2. Panduit
  3. 1005512

Panduit 1005512 User manual

  • Hello, I've reviewed the Panduit Installation Instructions for the Stainless Steel Quad Cable Cleat. This document outlines the mounting procedures, necessary torque specifications, and the proper use of included hardware. The cleats are designed for quad cable arrangements and offer two mounting methods. I'm ready to answer your questions about the installation process and the different components of the cleat.
  • What is the recommended torque for the swing bolt when using the mounting bracket?
    What is the recommended torque for the securing bolt when mounting directly with fasteners?
    What should I do if the flanges of the shells come together before the torque is met?
    In which cases I need to remove top plastic spacer?
Stainless Steel Quad Cable Cleat
Cable Cleat for the Protection and Support
of Insulated Power Cables in Quad Arrangement
1005512
Rev. 01
[11-2021]
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2021
TO REDUCE THE RISK OF INJURY, USER
MUST READ INSTALLATION INSTRUCTIONS
BEFORE ATTEMPTING TO INSTALL
NOTE: In the interest of higher quality and value, Panduit products are
continually being improved and updated. Consequently, pictures
may vary from the enclosed product.
NOTE: Updates to this Installation Instructions may be available. Check
www.panduit.com for the latest version of this manual.
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 2 of 8 Rev 00 [09-2021]
Email:
techsupport@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
www.panduit.com
Panduit Corp.
USA Technical Support
Tel: 800-777-3300
Panduit Europe • EMEA Service Center
Tel: +31 546 580 452 • Fax: +31 546 580 441
Preparing for Order
Step
Picture
Description
1
Contact Panduit Sales for
assistance with cleat and
hardware selection.
2
Measure actual diameter of
the cables. Select a cleat part
number based on the actual
diameter of the cables.
3
If using a mounting bracket to
secure cleat, measure height
of the ladder rung and
reference chart below. If
using a bolt to secure cleat,
procure M8 or 5/16” bolts,
washers, and nuts with
sufficient length to pass
through the ladder rung.
Rung Height
Mounting Bracket Part Number
15mm (.59”) or less
CBH15L50-V6
15mm (.59”) to 20mm (.79”)
CBH20L50-V6
20mm (.79”) to 25mm (1.01”)
CBH25L50-V6
25mm (1.01”) to 30mm (1.16”)
CBH30L50-V6
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 3 of 8 Rev 00 [09-2021]
Cable Cleat Nomenclature
Start on Page 3 if installing by Mounting Bracket.
Start on Page 6 if installing with Mounting Fasteners.
Cleat Clamshell Top
Fastening Bolt, Washer, and
Locknut (Included in Package)
Cleat Clamshell Bottom
Bottom Plastic Spacer
Top Plastic Spacer
Mounting Bracket
Swing Bolt with
Flanged Nut
Slotted Ladder Rack/Rung
Unslotted Ladder Rack/Rung
Quad Cable Bundle
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 4 of 8 Rev 00 [09-2021]
Mounting Method 1: Mounting Bracket
Step
Picture
Description
1
OR
Measure the cable diameter.
Refer to the chart on page 8.
In some instances, the top
spacer will need to be
removed before installation.
2
Insert mounting bracket into
slot in bottom plastic spacer
of cable cleat.
3
Slide cleat and mounting
bracket over rung in the
desired position on the rung.
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 5 of 8 Rev 00 [09-2021]
4
Rotate swing bolt until the
carriage head rests within
the matching opening in the
top of the mounting bracket.
Tighten flange nut to 60 in-
lbs [6.8Nm].
5
Open top clamshell and
place quad cables in the
opening in a quad
configuration. Close top
clamshell around the cables.
6
Assemble included nut and
washer onto the securing
bolt. Tighten to 15 ft-lbs
[20.3Nm].
In some cases, the flanges
of the shells will come
together before the torque is
met. In other cases, there
will be a gap between the
flanges after the torque is
met.
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 6 of 8 Rev 00 [09-2021]
Mounting Method 2: Mounting Fasteners
Step
Picture
Description
1
Remove top plastic spacer
to allow access to the bolt
hole.
2
Position cleat over the
appropriate hole or slot in
the rung. Assemble securing
bolt through the hole in the
bottom of the cleat.
A carriage bolt is shown
however in some
circumstances a hex bolt
might be used.
Locking nuts and/or washers
are recommended if
fasteners could become
loose over time.
3
Tighten securing bolt to 120
in-lbs [13.6Nm].
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 7 of 8 Rev 00 [09-2021]
4
OR
Measure the cable diameter.
Refer to the chart on page 8.
In some instances, the top
spacer will need to be re-
installed before installation.
5
Open top clamshell and
place cables in the opening
in a quad configuration.
Close top clamshell around
the cables.
6
Assemble included nut and
washer onto the securing
bolt. Tighten to 15 ft-lbs
[20.3Nm].
In some cases, the flanges
of the shells will come
together before the torque is
met. In other cases, there
will be a gap between the
flanges after the torque is
met.
© Panduit Corp. 2021
INSTALLATION INSTRUCTIONS
1005512
Rev. 00 [09-2021]
DOC#: 1005512 Page 8 of 8 Rev 00 [09-2021]
Spacer Decision Table
Part Number
Cable
Range
With Top
Spacer
Without Top
Spacer
CCSSQD2226-X
22 – 26mm
22 – 24mm
24 – 26mm
CCSSQD2529-X
25 – 29mm
25 – 27mm
27 – 29mm
CCSSQD2834-X
28 – 34mm
28 – 31mm
31 – 34mm
CCSSQD3339-X
33 – 39mm
33 – 36mm
36 – 39mm
CCSSQD3844-X
38 – 44mm
38 – 41mm
41 – 44mm
/