Miller JJ000000 Owner's manual
- Category
- Welding System
- Type
- Owner's manual
This manual is also suitable for
The Miller JJ000000 is an interface control designed for use with a DIALARC® HF welding power source. It provides a connection point for a remote contactor and amperage control device, allowing for precise control of the welding process. The unit comes with the necessary interconnecting cords for easy setup and can be placed on top of the welding power source or at a nearby location. It features a rugged construction, ensuring durability and reliability in demanding industrial environments.
The Miller JJ000000 is an interface control designed for use with a DIALARC® HF welding power source. It provides a connection point for a remote contactor and amperage control device, allowing for precise control of the welding process. The unit comes with the necessary interconnecting cords for easy setup and can be placed on top of the welding power source or at a nearby location. It features a rugged construction, ensuring durability and reliability in demanding industrial environments.
OWNER’S MANUAL
© 2011 MILLER Electric Mfg. Co.
FORM: OM-874D 093 324
MIC-4 Interface Control 2011−01
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Wear safety glasses with side shields.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Arc rays can burn eyes and skin − wear a welding helmet
with correct filter, and cover exposed skin with nonflam-
mable clothing.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Welding sparks can cause fire or explosion. Move flam-
mables away. Do not weld on closed tanks or barrels −
they can explode. Clean tanks or barrels properly.
Beware of electric shock from welding electrode or wiring.
Touching the electrode while in contact with the work or
ground can cause electric shock. Always wear dry
gloves. Keep all panels and covers closed.
Breathing welding fumes and gases can harm your
health. Welding requires good ventilation. If ventilation is
impossible, such as when welding in a confined space,
use an air-supplied respirator.
CALIFORNIA PROPOSITION 65 WARNINGS
Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in
some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm.
Wash hands after use.
2. Specifications and Location
ST-086 923-C
This unit is an interface control de-
signed for use with a DIALARC®
HF welding power source. This in-
terface control provides a connec-
tion point for a remote contactor and
amperage control device (not
supplied) such as an FTC-23,
RFCS-23, or equivalent. The nec-
essary interconnecting cords are
supplied with this unit to connect it
to the welding power source.
This control is equipped with two 6
ft. (1.8 m) cords for making connec-
tions to the welding power source
control circuitry. Lead lengths must
be considered when locating the
control. The control can be placed
on top of the welding power source
or at a nearby location.
The service life and efficiency of the
control are reduced when it is sub-
jected to high levels of dust, dirt,
moisture, corrosive vapors, and ex-
treme heat.
A 7-1/2 in.
(191 mm)
B 9-1/2 in.
(241 mm)
C 8-3/4 in.
(222 mm)
B
C
A
Weight:
7.5 lbs
(3.4 kg)
OM-874 Page 2
3. Connections
ST-086 923-C
1
2
3
1 Amperage Control Plug
Route and connect 3-prong plug
from control to welding power
source Remote Amperage
Receptacle.
2 Contactor Control Plug
Route and connect 2-prong plug
from control to welding power
source Remote Contactor
Receptacle.
3 Remote Control Receptacle
The remote control device is not
supplied with this unit. Obtain the
desired control (an FTC-23,
RFCS-23, or equivalent), and route
and connect plug to this receptacle.
See instructions supplied with the
remote device for proper operation.
Using the supplied adapter cord: Al-
lows remote controls with 14-pin
plugs to connect to the 5-pin remote
receptacle on MIC-4.
. For proper operation of this
control and the remote control
device, rotate the Amperage
Adjustment Control on the
welding power source to the
100 (maximum) position.
4. Routine Maintenance
! Turn Off all power before maintaining. Disconnect unit from power source before repairing or replacing cords.
3 Months
Replace
Cracked
Parts
Replace
Unreadable
Labels
Cord(s)
5. Troubleshooting
Trouble Remedy
No remote amperage control. Set switches and controls on welding power source to proper positions.*
Check weld output on welding power source.
Secure cord connections or replace cords, if necessary.
No remote output (contactor) control. Remote Hand Control switch in wrong position, control not so equipped, or poor connections.
Check switch settings, cord connections, and weld output on welding power source.
Secure cord connections or replace cords, if necessary.
*See welding power source Owner’s Manual.
OM-874 Page 3
6. Circuit Diagrams and Wiring Diagram
187 974
171 996-A
D
E
C
B
A
F
PLG51
D
C
E
B
A
RC51
X
SIL
Z
PLG50
50
CR50
505
504
506
501
503
BLK
502
WHT
GRN
BLK
WHT
4
7
B
A
CR
OM-874 Page 4
107 681-B
OM-874 Page 5
7. Parts List
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ST-086 922-B
Description Quantity
Part
No.
Dia.
Mkgs.
Item
No.
1 RC51 035 523 CONNECTOR, circ 5skt 16S rcpt Amphenol MS-3102A-16S-8S 1.. .... .... .. .......
2 PC1 085 617 CIRCUIT CARD, interface control 1.. ..... ..... .. .................................
3 073 756 STAND-OFF, No. 6-32 x .625 lg .250 hex female 4.. ............... .. ....................
4 086 000 CASE SECTION, base/front/rear 1.. ............... .. ..................................
5 +021 475 WRAPPER 1.. .............. .. .....................................................
6 019 677 HANDLE 1.. ............... .. .......................................................
7 134 327 LABEL, warning general precautionary 1.. ............... .. .............................
8 CR50 052 964 RELAY, encl 24VDC DPDT 1.. .... .... .. .......................................
9 139 041 BUSHING, strain relief 1.. ............... .. ..........................................
10 600 737 CABLE, port No. 16 3/c (order by ft) 6ft. .............. .. ...............................
11 170 593 PLUG, twlk 3P3W 20A 125V 1. .............. .. ......................................
12 039 618 PLUG, twlk 2P2W 20A 250V 1. .............. .. ......................................
13 604 988 CABLE, port No. 16 2/c (order by ft) 6ft. .............. .. ...............................
14 130 003 CABLE, adapter (consisting of) 1. .............. .. ....................................
039 273 CONNECTOR, circ 5pin 16S plug Amphenol MS-3106A-16S-8P 1................... .... .....
039 685 CONNECTOR, circ clamp str rlf sz 16 Amphenol 97-3057-8 1................... .... .........
151 146 CABLE, shld No. 22ga 5/c (order by ft) 2ft................... .... ...........................
152 568 CONNECTOR & SOCKETS, 1................... .... ....................................
143 922 CONNECTOR, circ clamp str rlf sz 17-20 Amp 206070-3 1................... .... ...........
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-874 Page 6
Notes
OM-874 Page 7
Notes
OM-874 Page 8
Notes
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Miller JJ000000 Owner's manual
- Category
- Welding System
- Type
- Owner's manual
- This manual is also suitable for
The Miller JJ000000 is an interface control designed for use with a DIALARC® HF welding power source. It provides a connection point for a remote contactor and amperage control device, allowing for precise control of the welding process. The unit comes with the necessary interconnecting cords for easy setup and can be placed on top of the welding power source or at a nearby location. It features a rugged construction, ensuring durability and reliability in demanding industrial environments.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller LJ000000 Owner's manual
-
-
-
Miller FTC-14 Owner's manual
-
-
-
-
-
-
