

c. Battery Presence and Low Battery Monitor —

When the LB MODE DIP switches are in the ON position, the power supply will

monitor the battery to verify if it has sufficient voltage to run the power supply in case of AC power failure. Selecting "OFF"

will stop monitoring of battery status and will charge battery continuously. It can take up to 5 minutes to alert you of a battery

failure. The length of time the system will run will be limited by the overall capacity and the age of the batteries and the

amount of load being drawn off the power supply.

16. Connect the backup battery to the backup battery terminal (see Fig. 2 and "Overview," pg. 2, default ON).

17. Close the enclosure door and secure it with either the provided machine screws or an optional cam lock.

SECO-LARM

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

larm.com

Phone:

(949) 261

2999 | (800) 662

0800

Email: sales@seco

larm.com

PITSW1

Order Part# 764

034

MI_EAP

xD5QUS_210303.docx

NOTICE:

The SECO

LARM policy is one of continual development and improvement. For that reason, SECO

LARM reserves the right to change

specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A.,

Inc. or their

WARRANTY:

This SECO

LARM product is warranted against defects in material and workmanship while used in normal service for

one

(

)

year from

the date of sale to the original customer. SECO-LARM’s obligation is limited

to the repair or replacement of any defective part if the unit is returned,

transportation prepaid, to SECO-

LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse,

neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-

LARM determines that such equipment is

not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and

the purchaser’s

exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-

LARM be liable for any special,

collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

Fig. 7

Multiple PDM momentary trigger for wet and/or

dry N.O. switch

dditional

PDM if needed

2kΩ

(EOL)

resistor

2kΩ (EOL)

resistor

VDC input from

control station

N.O.

switch

Fig. 8

Multiple PDM momentary trigger for wet and/or

dry N.O. switch

dditional

PDM if needed

2kΩ

(EOL)

resistor

2kΩ (EOL)

resistor

VDC input from

control station

N.C.

switch

Table 1: Terminal Functions

Main Board Power Distribution Module (PDM)

Legend Functions Legend Functions

A E N To connect 110~240 VAC power ("A" for active

wire, "E" for earth or ground wire, and "N" for

neutral wire

TRIGGER Used to connect NO or NC input trigger signal (2.2kΩ EOL resistor)

from access control panel. A short or open circuit will transfer

power from "POS CLOSE LOOP" to "POS OPEN LOOP."

BAT.

FAIL

Used to notify battery failure. Dry contact relay

rated at 3A@24VDC. If backup battery is not

connected properly or if voltage output falls

below 11.2VDC for 12VDC setting (or 22.7VDC

for 24VDC setting, the connected warning device

will be activated.

VOL.

TRIGGER

Used to connect wet (5~30 VDC) input trigger signal from access

control panel. A short circuit or open circuit will transfer power from

"POS CLOSE LOOP" to "POS OPEN LOOP."

POWER FAIL Used to notify loss of DC power. Driy contact relay rated

3A@24VDC. If VDC input to the PDM is interrupted, the connected

warning device will be activated.

– BAT +

Used to charge the backup battery. Maximum

charging current is 5A

AUX OUTPUT

Used to activate other auxiliary device when trigger signal is

received from the "TRIGGER" or "VOL TRIGGER" terminals

– DC + 12 or 24 VDC Output terminal from main board – DC INPUT +

12 or 24 VDC Input from main board

California Proposition 65 Warning

These products may contain chemicals which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

SECO-LARM EAP-5D5Q User manual

Brand: SECO-LARM

Model: EAP-5D5Q

Type: User manual

This manual is also suitable for

Download PDF

report

SECO-LARM EAP-5D5Q User manual

This manual is also suitable for

SECO-LARM EAP-5D5Q User manual

Related papers

Other documents