Maxcess DS-25 Kantiroller Installation guide

Brand: Maxcess

Model: DS-25 Kantiroller

Type: Installation guide

Maxcess DS-25 Kantiroller

The Maxcess DS-25 Kantiroller is a versatile and precise web guiding system designed to maintain accurate web alignment in various industrial applications. It features a compact and rugged construction, making it suitable for demanding environments.

The Kantiroller operates on the principle of edge detection, utilizing an integrated sensor to monitor web position. This information is processed by an advanced control algorithm, which adjusts the position of the guide rollers to correct any misalignment.

The DS-25 Kantiroller offers several key capabilities:

Precise Web Guiding: With its high-resolution sensor and sophisticated control system, the Kantiroller ensures accurate web alignment, minimizing edge flutter and maintaining consistent web tension.

Maxcess DS-25 Kantiroller

The DS-25 Kantiroller offers several key capabilities:

Precise Web Guiding: With its high-resolution sensor and sophisticated control system, the Kantiroller ensures accurate web alignment, minimizing edge flutter and maintaining consistent web tension.

INSTALLATION INSTRUCTIONS

DS-25 KANTIROLLER

1of 28/12/2005

Fife Corporation

P.O. Box 26508, Oklahoma City, OK 73126, USA

Phone: 405.755.1600 / Fax: 405.755.8425

www.fife.com / E

-mail: [email protected]

1. Install the DS-25 Kantiroller Guide in the

process line such that the rollers, when in the

servo center position, are parallel to the entry

and exit rollers.

2. The DS-25 must be installed on a flat,

machined surface that is flat within 0,5 [0,02]

total indicated runout.

3. Ensure that the WEB DIRECTION ARROW on

the guide is pointed in the direction of web

travel.

Figure 1.

DS-25 KANTIROLLER WITH

PROCESSOR AND INTEGRATED

SENSOR MOUNTING

Dimensions are mm [inches]

INSTALLATION INSTRUCTIONS

DS-25 KANTIROLLER

2of 28/12/2005

Fife Corporation

P.O. Box 26508, Oklahoma City, OK 73126, USA

Phone: 405.755.1600 / Fax: 405.755.8425

www.fife.com / E

-mail: [email protected]

1. For satisfactory guideing results, do not

exceed a maximum of 508 mm [20 in] in the

free entering web span. The greater the error

to be corrected, the greater the required free

entering span must be. Also, stiff webs under

high tension require long entering spans;

fllexible webs under low tension will require

less.

2. Install the sensor downstream from the DS-25

Kantiroller and as close to it as practical. The

sensor should never be farther from the guide

roll than ½ of the exiting span.

3. Where it is needed, a roller or a deadbar

should be used to hold the plane of the exiting

web constant and stabilize the web edge at

the sensor.

4. Integrated processor and sensor mounting is

optional. Integrated sensor mounting is only

available for wrap styles exiting towards the

raceway base.

Table A. General Specifications

Available Roll Face (F), mm [in] 160 [6,30], 200 [7,88], 250 [9,84]

Maximum Correction (Jmax), mm [in] 0,05 x L + 9,9 [0,05 x L + 0,39]

Maximum Tension (Tmax), N [lbs] 150 [34], for ‘S’ wrap styles

Maximum Tension (Tmax), N [lbs] 200 [45], for other wrap styles

Maximum Actuator Thrust (Tmot), N [lbs] 222 [50]

Maximum Actuator Speed (Vmot), mm/s [in/s] 56 [2,2]

Maximum Correction Speed (Vcorr), mm/s [in/s] Jmax x 3,72 [Jmax x 3,72]

Maximum Operating Temperature °C [°F] 60 [140]

Weight, kg [lbs] 8,6 [19]

Maxcess DS-25 Kantiroller Installation guide

Brand: Maxcess

Model: DS-25 Kantiroller

Type: Installation guide

Maxcess DS-25 Kantiroller

The DS-25 Kantiroller offers several key capabilities:

Precise Web Guiding: With its high-resolution sensor and sophisticated control system, the Kantiroller ensures accurate web alignment, minimizing edge flutter and maintaining consistent web tension.

Download PDF

report

Maxcess DS-25 Kantiroller Installation guide

Maxcess DS-25 Kantiroller Installation guide

Related papers

Other documents