Sanus CFR524 Quick start guide

Brand: Sanus

Model: CFR524

Type: Quick start guide

This manual is also suitable for

Sanus Systems

2221 Hwy 36 West

Saint Paul, MN 55113 USA

Customer Service

Americas: 800-359-5520 • 651-484-7988 • [email protected]

Europe, Middle East, and Africa: 31 (0) 40 26 68 619 • [email protected]om

Asia Paciﬁc: 86 755 8996 9226 • 800 999 6688 (mainland China only) • sanus.ap@milestone.com

sanus.com

All other brand names or marks are used for identiﬁcation purposes and are trademarks of their respective owners.

CFR518, CFR524, & CFR535

(6901-002027 <00>)

6901-002027 <00>

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS - PLEASE READ ENTIRE MANUAL BEFORE USING THIS PRODUCT

Thank you for choosing a Sanus Foundations Component Series Rack. The CFR518, CFR524, and CFR535 are designed to support audio/video equipment.

Ù The total weight capacity for the CFR518 is 453.6 kg (1,000 lbs).

Ù The total weight capacity for the CFR524 is 453.6 kg (1,000 lbs).

Ù The total weight capacity for the CFR535 is 453.6 kg (1,000 lbs).

CAUTION:

CAUTION: Avoid potential personal injuries and property damage!

Ù Do not use this product for any purpose not explicitly specied by Sanus Systems.

Ù If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact Sanus Systems

Customer Service or call a qualied contractor.

Ù Sanus Systems is not responsible for damage or injury caused by incorrect assembly or use.

WARNING:

WARNING: Avoid potential personal injuries and property damage!

Ù Do not exceed the stated weight capacities.

Ù Do not shake, tilt, rock, sit, stand, or climb on your Component Series Rack. Tipping may cause injury or death.

Ù Do not move large racks by yourself; due to weight and height, assistance is required.

6901-002027 <00>



Choose an Option

Do Not Loosen/Tighten Note This End Up.

LEGEND

WARNING This product

contains small items that

could be a choking hazard

Tools Required Caution/Warning Repeat Step Heavy! Assistance Required.

OPT

Electrical Warning

Troubleshooting and

Maintenance

Tip Hazard Optional

6901-002027 <00>

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Sanus

Systems Customer Service. Never use damaged parts!

Supplied Parts and Hardware

[02] x 4

[03] x 4

[04] x 16 [05] x 16 [06] x 16

[01] x 1

6901-002027 <00>

CAUTION:

Install feet [02] (recommended) and adjust them as neccessary to level the rack – OR – install castors [03].

DO NOT install both feet [02] and castors [03].

CAUTION: To avoid potential injury or property damage, always ensure that your rack is level.

Step 1

[02]

[03]

[05]

[04]

[06]

6901-002027 <00>

Numerous knockouts (K) are provided for cable management. You can route your cables through the knockouts or through the opening (O) in the bottom

panel.

CAUTION: All knockouts that are used for wires without conduit must have bushings inserted in the knockout to eliminate damage to the cable's insulation.

Step 2

OPT

CAUTION:

(K)

(O)

6901-002027 <00>

Remove the venting panel for additional ventalation.

CAUTION: To avoid damage to your components due to overheating, ensure that there is adequate space between each unit for proper airow. It is

important to maintain an operating temperature inside of the rack that does not exceed 104°F (40°C).

Step 3

OPT

CAUTION:

6901-002027 <00>

Adjust the rails within one slot – OR – adjust the rails into any of the slots provided.

NOTE: Be sure to adjust the top (T), bottom (B), right (R), and left (L) rails evenly.

Step 4

OPT

(T)

(B)

(T)

(B)

(R)

(L)

(R)

(L)

6901-002027 <00>

Verify that your grounding wire (W) is installed to the bottom rail hole (H) and the base ground stud (S) on the rack.

CAUTION: Avoid potential injury or property damage! The grounding wire must be properly installed at all times.

Step 5

CAUTION:

(S)

(H)

(W)

6901-002027 <00>

Milestone AV Technologies and its a liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation

or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty,

expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or su ciency of the information contained in this

document.