Toro TX 525 Wide Track Compact Utility Loader User manual

TX525

Service Manual

Sitework Systems

Form No. 492-9195

This service manual was written expressly for Toro service technicians. The Toro company has made every effort to

make the information in this manual complete and correct.

Basic shop safety knowledge and mechanical/electrical skills are assumed. The Table of Contents lists the systems

and the related topics covered in this manual.

For service information on drive systems, please refer to the Hydro-Gear BDP-10A/16A/21L Pump service manual

(form no. 492-4789), Hydro-Gear P Series Pump service manual (form no. BLN 52503) and Parker-Ross TF wheel

motor service manual (form no. 492-4753). For information specic to the engines used on this unit, refer to the

appropriate engine manufacturer’s service and repair instructions.

Units covered on in this manual are: TX525 Wide and Narrow Track, model years 2007 - current

The manual may also be specied for use on later model products.

The hydraulic power system is precision machinery. Maintain strict cleanliness control during all stages of service

and repair. Cover or cap all hose ends and ttings whenever they are exposed. Even a small amount of dirt or other

contamination can severely damage the system.

We are hopeful that you will nd this manual a valuable addition to your service shop. If you have any questions or

comments regarding this manual, please contact us at the following address:

The Toro Company

LCB Technical Services

8111 Lyndale Avenue South

Bloomington, MN 55420

The Toro Company reserves the right to change product specications or this manual without notice.

ABOUT THIS MANUAL

ii Rev. 000 TX525 Service Manual

8/01/10Revision 000 . . . . . . . . . . . . .

REVISIONS

iiiTX525 Service Manual Rev. 000

TABLE OF CONTENTS

SAFETY INFORMATION

General Information ......................................................................................................................1-1

Think Safety First..........................................................................................................................1-1

SPECIFICATIONS

General Specications..................................................................................................................2-1

Dimensions ...................................................................................................................................2-1

Periodic Maintenance Items .........................................................................................................2-2

Performance (Narrow Track) ........................................................................................................2-2

Performance (Wide Track)............................................................................................................2-2

Hydraulic System..........................................................................................................................2-3

Hydraulic System cont. .................................................................................................................2-4

Electrical System ..........................................................................................................................2-4

Track System ................................................................................................................................2-4

Torque Specications ...................................................................................................................2-5

Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Inch Series) ....................................2-6

Standard Torque for Dry, Zinc and Steel Fasteners (Metric Series) .............................................2-7

Other Torque Specications .........................................................................................................2-8

Equivalents and Conversions .......................................................................................................2-9

U.S. to Metric Conversions .........................................................................................................2-10

MAINTENANCE

Recommended Maintenance Schedule........................................................................................3-1

Greasing the Traction Unit ............................................................................................................3-2

Maintaining the Road Wheels.......................................................................................................3-3

Hydraulic Reservoir Tank ..............................................................................................................3-4

Location .................................................................................................................................3-4

Checking the Hydraulic Fluid .................................................................................................3-4

Replacing the Hydraulic Filter.......................................................................................................3-5

Changing the Hydraulic Fluid .......................................................................................................3-6

Checking the Hydraulic Lines .......................................................................................................3-7

Vents - Hydraulic Tank ..................................................................................................................3-7

Engine Servicing...........................................................................................................................3-8

Servicing the Cooling System.......................................................................................................3-9

Cleaning Radiator ..................................................................................................................3-9

Engine Coolant ......................................................................................................................3-9

Changing Engine Coolant ....................................................................................................3-10

Changing Engine Coolant Assembly ....................................................................................3-14

Fuel System................................................................................................................................3-18

Drain & Clean Fuel Tank ......................................................................................................3-18

Fuel Tank Removal ..............................................................................................................3-19

Fuel Tank Installation ...........................................................................................................3-21

Replacing the In-Line Fuel Filter (Serial numbers 280000500 & higher) .............................3-24

Air Filter ......................................................................................................................................3-24

Fuse Block ..................................................................................................................................3-25

Hydrostatic Pump Belt ................................................................................................................3-25

Alternator/Fan Belt......................................................................................................................3-26

Track Inspection .........................................................................................................................3-27

Battery Maintenance...................................................................................................................3-28

Testing ........................................................................................................................................3-29

Special Tools ..............................................................................................................................3-30

iv Rev. 000 TX525 Service Manual

TABLE OF CONTENTS

ENGINE

Radiator & Oil Cooler Replacement .............................................................................................4-1

Radiator & Oil Cooler Assembly Removal .............................................................................4-1

Oil Cooler Removal ................................................................................................................4-6

Oil Cooler Installation .............................................................................................................4-7

Radiator Removal ................................................................................................................4-10

Radiator Installation .............................................................................................................4-12

Radiator & Oil Cooler Assembly Installation ........................................................................4-15

Mufer Assembly & Air Cleaner Assembly Removal ..................................................................4-21

Glow Plug, Fuel Injector Access ..........................................................................................4-21

Mufer Removal ...................................................................................................................4-21

Air Cleaner Assembly Removal ...........................................................................................4-23

Air Cleaner Assembly & Mufer Assembly Installation .........................................................4-24

Air Cleaner Assembly Installation ...............................................................................................4-24

Mufer Installation ......................................................................................................................4-25

Alternator Replacement ..............................................................................................................4-27

Alternator Removal ..............................................................................................................4-27

Alternator Mounting Styles ...................................................................................................4-28

Alternator Installation ...........................................................................................................4-32

Checking the Alternator Belt Tension ...................................................................................4-37

Cooling Fan Replacement ..........................................................................................................4-37

Cooling Fan Removal ..........................................................................................................4-37

Cooling Fan Installation .......................................................................................................4-38

Flywheel Replacement ...............................................................................................................4-40

Flywheel Removal ................................................................................................................4-40

Flywheel Installation .............................................................................................................4-44

Starter Replacement...................................................................................................................4-49

Starter Removal ...................................................................................................................4-49

Starter Installation ................................................................................................................4-52

Starter Solenoid Replacement....................................................................................................4-55

Starter Solenoid Removal ....................................................................................................4-55

Starter Solenoid Installation .................................................................................................4-59

Engine Removal .........................................................................................................................4-64

Engine Component Removal ...............................................................................................4-87

Engine Installation ......................................................................................................................4-96

Engine Component Installation ............................................................................................4-96

Engine Assembly Installation ............................................................................................. 4-110

Checking, Adding & Bleeding the Engine Coolant ...................................................................4-138

Throttle Cable Adjustment ........................................................................................................4-142

Throttle Cable Replacement .....................................................................................................4-144

Throttle Cable Removal .....................................................................................................4-144

Throttle Cable Installation ..................................................................................................4-147

Alternator Assembly Teardown .................................................................................................4-153

Alternator Testing ......................................................................................................................4-159

Stator .................................................................................................................................4-159

Rotor ..................................................................................................................................4-160

Slip Ring .............................................................................................................................4-161

Brush Wear ........................................................................................................................4-161

Rectier ..............................................................................................................................4-162

IC Regulator .......................................................................................................................4-162

Alternator Reassembly .............................................................................................................4-163

Starter Assembly Teardown ......................................................................................................4-171

Starter Assembly Rebuild .........................................................................................................4-180

vTX525 Service Manual Rev. 000

TABLE OF CONTENTS

ENGINE cont.

Starter Assembly Testing ..........................................................................................................4-188

Brush Wear ........................................................................................................................4-188

Brush Holder ......................................................................................................................4-188

Armature Coil .....................................................................................................................4-189

Field Coil ............................................................................................................................4-189

ELECTRICAL

Electrical .......................................................................................................................................5-1

Heat Shield Removal .............................................................................................................5-1

Ignition Switch ..............................................................................................................................5-2

Purpose ..................................................................................................................................5-2

Location .................................................................................................................................5-2

How It Works ..........................................................................................................................5-2

Testing ....................................................................................................................................5-3

Hour Meter....................................................................................................................................5-3

Purpose ..................................................................................................................................5-3

Location .................................................................................................................................5-3

How It Works ..........................................................................................................................5-4

Testing ....................................................................................................................................5-4

Fuel Gauge ...................................................................................................................................5-4

Purpose ..................................................................................................................................5-4

Location .................................................................................................................................5-4

How It Works ..........................................................................................................................5-4

Testing ....................................................................................................................................5-4

Relay ............................................................................................................................................5-5

Purpose ..................................................................................................................................5-5

Location .................................................................................................................................5-5

How It Works ..........................................................................................................................5-5

Testing ....................................................................................................................................5-6

Engine Oil Pressure and Battery Charge Indicator Light Cluster .................................................5-6

Purpose ..................................................................................................................................5-6

Location .................................................................................................................................5-6

How It Works ..........................................................................................................................5-7

Testing - Oil Pressure Light ....................................................................................................5-7

Testing - Battery Charge Light ...............................................................................................5-7

Water Temperature and Glow Plug Indicator Light Cluster...........................................................5-7

Purpose ..................................................................................................................................5-7

Location .................................................................................................................................5-7

How It Works ..........................................................................................................................5-8

Testing - Water Temperature Light .........................................................................................5-8

Testing - Glow Plug Light .......................................................................................................5-8

Glow Plug Switch..........................................................................................................................5-8

Purpose ..................................................................................................................................5-8

Location .................................................................................................................................5-8

How It Works ..........................................................................................................................5-9

Testing ....................................................................................................................................5-9

Water Temperature Sender ..........................................................................................................5-9

Purpose ..................................................................................................................................5-9

Location .................................................................................................................................5-9

How It Works ........................................................................................................................5-10

Testing ..................................................................................................................................5-10

vi Rev. 000 TX525 Service Manual

TABLE OF CONTENTS

ELECTRICAL cont.

Oil Pressure Switch ....................................................................................................................5-10

Purpose ................................................................................................................................5-10

Location ...............................................................................................................................5-10

How It Works ........................................................................................................................5-10

Testing ..................................................................................................................................5-10

Neutral Proximity (Magnetic) Switch........................................................................................... 5-11

Purpose ................................................................................................................................ 5-11

Location ...............................................................................................................................5-11

How It Works ........................................................................................................................ 5-11

Testing ..................................................................................................................................5-12

Fuel Sender ................................................................................................................................5-12

Purpose ................................................................................................................................5-12

Location ...............................................................................................................................5-12

How It Works ........................................................................................................................5-12

Testing ..................................................................................................................................5-13

Alarm, Low Engine Oil ................................................................................................................5-13

Purpose ................................................................................................................................5-13

Location ...............................................................................................................................5-13

How It Works ........................................................................................................................5-13

Testing ..................................................................................................................................5-13

Fuses ..........................................................................................................................................5-14

Purpose ................................................................................................................................5-14

Location ...............................................................................................................................5-14

How It Works ........................................................................................................................5-14

Testing ..................................................................................................................................5-14

Fusible Link ................................................................................................................................5-14

Purpose ................................................................................................................................5-14

Location ...............................................................................................................................5-14

How It Works ........................................................................................................................5-15

Testing ..................................................................................................................................5-15

Glow Plug ...................................................................................................................................5-16

Purpose ................................................................................................................................5-16

Location ...............................................................................................................................5-16

How It Works ........................................................................................................................5-16

Testing ..................................................................................................................................5-16

Battery ........................................................................................................................................5-17

Purpose ................................................................................................................................5-17

Location ...............................................................................................................................5-17

How It Works ........................................................................................................................5-17

Testing ..................................................................................................................................5-17

Storage ................................................................................................................................5-18

Alternator ....................................................................................................................................5-18

Purpose ................................................................................................................................5-18

Location ...............................................................................................................................5-18

How It Works ........................................................................................................................5-18

Testing ..................................................................................................................................5-18

Starter .........................................................................................................................................5-19

Purpose ................................................................................................................................5-19

Location ...............................................................................................................................5-19

How It Works ........................................................................................................................5-19

Testing ..................................................................................................................................5-19

viiTX525 Service Manual Rev. 000

TABLE OF CONTENTS

HYDRAULIC SYSTEM

2 Spool Loader Valve Replacement .............................................................................................6-1

2 Spool Loader Valve Removal ..............................................................................................6-1

2 Spool Loader Valve Installation ...........................................................................................6-5

Auxiliary Valve Replacement ........................................................................................................6-9

Auxiliary Valve Removal.........................................................................................................6-9

Auxiliary Valve Installation....................................................................................................6-14

Tandem Pump / Engine Coupling Assembly Replacement ........................................................6-19

Coupling Removal ................................................................................................................6-19

Coupling Installation .............................................................................................................6-20

Hydraulic Oil Filter Head Replacement ......................................................................................6-22

Hydraulic Oil Filter Head Removal .......................................................................................6-22

Hydraulic Oil Filter Head Installation ....................................................................................6-25

Hydraulic Tandem Pump Replacement ......................................................................................6-30

Hydraulic Tandem Pump Removal .......................................................................................6-30

Hydraulic Tandem Pump Installation ....................................................................................6-37

Hydraulic Tandem Pump Rebuild ...............................................................................................6-42

6 gpm Pump Disassembly ...................................................................................................6-44

14 gpm Pump Disassembly .................................................................................................6-45

14 gpm Pump Assembly ......................................................................................................6-48

6 gpm Pump Assembly ........................................................................................................6-51

Hydraulic Tandem Pump Assembly......................................................................................6-54

Auxiliary Valve Rebuild ...............................................................................................................6-57

Auxiliary Valve ......................................................................................................................6-57

Relief Assembly ...................................................................................................................6-64

Spool Assembly ...................................................................................................................6-64

Auxiliary Valve Assembly .....................................................................................................6-64

Loader Valve Rebuild .................................................................................................................6-72

Joystick Assembly Installation ..............................................................................................6-74

Spool Removal .....................................................................................................................6-77

Spool Assembly ...................................................................................................................6-83

Main Relief Valve .................................................................................................................6-90

Work Port Relief ...................................................................................................................6-92

Lift Cylinder Assembly Rebuild ...................................................................................................6-94

Lift Cylinder Disassembly .....................................................................................................6-96

Lift Cylinder Assembly ........................................................................................................6-101

Tilt Cylinder Assembly Rebuild .................................................................................................6-103

Tilt Cylinder Disassembly ...................................................................................................6-106

Tilt Cylinder Assembly ........................................................................................................ 6-112

DRIVE SYSTEM

Lifting the Machine for Service .....................................................................................................7-1

Track Guide Alignment .................................................................................................................7-3

Belt Replacement .........................................................................................................................7-5

Belt Removal ..........................................................................................................................7-5

Belt Installation .......................................................................................................................7-8

Idler Arm Replacement ...............................................................................................................7-12

Idler Arm Removal ...............................................................................................................7-12

Idler Arm Assembly Installation ............................................................................................7-15

Right Hydrostatic Pump Replacement........................................................................................7-18

Right Hydrostatic Pump Removal ........................................................................................7-18

Right Hydrostatic Pump Installation .....................................................................................7-29

viii Rev. 000 TX525 Service Manual

TABLE OF CONTENTS

DRIVE SYSTEM cont.

Left Hydrostatic Pump Replacement ..........................................................................................7-39

Left Hydrostatic Pump Removal ..........................................................................................7-39

Left Hydrostatic Pump Installation .......................................................................................7-48

Wheel Motor Replacement .........................................................................................................7-56

Wheel Motor Removal .........................................................................................................7-56

Wheel Motor Installation ......................................................................................................7-62

Track Replacement ....................................................................................................................7-68

Wide Track Removal ............................................................................................................7-68

Wide Track Installation .........................................................................................................7-70

Narrow Track Removal ........................................................................................................7-72

Narrow Track Installation .....................................................................................................7-73

Track Guide Replacement ..........................................................................................................7-75

Track Guide Removal ..........................................................................................................7-75

Track Guide Installation .......................................................................................................7-76

Road Wheel Replacement..........................................................................................................7-77

Road Wheel Removal ..........................................................................................................7-77

Road Wheel Rebuild ............................................................................................................7-79

Road Wheel Installation .......................................................................................................7-80

Tensioner Arm Replacement - Wide Track .................................................................................7-82

Tensioner Arm Removal - Wide Track ..................................................................................7-82

Tensioner Arm Rebuild - Wide Track ....................................................................................7-83

Tensioner Arm Installation - Wide Track ...............................................................................7-87

Tensioner Arm Wheel Bearing Replacement - Wide Track.........................................................7-90

Tensioner Arm Wheel Bearing Removal - Wide Track .........................................................7-90

Tensioner Arm Wheel Bearing Installation - Wide Track ......................................................7-94

Tensioner Wheel Bearing Replacement - Narrow Track.............................................................7-97

Tensioner Wheel Bearing Removal - Narrow Track .............................................................7-97

Tensioner Wheel Bearing Installation - Narrow Track ..........................................................7-99

BRAKE ASSEMBLY

Parking Brake Assembly Replacement ........................................................................................8-1

Brake Assembly Removal 270000100 - 270000999 ..............................................................8-1

Brake Cable Replacement 270000100 - 270000999 ............................................................8-7

Brake Assembly Installation 270000100 - 270000999 ......................................................... 8-11

Brake Assembly Removal 280000100 & higher ...................................................................8-18

Brake Cable Replacement 280000100 & higher ..................................................................8-24

Brake Assembly Installation 280000100 & higher ................................................................8-26

Brake Plate Replacement 280000100 & higher .........................................................................8-32

Brake Plate Removal ...........................................................................................................8-32

Brake Plate Installation ........................................................................................................8-36

Brake Handle Spring Bracket Assembly Replacement 280000100 & higher .............................8-40

Brake Handle Spring Bracket Assembly Removal ...............................................................8-40

Brake Handle Spring Bracket Assembly Installation ............................................................8-43

Brake Handle Replacement........................................................................................................8-48

Brake Handle Removal ........................................................................................................8-48

Brake Handle Installation .....................................................................................................8-51

ixTX525 Service Manual Rev. 000

TABLE OF CONTENTS

HYDRAULIC TESTING

TX525 ...........................................................................................................................................9-1

Introduction ............................................................................................................................9-1

Flow Testing ...........................................................................................................................9-1

Hydraulic Testing ..........................................................................................................................9-3

Hydrostatic Testing Procedures ....................................................................................................9-3

Auxiliary Circuit Pressure Test ...............................................................................................9-4

Removal of Pressure Gauge ..................................................................................................9-5

Auxiliary Circuit Flow Test ......................................................................................................9-7

Auxiliary Flow Testing.............................................................................................................9-7

Troubleshooting .....................................................................................................................9-7

Flow Meter Removal ..............................................................................................................9-7

Loader Circuit Flow Testing ....................................................................................................9-8

Loader Circuit Pressure Test ................................................................................................9-12

Traction Control Tracking Adjustment, Full Forward Position ..............................................9-17

Traction Control Neutral Adjustment ....................................................................................9-18

Purging Air Procedure ..........................................................................................................9-19

x Rev. 000 TX525 Service Manual

TABLE OF CONTENTS

THIS PAGE INTENTIONALLY LEFT BLANK.

1-1TX525 Service Manual Rev. 000

Avoid res and explosions...

Avoid spilling fuel and never smoke while working with

any type of fuel or lubricant. Wipe up any spilled fuel

or oil immediately. Never remove the fuel cap or add

fuel when the engine is running. Always use approved,

labeled containers for storing or transporting fuel and

lubricants.

Avoid asphyxiation...

Never operate an engine in a conned area without

proper ventilation.

Avoid injury from batteries...

Battery acid is poisonous and can cause burns. Avoid

contact with skin, eyes, and clothing. Battery gases can

explode. Keep cigarettes, sparks, and ames away from

the battery.

Avoid injury due to inferior parts...

Use only original equipment parts to ensure that

important safety criteria are met.

Avoid injury to bystanders...

Always clear the area of bystanders before starting or

testing powered equipment.

Avoid injury due to projectiles...

Always clear the area of sticks, rocks, or any other

debris that could be picked up and thrown by the

powered equipment.

Avoid modications...

Never alter or modify any part unless it is a factory

approved procedure.

Avoid unsafe operation...

Always test the safety interlock system after making

adjustments or repairs on the machine. Refer to the

Electrical section in this manual for more information.

Avoid unexpected starting of engine...

Always turn off the engine and disconnect the spark plug

wire(s) before cleaning, adjusting, or repair.

Avoid lacerations and amputations...

Stay clear of all moving parts whenever the engine is

running. Treat all normally moving parts as if they were

moving whenever the engine is running or has the

potential to start.

Avoid burns...

Do not touch the engine, mufer, or other components

which may increase in temperature during operation,

while the unit is running or shortly after it has been

running.

This symbol means WARNING or

PERSONAL SAFETY INSTRUCTION -

read the instruction because it has to do

with your safety. Failure to comply with

the instruction may result in personal

injury or even death.

This manual is intended as a service

and repair manual only. The safety instructions provided

herein are for troubleshooting, service, and repair of the

Sitework Systems TX525 compact utility loader.

The TX525 loader and attachment operator’s manual

contain safety information and operating tips for safe

operating practices. Operator’s manuals are available on

line at www.toro.com or:

The Toro Company

Publications Department

8111 Lyndale Avenue South

Bloomington, MN 55420

SAFETY INFORMATION

General Information

Think Safety First

SAFETY INFORMATION

1

General Information

This symbol means WARNING or

PERSONAL SAFETY INSTRUCTION

- read the instruction because it has to

do with your safety. Failure to comply

with the instruction may result in

personal injury or even death.

This manual is intended as a service and repair

manual only. The safety instructions provided herein

are for troubleshooting, service, and repair of the

Sitework Systems TX 413 compact utility loader.

The TX 413 loader and attachment operator’s

manuals contain safety information and operating tips

for safe operating practices. Operator’s manuals are

available through your Toro parts source or:

The Toro Company

Publications Department

8111 Lyndale Avenue South

Bloomington, MN 55420

Think Safety First

Avoid unexpected starting of engine...

Always turn off the engine and disconnect the spark

plug wire(s) before cleaning, adjusting, or repair.

Avoid lacerations and amputations...

Stay clear of all moving parts whenever the engine is

running. Treat all normally moving parts as if they were

moving whenever the engine is running or has the

potential to start.

Avoid burns...

Do not touch the engine, muffler, or other components

which may increase in temperature during operation,

while the unit is running or shortly after it has been

running.

Avoid fires and explosions...

Avoid spilling fuel and never smoke while working with

any type of fuel or lubricant. Wipe up any spilled fuel or

oil immediately. Never remove the fuel cap or add fuel

when the engine is running. Always use approved,

labeled containers for storing or transporting fuel and

lubricants.

Avoid asphyxiation...

Never operate an engine in a confined area without

proper ventilation.

Avoid injury from batteries...

Battery acid is poisonous and can cause burns. Avoid

contact with skin, eyes, and clothing. Battery gases

can explode. Keep cigarettes, sparks, and flames away

from the battery.

Avoid injury due to inferior parts...

Use only original equipment parts to ensure that

important safety criteria are met.

Avoid injury to bystanders...

Always clear the area of bystanders before starting or

testing powered equipment.

Avoid injury due to projectiles...

Always clear the area of sticks, rocks, or any other

debris that could be picked up and thrown by the

powered equipment.

Avoid modifications...

Never alter or modify any part unless it is a factory

approved procedure.

Avoid unsafe operation...

Always test the safety interlock system after making

adjustments or repairs on the machine. Refer to the

Electrical section in this manual for more information.

1-2 Rev. 000 TX525 Service Manual

SAFETY INFORMATION

Hydraulics Safety

• Inspect all hydraulic line connectors and ttings. Make

sure all hydraulic hoses and lines are in good condition

before applying pressure to the system.

• Keep body and hands away from pin hole leaks or

nozzles that eject high pressure hydraulic uid. Use

cardboard or paper to nd hydraulic leaks. Hydraulic

uid escaping under pressure can penetrate the skin

and cause injury. Fluid accidentally injected into the

skin must be surgically removed within a few hours by a

doctor or gangrene may occur.

• Before disconnecting or performing any work on the

hydraulic system, lower the loader arm/attachment to the

ground and stop the engine so all pressure is relieved.

• Be sure you understand a service procedure before

working on the machine.

2-1TX525 Service Manual Rev. 000

SPECIFICATIONS

General Specications

Item Specication

Engine Domestic:

22319 Ser #270000001 - 280999999 / D902E2B

22320 Ser #270000001 - 280999999 / D902E2B

International:

22333 Ser #270000001 - 280999999 / D902E2B

22334 Ser #270000001 - 280999999 / D902E2B

RPM Setting Domestic:

No-load Speed – 3670 rpm +20/-50 rpm

Low idle Speed – 1600 rpm ± 100 rpm

International:

No-load Speed – 3200 rpm +75/-50 rpm

Low idle Speed – 1600 rpm ± 50 rpm

Oil Capacity 3.84 quarts (3.63 liters) with lter

Fuel Tank 6 gallons (22.7 liters)

TX525 Narrow Track TX525 Wide Track

Overall Length, without Bucket 70.7” (179.6cm) 70.7” (179.6cm)

Overall Length, with Bucket 92” (233.7cm) 92” (233.7cm)

Overall Width 33.7” (85.6cm) 41” (104.1cm)

Overall Height 46.1” (117.1cm) 46.1” (117.1cm)

Overall Operating Height, Fully Raised 90.1” (228.9cm) 90.1” (228.9cm)

Reach, Fully Raised 21.8” (55.4cm) 21.8” (55.4cm)

Reach Maximum 37” (94cm) 37” (94cm)

Dump Angle 38º 38º

Dump Height 46.1” (117.1cm) 46.1” (117.1cm)

Bucket Rollback, Ground Position 23º 23º

Bucket Rollback, Carry Position 23º 23º

Bucket Rollback, Fully Raised 85º 85º

Wheel Base 31.1” (79cm) 31.1” (79cm)

Ground Clearance Maximum 4.6” (11.7cm) 4.6” (11.7cm)

Dimensions

2-2 Rev. 000 TX525 Service Manual

SPECIFICATIONS

Periodic Maintenance Items

Item Specication Maintenance Interval

Grease General purpose grease 8 hours

Hydraulic Oil 10w-30 or 15w-40 API service CH4 or

higher diesel engine oil

400 hours*

Hydraulic Filter Toro OEM lter 8 hours initial, 200 hours thereafter

Engine Oil Toro OEM lter 50 hours initial & 100 hours thereafter*

Engine Primary Air Filter Toro OEM lter 200 hours*

Engine Safety Air Filter Toro OEM lter 600 hours*

Cooling System 50/50 solution of water and ethylene

glycol

8 hours - clean radiator

100 hours - check cooling

system hoses

yearly - change engine coolant

* More often in dusty, dirty conditions.

Performance (Narrow Track)

Item Specication

Tip Capacity 1580 lbs. (716.6kg) (per SAE J732)

Operating Capacity 553 lbs. (250.8kg) (35% of tip per SAE J818)

Speed 0 - 4.5 mph (0 - 7.2km/hr) forward

0 - 2 mph (0 - 3.2km/hr) reverse

Weight 1904 lbs. (863.6kg) (traction unit only)

2024 lbs. (918kg) (w/TX bucket)

Performance (Wide Track)

Item Specication

Tip Capacity 1580 lbs. (716.6kg) (per SAE J732)

Operating Capacity 553 lbs. (250.8kg) (35% of tip per SAE J818)

Speed 0 - 4.5 mph (0 - 7.2km/hr) forward

0 - 2 mph (0 - 3.2km/hr) reverse

Weight 2001 lbs. (907.6kg) (traction unit only)

2127 lbs. (964.7kg) (w/TX bucket)

2-3TX525 Service Manual Rev. 000

SPECIFICATIONS

Item Specication

Gear Pump A two-section tandem gear pump powers the loader and auxiliary hydraulic systems.

Section 1 (Auxiliary): 13.8 gpm @ 3600 rpm (52.2 liter/min)

Section 2 (Loader): 6.0 gpm @ 3600 rpm (22.7 liter/min)

Loader Valve A two-spool monoblock valve controls loader functions via a single lever joystick.

Main Relief Setting: 2400 psi (165.5 bar)

Loader Spool: A 4-position spool with closed, raise, lower, and oat positions

controls loader functions.

Tilt Spool: A 3-position spool with 3000 psi (206.8 bar) work port relief controls

the dump/curl cylinder functions.

Auxiliary Valve A single spool valve controls the auxiliary ow to the TX attachments. The valve is actuated

by single-step motion lever for forward and reverse-detent positions.

Main Relief Setting: 3000 psi (206.8 bar)

Hydrostatic Pumps The traction circuit is powered by dual hydrostatic pumps in a closed loop system. The

hydrostatic pumps are belt driven off of the auxiliary drive shaft on the front of the engine.

The circuit charge pressure is supplied by a 5 psi (.34 bar) check valve in the loader pump

return circuit. The pumps have service bypass valves for towing and have shock valves to

limit circuit pressure spikes. The pumps are mechanically actuated by the TX traction control

system.

Pump Displacement: 1.28 in

3

/rev (3.25cm

3

/rev)

Pump Speed: 3050 rpm through pulley reduction @ 3600 engine rpm

Shafts: .669” (1.7cm) diameter tapered shaft with 7/16” (1.1cm)

threaded end

Pulleys: Cast ductile iron “3V” pulleys

Shock Valve Relief: 3000 psi (206.8 bar)

Wheel Motors Two LSHT motors directly drive the track drive wheels.

Displacement: 32.3 in

3

/rev (82cm

3

/rev)

Mounting: Standard wheel mounting

Shaft: 1 3/8” (3.5cm) tapered shaft with 1.125” (2.9cm) threaded end

Lift Cylinders The lift circuit has 2 hydraulic cylinders that control loader height.

Bore Size: 1.75” (4.4cm)

Rod Size: 1.0” (2.5cm)

Stroke: 18.4” (46.7cm)

Working Pressure: 3000 psi (206.8 bar)

Dump Cylinder The Quick-Attach angle is controlled by a single hydraulic cylinder.

Bore Size: 2.75” (7cm)

Rod Size: 1.25” (3.2cm)

Stroke: 7.75” (19.7cm)

Working Pressure: 3000 psi (206.8 bar)

Hydraulic System

2-4 Rev. 000 TX525 Service Manual

SPECIFICATIONS

Electrical System

Hydraulic System cont.

Track System

Item Specication

Battery 12 volt, BCI group 55 battery with 585 CCA

Gauges The control panel contains hour meter, fuel gauge, glow plug control, water temp,

electrical charge and oil pressure.

Fuel System Electric frame mounted pump

Ignition The ignition switch is panel mounted with STOP-RUN-START positions.

Fuses The machine has a fuse block with 2 separate fuses, 10 and 30 amp.

Item Specication

Tank The hydraulic tank is a fabricated weldment integrated into the main frame. The tank has

a cleanout access, stainless screens at the ll and suction ports and a remote breather

connected via hose.

Capacity: 10.5 gallons (39.7 liters)

Filter In addition to the in-tank screens, the loader circuit passes through a 10 micron spin-on lter

prior to returning to tank.

Item Specication

Track The tracks are Kevlar reinforced, endless rubber rings with 28 internal drive lugs. The outer

tread on the tracks is a turf-friendly S-shaped pattern with pitched crosscuts.

Track Width: TX525 (Narrow Track) - 5.88” (14.9cm)

TX525 (Wide Track) - 9.5” (24.13cm)

Track Pitch: 3.45” (8.8cm)

Drive Wheel The drive wheels are single-piece, austempered ductile iron, squirrel cage castings. The

wheels are mounted directly onto the tapered shafts of the wheel motors.

Wheel Diameter: 11.63” (29.5cm)

No. of Teeth:eter 11

Road Wheels Constant track ground pressure is maintained by 20 ductile iron road wheels. The road

wheels each have a sealed bearing that are protected by a secondary dirt seal on the inside

and a gasketed steel cap on the outside.

2-5TX525 Service Manual Rev. 000

SPECIFICATIONS

2 - 4 TimeCutter

®

Z Service Manual

Torque Specifications

Recommended fastener torque values are listed in the

following tables. For critical applications, as

determined by Toro, either the recommended torque or

a torque that is unique to the application is clearly

identified and specified in the service manual.

These torque specifications for the installation and

tightening of fasteners shall apply to all fasteners which

do not have a specific requirement identified in the

service manual. The following factors shall be

considered when applying torque: cleanliness of the

fastener, use of a thread sealant (Loctite), degree of

lubrication on the fastener, presence of a prevailing

torque feature, hardness of the surface underneath of

the fastener’s head, or similar condition which affects

the installation.

As noted in the following tables, torque values should

be reduced by 25% for lubricated fasteners to

achieve the similar stress as a dry fastener. Torque

values may also have to be reduced when the fastener

is threaded into aluminum or brass. The specific

torque value should be determined based on the

aluminum or brass material strength, fastener size,

length of thread engagement, etc.

The standard method of verifying torque shall be

performed by marking a line on the fastener (head or

nut) and mating part, then back off fastener 1/4 of a

turn. Measure the torque required to tighten the

fastener until the lines match up.

Fastener Identification

Figure 1

Figure 2

Inch Series Bolts and Screws

(A) Grade 1

(B) Grade 5

(C) Grade 8

Metric Bolts and Screws

(A) Class 8.8 (B) Class 10.9

2

Torque Specications

2-6 Rev. 000 TX525 Service Manual

SPECIFICATIONS

TimeCutter

®

Z Service Manual 2 - 5

Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Inch Series)

Note: Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

oil, graphite, or thread sealant such as Loctite.

Note: Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

Note: The nominal torque values listed above for

Grade 5 and 8 fasteners are based on 75% of the

minimum proof load specified in SAE J429. The

tolerance is approximately

± 10% of the nominal torque

value. Thin height nuts include jam nuts.

Thread Size

Grade 1, 5, &

8 with Thin

Height Nuts

SAE Grade 1 Bolts, Screws,

Studs, & Sems with Regular

Height Nuts (SAE J995

Grade 2 or Stronger Nuts)

SAE Grade 5 Bolts, Screws,

Studs, & Sems with Regular

Height Nuts (SAE J995

Grade 2 or Stronger Nuts)

SAE Grade 8 Bolts, Screws,

Studs, & Sems with Regular

Height Nuts (SAE J995

Grade 2 or Stronger Nuts)

In-lb In-lb N-cm In-lb N-cm In-lb N-cm

# 6 - 32 UNC

10 ± 2 13 ± 2 147 ± 23

15 ± 2 170 ± 20 23 ± 2 260 ± 20

# 6 - 40 UNF 17 ± 2 190 ± 20 25 ± 2 280 ± 20

# 8 - 32 UNC

13 ± 2 25 ± 5 282 ± 30

29 ± 3 330 ± 30 41 ± 4 460 ± 45

# 8 - 36 UNF 31 ± 3 350 ± 30 43 ± 4 31 ± 3

# 10 - 24 UNC

18 ± 2 30 ± 5 339 ± 56

42 ± 4 475 ± 45 60 ± 6 674 ± 70

#10 - 32 UNF 48 ± 4 540 ± 45 68 ± 6 765 ± 70

1/4 - 20 UNC 48 ± 7 53 ± 7 599 ± 79 100 ± 10 1125 ± 100 140 ± 15 1580 ± 170

1/4 - 28 UNF 53 ± 7 65 ± 10 734 ± 113 115 ± 10 1300 ± 100 160 ± 15 1800 ± 170

5/16 - 18 UNC 115 ± 15 105 ± 17 1186 ± 169 200 ± 25 2250 ± 280 300 ± 30 3390 ± 340

5/16 - 24 UNF 138 ± 17 128 ± 17 1446 ± 192 225 ± 25 2540 ± 280 325 ± 30 3670 ± 340

ft-lb ft-lb N-m ft-lb N-m ft-lb N-m

3/8 - 16 UNC 16 ± 2 16 ± 2 22 ± 3 30 ± 3 41 ± 4 43 ± 4 58 ± 5

3/8 - 24 UNF 17 ± 2 18 ± 2 24 ± 3 35 ± 3 47 ± 4 50 ± 4 68 ± 5

7/16 - 14 UNC 27 ± 3 27 ± 3 37 ± 4 50 ± 5 68 ± 7 70 ± 7 68 ± 9

7/16 - 20 UNF 29 ± 3 29 ± 3 39 ± 4 55 ± 5 75 ± 7 77 ± 7 104 ± 9

1/2 - 13 UNC 30 ± 3 48 ± 7 65 ± 9 75 ± 8 102 ± 11 105 ± 10 142 ± 14

1/2 - 20 UNF 32 ± 3 53 ± 7 72 ± 9 85 ± 8 115 ± 11 120 ± 10 163 ± 14

5/8 - 11 UNC 65 ± 10 88 ± 12 119 ± 16 150 ± 15 203 ± 20 210 ± 20 285 ± 27

5/8 - 18 UNF 75 ± 10 95 ± 15 129 ± 20 170 ± 15 230 ± 20 240 ± 20 325 ± 27

3/4 - 10 UNC 93 ± 12 140 ± 20 190 ± 27 265 ± 25 359 ± 34 374 ± 35 508 ± 47

3/4 - 16 UNF 115 ± 15 165 ± 25 224 ± 34 300 ± 25 407 ± 34 420 ± 35 569 ± 47

7/8 - 9 UNC 140 ± 20 225 ± 25 305 ± 34 430 ± 45 583 ± 61 600 ± 60 813 ± 81

7/8 - 14 UNF 155 ± 25 260 ± 30 353 ± 41 475 ± 45 644 ± 61 660 ± 60 895 ± 81

Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Inch Series)

2-7TX525 Service Manual Rev. 000

SPECIFICATIONS

2 - 6 TimeCutter

®

Z Service Manual

Standard Torque for Dry, Zinc, and Steel Fasteners (Metric Fasteners)

Note: Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

oil, graphite, or thread sealant such as Loctite.

Note: Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

Note: The nominal torque values listed above are

based on 75% of the minimum proof load specified in

SAE J1199. The tolerance is approximately

± 10% of

the nominal torque value. Thin height nuts include jam nuts.

Thread Size

Class 8.8 Bolts, Screws, and Studs with

Regular Height Nuts

(Class 8 or Strong Nuts)

Class 10.9 Bolts, Screws, and Studs with

Regular Height Nuts (

Class 10 or Strong Nuts)

M5 X 0.8 57 ± 5 in-lb 640 ± 60 N-cm 78 ± 7 in-lb 885 ± 80 N-cm

M6 X 1.0 96 ± 9 in-lb 1018 ± 100 N-cm 133 ± 13 in-lb 1500 ± 150 N-cm

M8 X 1.25 19 ± 2 ft-lb 26 ± 3 N-m 27 ± 2 ft-lb 36 ± 3 N-m

M10 X 1.5 38 ± 4 ft-lb 52 ± 5 N-m 53 ± 5 ft-lb 72 ± 7 N-m

M12 X 1.75 66 ± 7 ft-lb 90 ± 10 N-m 92 ± 9 ft-lb 125 ± 12 N-m

M16 X 2.0 166 ± 15 ft-lb 225 ± 20 N-m 229 ± 22 ft-lb 310 ± 30 N-m

M20 X 2.5 325 ± 33 ft-lb 440 ± 45 N-m 450 ± 37 ft-lb 610 ± 50 N-m

Standard Torque for Dry, Zinc and Steel Fasteners (Metric Series)

Page is loading ...

Toro TX 525 Wide Track Compact Utility Loader User manual

This manual is also suitable for

Toro TX 525 Wide Track Compact Utility Loader User manual

Related papers

Other documents