2. Lian Li
  3. Uni Fan SL-INF

Lian Li Uni Fan SL-INF Installation guide

  • Hello! I'm a chat assistant and I've reviewed the installation guide for the LIAN LI UNI FAN SL-INF RGB. I'm familiar with the fan connection methods, power module installation, and controller usage, and also with the restrictions of the controller. Feel free to ask me any questions about the device and its installation.
  • How to connect fans together?
    How can I change the cable orientation on the power module?
    What are the controller cable connection options?
    What is the maximum power output of the controller?
    What is the number of fans supported when using a static white color set to full brightness?
安裝指南
Power Module Installation /
Fan to Fan Connection /
Steps to Switch Orientation of the Cable on the Power Module /
電源⽚安裝
-
⾵扇連接⾵扇
電源⽚電線轉換⽅向⽰意
注意!電源⽚分為⼤⼩兩種卡榫 安裝時須，
Note! The socket for the power module
are in different size, please be aware of
the direction.
Installation Guide /
!
包裝內容物
Package Contents /
x 1 pc
注意⽅向性。
注意!若遇到⽔冷排出⽔位置影響電源⽚上
蓋 可將上蓋移除 以垂直⽅式⾛線， ， 。
Note! The top cover is removable if it is
affected by the radiator inlet and outlet,
and route the cable vertically.
!
x 3 pcs
x 4 pcs
x 1 pc
x 1 pc
x 1 pc
1
2
Fixed
Release
Fixed
Release
Remove Release
Fixed
4 5 6
1 2 3
1
2
A 5銅板紙或模糙紙100P單 色雙面印 刷摺1摺 成A6
x 12 pcs
UNI FAN SL-INF RGB
控制器線材連接
⾵扇扣鎖拆除
注 意!若 遇 到 ⽔ 冷 排 出 ⽔ 位 置 影 響 ⾵ 扇 扣 鎖 可 將 ⾵ 扇，
卡扣鎖移除。
Note! The fan interlocking key is removable if it is
affected by the radiator inlet and outlet.
!
Controller Cable Connection /
Note! Press and pull out
the connector to release
the cable.
注意!按下 再拉出線材
接頭。
!
Remove the adhesive
撕下雙⾯膠
Use of Magnetic Adhesive Pad / 磁 性 膠 墊 使 ⽤
1
G50.12SLIN3.00
2
控制器 2 個 SATA 15 PIN線材電源全接情況下 最⼤ 輸出如下：，
1.控制器最⼤輸 出為 29 W。
2.採⽤ L-Conne c t 3󰔥軟體控制⾵扇設為定⾊⽩光 請將⽩光亮度降低， 。
3.同步主機板亮度開⾄ 1 00%的定⾊⽩光時 最多⽀援8顆infini t y Fan， 。
4.控制器上的SM type輸出⼝最⼤⽀援5 W (控制器上有2個 SM t ype輸出⼝)。
Restriction of Controller / 控 制 器 的 限 制
Maximum output of controller when connected BOTH SATA 15 PIN cable:
1. The maximum total output of the controller supports up to 29W.
2. Use L-Connect 3 to set static white, please lower the brightness.
3. When sync to motherboard and set as 100% brightness of static white, the
controller supports up to 8 UNI FAN SL Infinity.
4. Each SM type port supports up to 5W. (2 SM type port on controller)
Connect to USB
Connect to 5V ARGB
3 pin header
警告!請不要連接 錯誤類型 的
LED接頭 如果連接到12V接 ⼝， ，
將造成永久損壞。
Warning! Do not connect the
wrong type of LED connector. If it is
connected to the 12 V connector,
permanent damage will occur.
5 V 12 V
!
Connect to
PSU SATA 15 Pin
Connect to
1, or 2, or 3, or 4, or
splitt cable
1
34
2
* Splitter
*
GND VCC
DATA
- Control with L-Connect 3:
Connect up to 8 UNI FAN SL Infinity with splitter
when set as static white, lower the brightness if
necessary.
- Control with Motherboard software:
Connect up to 5 UNI FAN SL Infinity with splitter
when set as 100% brightness static white
分 接 線
* Splitter /分 接 線
Press
1 2 3
連接到1或2或3，，，
或4或分接線，
!
Remove the Fan Interlocking Key /
SM
Type
-採⽤ L-C o n n e c t 3軟體控制燈效：
　󰔥， ，使⽤此轉接線串接 8󰔥顆⾵扇 並設定為定⾊⽩光
　。將⽩光亮度降低
-同步主板燈效軟體：
　， ，亮度開⾄󰔥1 00 %󰔥定 ⾊⽩光模式 使⽤此轉接線材
　。最多⽀援 5󰔥顆 In f i n i t y Fa n
/