Version 07/01/2022 1/25
Shoe cabinet
2/25
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
3/25
Ax12
Ø6x35mm
Bx12
Ø15x10mm
Cx16
Ø6x30mm
Dx6
Ex3 Fx4 Gx6 Hx36
Ix6 Jx26 Kx3 Lx3
Mx2
Ø4x14mmØ4x10mm
E-1
E-2
Ø6x30mm Ø4x40mm
G-1 G-2 G-3
M-1 M-2
Ø4x14mm
Ø4x40mm
Ø3.5x14mm
Nx2
N-1 N-2
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
4/25
14
1
2
3
4
5
6
7
8
9
8
10
10
11
11
11
11
12
13
13
14
12
13
13
14
15
13
13
5/25
1Ax6
Ø6x35mm
Tighten Cam Bolt (A) to panel 2 panel 3
, as shown.
A
A
A
A
A
A
2
2
3
6/25
2
Please hammer the G-1 and G-2 onto the
2 and 3 boards, as shown.
G-1
3
2
3
3
G-2
G-1
G-1
G-1
G-1
G-1 G-2
G-2
G-2
G-2
G-2
Gx6
G-1 G-2
7/25
3Bx6
Ø15x10mm
Cx6
Ø6x30mm
Please turn No. 2 board and No. 3
board behind, INSERT SAWDUST C
into No. 5 board, No. 6 board and
No. 7 board respectively, then Lock
with Cam Lock B with No. 2 board
and No. 3 board respectively, as shown.
Back
Back
3
2
5
6
7
Front
BC
180°
42
B
B
B
BC
C
C
C
7
6
5
3
2
Please note that the
orientation of the
holes in the CAM Lock
is behind the cabinet
Back
Front
3
7
B
C
IIIIII
180°
8/25
4
Please use screw (J) to lock with
Iron Sheet (F) and plate No. 4
respectively, as shown.
Tighten Cam Bolt (A) to panel 1,
as shown.
1
1
A
J
J
J
J
J
F
4
4
A
A
A
A
A
Ax6
Ø6x35mm
Fx4 Jx20
Ø4x14mm
9/25
5
Insert wooden pins (c) at the bottom
of plate 2 and Plate 3 Plate 7,
as shown.
Use Screws (D) to lock plate No. 4
with plate No. 2 and Plate No. 3
Plate 7.as shown.
CD
4
3
C
C
C
C
D
D
D
DD
D
2
5
6
7
Cx5
Ø6x30mm
Dx6
Ø4x40mm
3
4
10/25
6
5
6
7
4
11
F
11
11
11
11
Please turn the number 11 pin to
the plate (F) screw lock respectively,as shown.
3
2
4
11/25
7
Wood pins (C) are inserted in the upper parts of Plate 2
and Plate 3;Insert number 8 and number 9 back plate
into the back plate slot of number 2 left side plate and 3
right side plate,as shown.
10
10
C
C
C
C
Cx4
Ø6x30mm
3
2
8
8
9
9
8
8
4
12/25
8
Lock Panel 1 with Panel 2 and Panel 3
Panel 5 with Cam Lock;
Wood pins (C) are inserted in the upper
parts of Plate 5,as shown.
180°B
CB
B
B
B B
1
1
Bx6
Ø15x10mm
Cx1
Ø6x30mm
2
3
5
IIIIII
13/25
9Jx6
Please use screw (J) to lock back plate No. 8,
No. 9 and No. 6 respectively,as shown.
2
3
8
8
9
4
6
J
J
J
J
J
J
Ø4x14mm
14/25
(1) Please fasten the E-1, E-2 and No. 12 plates with screws (H)
respectively,as shown.
2 Please use screw (L) to lock the handle (K) with plate
No. 14,as shown.
10
H
HH
E-2
H
H
H
E-1
E
12
12
12
x2
12
E-1
E-2
14
E-1
H
20
(1)
(2)
x2
Ex2 Hx16
E-1
E-2
Ø3.5x14mm
15/25
11
(1)Please fasten the E-1, E-2 and No. 13 plates with screws (H)
respectively as shown.
(2)Please fasten the screw (L) through the 12 plate and the handle (k),
as shown.
13
12
H
13
E-1
E-1
E-2
H
x2
(1)
(2)
12
E-1
12 K
L
x2
Hx4 Kx2 Lx2
Ø3.5x14mm
16/25
12
(1)Please fasten the E-1, E-2 and No. 15 plates with screws (H)
respectively as shown.
(2)Please fasten the E-1, E-2 and No. 14 plates with screws (H) respectively,
as shown.
15
E-1
H
HH
H
HH
E-2
15
15
E
(1)
15
E-1
E-2
14
E-1
H
14
(2)
H
Ex1 Hx8
E-1
E-2
Ø3.4x14mm
17/25
13
(1)Please fasten the E-1, E-2 and No. 13 plates with screws (H)
respectively as shown.
(2)Please fasten the screw (L) through the 15 plate and the
handle (k),as shown.
(1)
15
E-2
H
E-1
13
H
13
E-1
15 K
L
15
E-1
Hx2 Kx1 Lx1
(2)
Ø3.5x14mm
18/25
14
Please use screw (I) to lock (G-3) through plate E-1
and No. 2 and plate E-2 and No. 2 respectively as shown.
Gx4 Ix4
G-3
Ø4x10mm
1
2
3
15
12
E-2
G-3
I
E-2
E-2
E-1
E-1
G-3
G-3
G-3
I
I
I
E12
12
E
15
E
E
15
12
15
15
12
19/25
15
Please insert panel 13 into the cabinet as shown.
2
13
13
13
12
15
13
E-2
E-1
E-1
20/25
16
Please use screw H to lock the E-1 and E-2 with plate 13 respectively as shown.
Hx4
1
2
3
13
13
E-2
E-2
H
E-1
13
E-1 H
H
H
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
