Digimerge DBD34TL Quick start guide

Digimerge
Brand
Digimerge
Model
DBD34TL
Category
Security camera accessories
Type
Quick start guide
Product Information
User Manuals
Quick Start Guides
Specification Sheets
WARNING - A REGULATED UL / CSA APPROVED 12V DC power
supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.
Video Tutorials & DemosLatest News
3 x Drywall Anchors
Contents
ATTENTION - This camera includes an Auto Mechanical IR Cut Filter.
When the camera changes between Day/Night viewing modes, an
audible clicking noise may be heard from the camera. This clicking is
normal, and indicates that the camera filter is working.
700TVL VARIFOCAL
IR DOME CAMERA
MODEL: DBD34TL
QUICK START GUIDE
English Version 1.0
www.flirsecurity.com/pro
IT’S ALL ON THE WEB!
www.flirsecurity.com/pro
VISIT
FLIR Systems, Inc.
Copyright © 2014
As our products are subject to continuous improvement, FLIR Systems,
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE
1 x Indoor IR Dome
Camera with Varifocal Lens
Features
Safety Precautions
• This camera is for indoor use only.
• Use an appropriate low voltage power cable to prevent fire or
electrical shock.
• Make sure to install the camera in an area that can support
the camera weight.
• There are no user serviceable parts inside the camera. Please
do not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material.
Please use a soft cloth to clean the lens cover.
• 700 TVL Resolution, 1/3” 960H Image Sensor
• True Day / Night with Mechanical ICR
• 2.8-12mm Varifocal Lens
• 65ft (20m) IR Night Vision*
• 3 Axis Design for Wall / Ceiling Mount
• 12V DC Operation
* IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on
the camera application
3 x Mounting Screws
1 x Dome Cover Key
Installing the Camera
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the camera(s) and
cables to the DVR.
Image Sensor 1/3” 960H Image Sensor
Video Format NTSC
Effective Pixels H: 960 V: 480
Horizontal Resolution 700 TVL
Scan System 2:1 Interlace
Sync System Internal
S / N Ratio 48dB (AGC Off)
Iris AES
AES Shutter Speed 1/60 ~ 1/25,000 sec.
Min. Illumination 0.3 Lux without IR LED
0 Lux with IR LED
Video Output Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type 2.8–12mm F2.0 / Varifocal
FOV (Diagonal) 28° ~ 94°
Termination Video: BNC Female
IR Range / Qty. 65ft / 20m; 17 IR LED’s
Power Requirement 12V DC ± 10%
Power Consumption 12V: 265mA MAX with IR LED
Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C
Environmental Rating Indoor Only
Dimensions Diameter: 5.0” (128mm)
Height: 3.6” (91mm)
Weight (including stand) 0.6lbs / 0.3kg
Dimensions
Camera Specifications
Setting up the Camera
1. Connect the BNC connector of the camera to the
video cable.
2. DC Power—Power Adapter: Connect a 12V DC
Power Adapter (not included) to the camera. Plug
the Power Adapter into a local power outlet.
• DC Power—Power Pigtail (not included): Connect
a Power Pigtail to the camera. Connect the
terminating wires of the cable directly to the DC
power source.
NOTE: For pigtail connection with 12V DC, make sure to
check polarity specifications on the power adapter.
1. Use the included Dome Cover Key or your finger
to push in the button on the camera base while
pulling the dome cover up.
2. Locate the white latch on camera base (near LOCK
and UNLOCK labels). Push the latch outward and
hold in place.
128mm / 5.0”
91mm /
3.6”
Press to
open housing
3. Twist the black back plate
counterclockwise to
detach it from the camera.
Release the latch.
4. OPTIONAL: Punch out the disc
in the centre of the black back
plate to run cables through
the mounting surface.
5. Mark the position of the 3
holes in the black back plate.
Drill holes where marked.
6. OPTIONAL: Insert drywall anchors as needed.
7. Use the included screws to attach the black back
plate to the mounting surface. Make sure the
CAMERA FRONT label points away from the
mounting surface.
8. Place the camera base over the black back plate
and turn counterclockwise to lock in place.
Push
outward
Punch out and
run cables
through here
ZOOM
FOCUS
9. Use a flat-head screwdriver to slightly loosen the
ZOOM and FOCUS knobs. Move knobs left and
right to adjust zoom and focus. Tighten knobs when
finished.
10. Adjust the position of the camera by rotating the
black camera module (rotates 360° before it is
stopped).
11. Use a Philips screwdriver to loosen the screws on
either side of the camera module. Tilt the top of the
module to adjust the viewing angle. Tighten screws
when finished.
12. Replace the dome cover so the arrow on the dome
cover points toward the button on the camera base.
Loosen screws
on both sides
to tilt
NOTE: Make sure IR
LED’s are clear from
camera housing when
installed. If IR LED’s are
blocked, nighttime image
may appear cloudy.
  • Page 1 1
  • Page 2 2

Digimerge DBD34TL Quick start guide

Digimerge
Brand
Digimerge
Model
DBD34TL
Category
Security camera accessories
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents