Digimerge DBD34TL Quick start guide

Brand: Digimerge

Model: DBD34TL

Type: Quick start guide

WARNING - A REGULATED 12V DC power supply is REQUIRED for use

with this camera. Use of a non-regulated, non-conforming power supply

can damage this product and voids the warranty.

3 x Drywall Anchors

Contents

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter.

When the camera changes between Day/Night viewing modes, an

audible clicking noise may be heard from the camera. This clicking is

normal, and indicates that the camera filter is working.

700TVL VARIFOCAL

IR DOME CAMERA

MODEL: DBD34TLP

QUICK START GUIDE

English Version 1.0

flir.com/security/support

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Video Tutorials & DemosLatest News

IT’S ALL ON THE WEB!

flir.com/security/support

VISIT

FLIR Systems, Inc.

As our products are subject to continuous improvement, FLIR Systems,

Inc. reserves the right to modify product design, specifications and

prices, without notice and without incurring any obligation. E&OE

1 x Indoor IR Dome

Camera with Varifocal Lens

Features

Safety Precautions

• This camera is for indoor use only.

• Use an appropriate low voltage power cable to prevent fire or

electrical shock.

• Make sure to install the camera in an area that can support

the camera weight.

• There are no user serviceable parts inside the camera. Please

do not disassemble the camera.

• Do not clean the lens cover with an abrasive cleaning material.

Please use a soft cloth to clean the lens cover.

• 700 TVL Resolution, 1/3” 960H Image Sensor

• True Day / Night with Mechanical ICR

• 2.8-12mm Varifocal Lens

• 65ft (20m) IR Night Vision*

• 3 Axis Design for Wall / Ceiling Mount

• 12V DC Operation

* IR Illumination range under ideal conditions. Objects at or beyond

this range may be partially or completely obscured, depending on

the camera application

3 x Mounting Screws

1 x Dome Cover Key

Installing the Camera

ATTENTION - Test the camera prior to selecting a permanent

mounting location by temporarily connecting the camera(s) and

cables to the DVR.

Image Sensor 1/3” 960H Image Sensor

Video Format PAL

Effective Pixels H: 960 V: 480

Horizontal Resolution 700 TVL

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio 48dB (AGC Off)

Iris AES

AES Shutter Speed 1/50 ~ 1/25,000 sec.

Min. Illumination 0.3 Lux without IR LED

0 Lux with IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens Focal Length / Type 2.8–12mm F2.0 / Varifocal

FOV (Diagonal) 28° ~ 94°

Termination Video: BNC Female

IR Range / Qty. 65ft / 20m; 17 IR LED’s

Power Requirement 12V DC ± 10%

Power Consumption 12V: 265mA MAX with IR LED

Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C

Environmental Rating Indoor Only

Dimensions Diameter: 5.0” (128mm)

Height: 3.6” (91mm)

Weight (including stand) 0.6lbs / 0.3kg

Dimensions

Camera Specifications

Setting up the Camera

1. Connect the BNC connector of the camera to the

video cable.

2. DC Power—Power Adapter: Connect a 12V DC

Power Adapter (not included) to the camera. Plug

the Power Adapter into a local power outlet.

• DC Power—Power Pigtail (not included): Connect

a Power Pigtail to the camera. Connect the

terminating wires of the cable directly to the DC

power source.

NOTE: For pigtail connection with 12V DC, make sure to

check polarity specifications on the power adapter.

1. Use the included Dome Cover Key or your finger

to push in the button on the camera base while

pulling the dome cover up.

2. Locate the white latch on camera base (near LOCK

and UNLOCK labels). Push the latch outward and

hold in place.

128mm / 5.0”

91mm /

3.6”

Press to

open housing

3. Twist the black back plate

counterclockwise to

detach it from the camera.

Release the latch.

4. OPTIONAL: Punch out the disc

in the centre of the black back

plate to run cables through

the mounting surface.

5. Mark the position of the 3

holes in the black back plate.

Drill holes where marked.

6. OPTIONAL: Insert drywall anchors as needed.

7. Use the included screws to attach the black back

plate to the mounting surface. Make sure the

CAMERA FRONT label points away from the

mounting surface.

8. Place the camera base over the black back plate

and turn counterclockwise to lock in place.

Push

outward

Punch out and

run cables

through here

ZOOM

FOCUS

9. Use a flat-head screwdriver to slightly loosen the

ZOOM and FOCUS knobs. Move knobs left and

right to adjust zoom and focus. Tighten knobs when

finished.

10. Adjust the position of the camera by rotating the

black camera module (rotates 360° before it is

stopped).

11. Use a Philips screwdriver to loosen the screws on

either side of the camera module. Tilt the top of the

module to adjust the viewing angle. Tighten screws

when finished.

12. Replace the dome cover so the arrow on the dome

cover points toward the button on the camera base.

Loosen screws

on both sides

to tilt

NOTE: Make sure IR

LED’s are clear from

camera housing when

installed. If IR LED’s are

blocked, nighttime image

may appear cloudy.

Digimerge DBD34TL Quick start guide

Digimerge DBD34TL Quick start guide

Digimerge DBD34TL Quick start guide

Related papers

Other documents