ELK ELK-M1KCWB Operating instructions

ELK
Brand
ELK
Model
ELK-M1KCWB
Type
Operating instructions

ELK ELK-M1KCWB is a two-piece, surface mount metal wall box. It features 1/2” and 3/4” electrical conduit knockouts, along with various mounting holes on the front that permit mounting of either a ELK-M1KP or ELK-M1KP2 Keypad backplate.

This device is ideal for commercial jobs, schools, businesses, factories, or any situation where a Keypad needs to be surface mounted with no ability to run or conceal the wiring within the structure’s walls.

The ELK ELK-M1KCWB is easy to install. Simply separate the metal backplate from the front cover, place the backplate against the wall, mark the location of the four mounting holes, predrill the wall surface, and secure the backplate using screws and/or plastic anchors.

ELK ELK-M1KCWB is a two-piece, surface mount metal wall box. It features 1/2” and 3/4” electrical conduit knockouts, along with various mounting holes on the front that permit mounting of either a ELK-M1KP or ELK-M1KP2 Keypad backplate.

This device is ideal for commercial jobs, schools, businesses, factories, or any situation where a Keypad needs to be surface mounted with no ability to run or conceal the wiring within the structure’s walls.

The ELK ELK-M1KCWB is easy to install. Simply separate the metal backplate from the front cover, place the backplate against the wall, mark the location of the four mounting holes, predrill the wall surface, and secure the backplate using screws and/or plastic anchors.

Keypad Conduit Wall Box ELK-M1KCWB
The M1KCWB is a two-piece, surface mount metal wall box. It features 1/2” and 3/4” electrical conduit knockouts,
along with various mounting holes on the front that permit mounting of either a ELK-M1KP or ELK-M1KP2 Keypad
backplate. Applications include: commercial jobs, schools, businesses, factories, etc., or virtually any situation where
a Keypad needs to be surface mounted with no ability to run or conceal the wiring within the structure’s walls.
PO Box 100 • Hildebran, NC 28637 • 800-797-9355 • 828-397-4200
Fax 828-397-4415 • www.elkproducts.com • info@elkproducts.com
ELK
PRODUCTS, INC.
02/10
FRONT VIEW
Shown with front plate
installed over
backplate.
CUT AWAY VIEW
Front Plate installed over backplate and secured with
two # 6-32" x 1.375" flat head machine screws.
INSTALLATION PROCEDURES:
1. Separate the metal backplate from the front cover.
2. Place the backplate against the wall making certain it is level. Mark the location of the 4 mounting holes. For the M1KP
Keypad the long side should be horizontal and for the M1KP2 Keypad the long side should be vertical.
3. Predrill the wall surface and secure the backplate using screws and/or plastic anchors (screws and anchors not supplied).
4. Orient the front cover upright so that the holes match up with the necessary mounting holes on the Keypad backplate.
Choose and remove the necessary conduit knockout. Secure a conduit adapter fitting in the knockout hole.
5. Slip the front cover over the backplate and secure with the supplied 6-32 x 1.375 type "f" flat head machine screws.
6. Secure the keypad backplate onto the KCWB using at least 4 screws. (Keypad mounting screws not supplied)
7. Connect the conduit, then complete the wiring and installation of the Keypad.
Metal Backplate
Mount vertical for ELK-M1KP2
Keypads
Metal Backplate
Mount horizontal for ELK-M1KP Keypads
Mounting holes
(4 per)
Note: Orient two (2) most distant
holes on top for the M1KP Keypad.
  • Page 1 1

ELK ELK-M1KCWB Operating instructions

ELK
Brand
ELK
Model
ELK-M1KCWB
Type
Operating instructions

ELK ELK-M1KCWB is a two-piece, surface mount metal wall box. It features 1/2” and 3/4” electrical conduit knockouts, along with various mounting holes on the front that permit mounting of either a ELK-M1KP or ELK-M1KP2 Keypad backplate.

This device is ideal for commercial jobs, schools, businesses, factories, or any situation where a Keypad needs to be surface mounted with no ability to run or conceal the wiring within the structure’s walls.

The ELK ELK-M1KCWB is easy to install. Simply separate the metal backplate from the front cover, place the backplate against the wall, mark the location of the four mounting holes, predrill the wall surface, and secure the backplate using screws and/or plastic anchors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents