EDWARDS CBR & WBR Installation guide

EDWARDS
Brand
EDWARDS
Model
CBR & WBR
Category
Mounting kits
Type
Installation guide
PP46000-1268 ISSUE 3 © 2001
CHESHIRE, CT 203-699-3300 FAX 203-699-3365 (CUST. SERV.) 203-699-3078 (TECH. SERV.)
OWEN SOUND, CANADA 519-376-2430 FAX 519-376-7258
Installation Instructions for AdaptaBeacon
®
Catalog No. WBR Wall
Mount Bracket and Catalog No. CBR Corner Mount Bracket
Description
The Edwards Wall Bracket and Corner Bracket are designed for
use with Edwards AdaptaBeacon visual signals having a base suit-
able for 1/2" (13 mm) or 3/4" (19 mm) conduit mounting.
The CBR Corner Mount Bracket may be used only with surface
installed conduit/wiring (see Figure 1). The WBR Wall Mount
Bracket may be used with surface installed conduit/wiring (see
Figure 2) or with concealed conduit/wiring (see Figure 3).
Installation
The brackets must be installed in acordance with the National
Electrical Code (NEC), Canadian Electrical Code (CEC), local
code, and the local authority having jurisdiction, and using ap-
proved connection means.
Corner Mount (Figure 1)
1. Use the corner section of the bracket as a template to mark the
positions of the four mounting screws on the mounting surface.
2. Drill the four mounting holes at the positions described in 1
(above). Drill size should be determined by the size of the
mounting anchors and mounting screws (not supplied)
selected.
3. Remove the 1/2" (13 mm) knockout from the bottom of the
bracket. For indoor applications, install a 1/2" (13 mm) set
screw connector and locknut as shown in Detail A. For outdoor
applications, use appropriate conduit hardware. A pull box
may be used to simplify installation.
4. Referring to instructions supplied with the AdaptaBeacon,
assemble bracket and secure AdaptaBeacon, routing field
ground and power wiring and making ground and power
wiring connections appropriately.
The external threaded nipple protruding from the bracket arm
is for securing the AdaptaBeacon. A ground terminal is
provided for securing ground to the bracket in back of the
bracket arm. Two 1/4-20 x 1 1/4" (32 mm) screws are provided
to mount bracket arm to the corner section.
NOTE: If the Edwards AdaptaBeacon includes a 3/4" (19 mm)
NPT conduit entrance, assemble the 3/4" - 1/2" (19 - 13
mm) reducing bushing to the external threaded nipple
protruding from the bracket.
WARNING
Do not make power connections within the bracket.
5. Turn on the power to verify that the signal operates properly.
Wall Corner
Corner
Bracket
Assembly
Mounting
Screws
See Detail A
1/2" Conduit and
Connectors (by others)
Pull Box (by others
if required)
Make Connections
in Base of
AdaptaBeacon
Gasket
Figure 1. Corner Mount Bracket Surface Wiring
Conduit
Set Screw Conduit
Connector
Bracket
Locknut
Detail A (Indoor Mounting Only)
Wall Mount - Surface Conduit/Wiring (Figure 2)
1. Use the backplate as a template to mark the positions of the
four mounting screws on the mounting surface.
2. Drill the four mounting holes at the positions described in 1
(above). Drill size should be determined by the size of the
mounting anchors and mounting screws (not supplied)
selected. Use oval head screws for mounting.
3. Remove the 1/2" (13 mm) knockout in the bottom of the
bracket. For indoor applications, install a 1/2" (13 mm) set
screw connector and locknut as shown in Detail A of Figure 1.
For outdoor applications, use appropriate conduit hardware.
A pull box may be used to simplify installation.
WARNING
Do not make power connections within the bracket.
4. Referring to instructions supplied with the AdaptaBeacon,
assemble bracket and secure AdaptaBeacon, routing field
ground and power wiring and making ground and power
wiring connections appropriately.
The external nipple protruding from the bracket arm is for
securing the AdaptaBeacon. A ground terminal is provided
for securing ground to the bracket in back of the bracket arm.
Two 1/4-20 x 1 1/4" (32 mm) screws are provided to mount
bracket arm to the backplate.
NOTE: If the Edwards AdaptaBeacon includes a 3/4" (19mm)
NPT conduit entrance, assemble the 3/4" - 1/2" (19-13
mm) reducing bushing to the external threaded nipple
protruding from the bracket arm.
5. Turn on the power to verify that the signal operates properly.
Wall Mount - Concealed Conduit/Wiring (Figure 3)
1. Mount the backplate to the installed standard 4" (102 mm)
square or 4" (102 mm) octagonal electrical outlet box with
oval head screws.
2. Mount the bracket to the backplate with the two 1/4-20 x 1 1/
4" (32 mm) screws provided.
3. Referring to instructions supplied with the AdaptaBeacon,
assemble bracket and secure AdaptaBeacon, routing field
ground and power wiring and making ground and power
wiring connections appropriately.
The external threaded nipple protruding from the bracket arm
is for securing the AdaptaBeacon. A ground terminal is
provided for securing ground to the bracket in back of the
bracket arm. Two 1/4-20 x 1 1/4" (32 mm) screws are provided
to mount bracket arm to the backplate.
NOTE: If the Edwards AdaptaBeacon includes a 3/4" (19 mm)
NPT conduit entrance, assemble the 3/4" - 1/2" (19 mm
- 13 mm) reducing bushing to the external threaded
nipple protruding from the bracket arm.
WARNING
Do not make power connections within the bracket.
Backplate
Mounting
Screws
See Detail A
1/2" Conduit and
Connectors (by others)
Pull Box (by others
if required)
Make Connections
in Base of
AdaptaBeacon
Gasket
Figure 2. Wall Mount Bracket Surface Wiring
Backplate
Mounting
Screws
Make Connections
in Base of
AdaptaBeacon
Gasket
Wallbox and Screws
(by others)
Wall Bracket
Assembly
Figure 3. Wall Mount Bracket Concealed Wiring
PP46000-1268 ISSUE 3
4. Turn on the power to verify that the signal operates properly.
  • Page 1 1
  • Page 2 2

EDWARDS CBR & WBR Installation guide

EDWARDS
Brand
EDWARDS
Model
CBR & WBR
Category
Mounting kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents