1/1
Version:12/20/2022 3
Sideboard
2/13
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
3/13
Ax6
Ø6x35mm
Bx6
Ø15x12mm
Cx12(+1)
Ø8x30mm Ø4x33mm
Ø3.5x12mm
Ø4x14mm
Ø5x16mm
Dx2
Ex6 Fx2 Hx16(+1)
Ix16 Jx8 Kx4 Lx4
Mx4 Ox2
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Nx2
Ø6.3x50mm
Gx32(+3)
(+1)
Ø5x10mm Ø6x30mm
Px2
Ø4x15mm
4/13
1
2
3
4
5
5
6
7
8
8
8
8
9
9
10
11
12
13
5/13
1
2
A
A
Ax6
Ø6x35mm
11
F
F
Fx2
Bx6 Cx6
Ø8x30mmØ15x12mm
IIIIII
B
C
2
3
4
1
F
F1 2
Screw quickfit screw(A) into corresponding
holes in plate 1 with a screwdriver as shown.
Fix part(F1) to plate 1 using screw(F2) as shown.
Attach plate 2,3 and 4 to plate 1 with wooden
dowel(C), put cam lock(B) into holes in plate 2,3,4
and turn clockwise to tighten as shown.
6/13
3
4Ex6 Cx6
Ø8x30mmØ6.3x50mm
1
5
5
4
4
5
5
6
6
Slide back plate 5 along
grooves as shown.
Attach plate 6 to the bottom of the component
with wooden dowel(C), and fix using screw(E)
as shown.
7/13
5
6
6
8
8
8
8
7
Ø3.5x12mm
Hx16
Ix16 Mx2
Ø5x10mm
Ox2
Ø4x15mm
Px2
1
1
P
O
M
6
5
5
4
Ø4x14mm
G
Ø3.5x12mm
H
I
H
5
E
Rotate leg 8 and leg support 7
into plate 6 as shown.
Reinforce back plate using part(I) with screw(H)
as shown.
Fix anti-tipping device(P) to plate 1
using washer(M) with screw(O)
as shown.
8/13
Kx4
Please note, Kx4 are used to embed the cabinet body inside the cabinet
door, and the cabinet door is flush with the side panel, and Lx4 are applied
Lx4
to two cabinet doors sharing a side panel.
9/13
7
8
9
9
Ø5x16mm
Jx8
J4
4
3
2
Lx4
Ø4x14mm
Gx8
11
12
L
L
L
L
UP
UP
L
G
Insert part(J) into holes in plate 2,3 and 4,
place shelf 9 in as shown.
Fix hinge(L) to plate 11 and 12
respectively using screw(G)
as shown.
G
Ø4x14mm
Ø3.5x12mm
H
L
K
10/13
9
10
13
K
K
K
K
UP
UP
10
K
G
Kx4
Ø4x14mm
Gx8
Ø4x14mm
Gx8
G
4
2
10
13
13
UP
UP
Ø4x14mm
G
Ø3.5x12mm
H
Fix hinge(K) to plate 10 and 13 respectively
using screw(G) as shown.
Attach door plate 10 to plate 2;
door plate 13 to plate 4 by fixing
hinge(K) with screw(G) as shown.
Ø4x14mm
G
Ø3.5x12mm
H
L
K
K
11/13
12
Ø4x14mm
Gx8
G
3
11 12
11
UP
11
Ø4x14mm
G
Ø3.5x12mm
H
Press the door to open.
Please note, if rebound device are stuck,
Attach door plate 11 and 12 to
plate 3 by fixing hinge(L) with
screw(G) as shown.
just loosen screws(F) a little.
L
F
12/13
13
If there is misalignment after you install,
adjust the screw to the best condition
13/13
14
WALL
drilling hole
Ø6x30mm
WALL WALL WALL
x2 x2 x2
N
Install anti-tipping device as shown.
N
Dx2 Nx2
Ø6x30mm
Ø4x33mm
Mx2
Ø5x10mm
D
M
P
1
1
/
