Pittsburgh 60392 Owner's manual

Category
Power tools
Type
Owner's manual

This manual is also suitable for

Page 2 For technical questions, please call 1-800-444-3353. Item 60392
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
1. Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
2. Keep children and visitors away while installing.
Distractions can cause you to lose control.
3. Store idle products out of reach of children and
other untrained persons. Never allow children
to play with or around the Wheel Chock.
4. Stay alert. Watch what you are doing, and
use common sense when using the Wheel
Chock. Do not use this product while tired
or under the inuence of drugs, alcohol, or
medication. A moment of inattention while
operating may result in serious personal injury.
5. Dress properly. Do not wear loose clothing
or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
6. Do not overreach. Keep proper footing
and balance at all times. Proper footing
and balance enables better control of the
motorcycle in unexpected situations.
7. Use safety equipment. Always wear eye
protection. Dust mask, nonskid safety shoes,
hard hat, heavy-duty work gloves, or hearing
protection must be used for appropriate conditions.
Always wear ANSI-approved safety goggles
and a dust mask/respirator when installing
or performing maintenance on this tool.
8. Maintain labels and nameplates on the
tool. These carry important information. If
unreadable or missing, contact Harbor
Freight Tools for a replacement.
9. Use the correct product for your motorcycle.
Make sure the motorcycle’s wheel ts into
the Wheel Chock prior to rst use.
10. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Specications
Construction Formed Steel w/ Carbon Steel Hardware & Thermoplastic End Caps
Overall Dimensions 24-1/2" L X 9-3/4" W X 12-7/8" H
Weight 16 Pounds
Moveable Chock Length 10"
Page 3For technical questions, please call 1-800-444-3353.Item 60392
Setup and Use
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the
parts listed in the following pages, refer to the
Assembly Diagram at the end of the manual.
The Wheel Chock comes fully assembled, however
it must be mounted onto a solid surface to secure it.
It is designed to be mounted on the bed of a truck,
or a motorcycle lift, or onto a concrete oor.
Concrete Floor Mounting
1. Choose a location to install the Wheel Chock that
is at, level, and capable of bearing the combined
weight of the Wheel Chock and the motorcycle
being secured. Be certain that the location
will not obstruct walkways and will still provide
enough room to retrieve the motorcycle after it is
mounted. The surface of the location should be
one suitable for the mounting of heavy equipment.
2. Use the mounting holes in the Base (7)
of the Wheel Chock as a template.
3. Arrange the Base (7) in the chosen location and,
using a pencil, mark where the holes are to be
drilled. You will need concrete anchors (not included)
to secure the Base (7) to the concrete oor.
4. Using the correct size concrete drill bit (not included),
drill the mounting holes to secure the Base (7).
5. Attach the concrete anchors to the oor.
6. Secure the Base (7) to the oor
utilizing the concrete anchors.
Truck Bed or Motorcycle Lift Mounting
1. Place the Base (7) in the desired location of the
truck bed or motorcycle lift where you want to mount
it. Use the Base (7) as a pattern to mark where
you will drill the holes that accept the hardware
to mount the Wheel Chock. Use a power drill (not
included) and a steel cutting drill bit (not included)
to drill holes in the truck bed or motorcycle lift.
Warning: Before drilling, verify that the installation
surface has no hidden wires, brake lines, etc.
2. Attach the Base (7) to the truck bed utilizing the
Mounting Bolts (6), Nylon Sleeves (8), Large
Washers (9), Spring Washers (3), and secure
with Hex Nuts (10). See Assembly Diagram.
Operating Instructions
1. Select the correct mounting hole for the motorcycle
being loaded into the Wheel Chock, and use the
Pivot Bolts (5) to secure the Pivoting Bracket in place.
Note: Do not sit on the motorcycle when
it is loaded in the Wheel Chock.
2. To load a motorcycle, lower the Pivoting Bracket
(13) to the horizontal position and simply push
the motorcycle into the Wheel Chock.
Maintenance and Servicing
Procedures not specically explained in this manual must
be performed only by a qualied technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.
If abnormal noise or vibration occurs, have the problem corrected before further use.
1. BEFORE EACH USE, inspect the general condition
of the tool. Check for loose screws, misalignment
or binding of moving parts, cracked or broken
parts, and any other condition that may affect its
safe operation. Do not use damaged equipment.
2. Occasionally, wipe the Wheel Chock down
with a soft cloth and mild detergent.
3. AFTER USE, wipe external surfaces
of the tool with clean cloth.
4. The Pivoting Bracket will close on the motorcycle
tire, securing the bike in an upright position.
5. For long-term storage, or if the Wheel Chock
is mounted to a mobile platform, secure the
motorcycle with belts or straps (not included).
Part Description Qty
1 Main Frame 1
2 Hex Bolt M10x20 4
3 Spring Washer 8
4 Flat Washer 4
5 Pivot Bolt M10x30 2
6 Bolt M10x70 4
7 Base 1
8 Nylon Sleeve 4
9 Large Washer 4
10 Hex Nut M10 6
11 Nylon Washer 2
12 Rubber Cap 4
13 Pivoting Bracket 1
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes
only, and are not available individually as replacement parts.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection veries the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specic legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Pittsburgh 60392 Owner's manual

Category
Power tools
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI