Version:11/07/2022 1/22
Display Cabinet
2/22
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
3/22
Ax27
Ø6x35mm
Ø3x12mm
Ø3x14mm
Bx27
Ø15x10mm
Cx32
Ø6x30mm Ø4x35mm
Dx9
Ex28 Fx3 Gx6 Hx4
Jx4 Kx2 Lx4 Mx2
Nx2 Qx24
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
7
90°
D
7
8
6
6
7
8
D
D
D
Lock plate 8 with plate 6 and plate 7
with screws (D), as shown
F-1 F-2
M-1 M-2
N-1 N-2
Rx2
Ø3.5x14mm
Px20
P-1 P-2
R-1
R-2
Ø4x35mm
Ø3x16mm
4/22
DLx1 DRx1
CLx1
CL
DL
DR
CRx1
CR
300mm 300mm 300mm 300mm
5/22
1
2
4
6
5
7
8
4
19
18
18
20
21
22
23
9
3
14
16
15
15
17
17
10
12
12
13
11
6/22
1Ax4
2
Do not use an electric screwdriver, do not use
force during the rotation of the accessories,
otherwise it may cause the board to crack
Please pay attention to the holes where
the accessories are inserted
A
A
A
A
Bx2 Cx2
B
B
C
C
2
2
4
3
A
IIIIII
Ø15x10mm
Ø6x35mm
Ø6x30mm
B
C
Fix panel 4 to panel 2 using wooden dowel C,
then turn cam locks B clockwise to tighten,
as shown.
Insert quickfit screw A to corresponding holes
in panel 2&3.
180°
7/22
3
4
Bx2
Rx2
Cx2
B
B
C
C
R-1 R-1
E
E
E
R
R-1
R-2
R-1
R-2 R-1
R-1
R-2 R-2
R-1
11
2
3
4
R-1 R-2
IIIIII
Ex4
Ø15x10mm Ø6x30mm
Ø3x12mm
C
B
Fix panel 4 to panel 3 using wooden dowel C,
then turn cam locks B clockwise to tighten,
as shown.
180°
8/22
5
6
Ax4
Do not use an electric screwdriver, do not use
force during the rotation of the accessories,
otherwise it may cause the board to crack
C
C
C
C
B
B
B
B
Bx4 Cx4
1
24
3
A
A
A
A
A
1
IIIIII
B
Ø6x35mm
Ø6x30mmØ15x10mm
C
Insert quickfit screw A to corresponding
holes in panel 1.
Attach panel 1 to the assembled component using
wooden dowel C, then turn cam locks B clockwise
to tighten, as shown.
180°
9/22
7
8Ax4
2
4
12
12
13
3
Kx2 Lx4
Ø6x35mm Ø3x14mm
L
L
K
L
L
K
5
A
A
A
A
A
L
L
K
5
1
Slide panel 12 into available slots
as showm.
Please connect two panel 12 with
plank 13 at first.
Fix part K to panel 5 using screw L as shown.
Flip the plate, insert quickfit screw A into
corresponding holes with a screwdriver as
shown.
10/22
9Cx4
10
Dx4
E
E
E
EE
E
E
E
CL
CR
E
Ex6
6
7
Ø6x30mm Ø4x35mm
Ø3x12mm
ECL
Attach panel 5 to the assembled component
using wooden dowel C and screw D.
Fix runner CL&CR to panel 6&7 using screw E, as shown.
C
C
CC
D
D
D
D
2
4
5
3
C
D
1
11/22
11
12
Cx16
A
A
A
A
A
A
A
A
A
A
Ax10
C
C
C
C
C
CC
C
C
C
CCC
6
7
A
4
11
10
C
C
C
8
Ø6x35mm
Ø6x30mm
C
Insert quickfit screw A into corresponding
holes in panel 6 and 7 with a screwdriver
as shown.
Attach panel 11 to panel 10 with wooden
dowel C.
Insert wooden dowel C into panel,
10,11,4 and 8 as shown.
12/22
13
Bx5
B
BB
B
B
B
14
Bx5
B
B
B
B
B
B
8
4
10
11
6
6
8
4
11
10
IIIIII
IIIIII
7
Ø15x10mm
Ø15x10mm
Attach panel 8,4,10 to panel 6, then turn cam
locks B clockwise to tighten, as shown.
Attach panel 7 to assembled component, turn
cam locks B clockwise to tighten, as shown.
180°
180°
13/22
15
Gx6
16
G
G
GG
G
GG
6
6
15
10
11
15
16
47
7
Knock foot peg G into bottom of the
unit as shown.
Slide panel 15 into available
slots as shown.
Please connect two panel 15
with plank 16 at first.
14/22
17
Bx4 Cx4
C C
B
B
B
B
CC
IIIIII
2
6
Ø15x10mm Ø6x30mm
B
C
Fix 2 assembled components using
wooden dowel C, turn cam locks B
clockwise to tighten, as shown.
180°
15/22
18
19
Hx4
H
H
H
H
2
6
214
6
H
Insert part H into panel 2 and 3.
Place panel 14 in as shwon.
16/22
20
Dx5
Ax5 Bx5
A
A
A
B
A
A
D
D
D
D
D
BB
BB
22
22
23
9
20
21
19
19
20
20
19
IIIIII
A
Ø6x35mm Ø15x10mm Ø4x35mm
D
B
B
9
9
Insert quickfit screw A into corresponding holes
in panel 9 as shown.
Attach panel 19,20 and 22 to panel 9 then.
Slide panel 23 into grooves, and turn all cam
locks B clockwise to tighten as shown.
Fix panel 21 to the
component using
screw D as shown.
180°
17/22
21
22
Fx1
Ex6 DLx1 DRx1
DL
DR
F-1 F-2
F-1
F-1
F-2
E
E
E
E
E
E
E
E
EDL
DR
20
19
F-1
F-2
F-1
Ø3x12mm 300mm 300mm
DR
9
9
Fix handle F-2 to panel 9 using screw F-1
as shown.
Fix runner DL and DR to panel 19 and
20 respectively using screw E as shown.
16
Ex16
18/22
23
24
Qx8 Fx2 Jx4
F-1
F-1
F-2
J
QQ
J
Q
Q
J
Q
Q
x2
F-1 F-2
18
2
6
Ø3.5x14mm
DL
CL
9
Align rails, slide the drawer.
Fix hing J to panel 18 using screw(Q) as shown.
Fix handle F-2 using screw F-1 as shown.
19/22
25
Ex12 Qx16
Qx4
J
Qx4
Ex2
J
Ex2
Ex2
17
18
18
17
17
J
QQ
QQ
J
Q
Q
QQ
2
6
Ø3x12mm Ø3.5x14mm
E
E
Attach panel 17 to upper side by fixing hinge
using screw E as shown.
Attach panel 18 to lower side panels by fixing
hinge with screw Q as shown.
N-1
N-2
15
15
N-1
N-2
N-1
N-2
20/22
26
Px20 Nx2
P-1 P-2 N-1 N-2
7
3
12
13
16
12
x20
P-1
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P-2
P-1
Ø3x16mm
Reinforce back panel using part P-1 with
screw P-2 as shown.
Fix N-1 to back panel using screw N-2
as shown.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
