8
8
8
8
1 P C
1 P C
1
2
5 6 78
1 P C 1 P C
9
20P CS
A
B
C
D
E
F
4P CS
1 0P CS
2P CS
7P CS
1 6P CS
6x35mm
1 5x9.5mm
6x30mm
4x40mm
4x1 0mm
4x12 mm
52x90mm
G2P CS
H12 P CS
1 P C 1 P C
34
2P CS 4P CS
1 0
1 P C 1 P C
1
2
3
4
5
7
7
1 0
6
4x1 2mm
75x73x1 4mm
9
I1 P C
CARE INSTRUCTIONS:
TO BE ASSEMBLED ON A CLEAN, DRY AND SMOOTH SURFACE. WIPE CLEAN WITH A SOFT DAMP CLOTH. NEVER USE SCOURERS, ABRASIVES OR CHEMICAL SOLVENTS. CHECK AND
TIGHTEN ALL PARTS REGULARLY. KEEP AWAY FROM MOISTURE AND DIRECT SUNLIGHT. STORE IN A DRY PLACE. FOR INDOOR USE ONLY.
WARNING!
DO NOT STAND, SIT OR LEAN ON THIS UNIT. DO NOT USE THIS UNIT AS A STEP LADDER. ENSURE THIS UNIT IS USED ONLY ON A FLAT SURFACE.DO NOT USE THIS UNIT UNLESS ALL BOLTS
AND SCREWS ARE FIRMLY SECURED. DO NOT PLACE HOT ITEMS SUCH AS COFFEE CUPS DIRECTLY ON THE SURFACE OF THIS FURNITURE ITEM. KEEP AWAY FROM CHILDREN AND BABIES.
THIS PACKAGE CONTAINS SMALL PARTS AND SHARP POINTS. ADULT ASSEMBLY REQUIRED. A MILD ODOUR MAY BE PRESENT WHEN FIRST OPENING THIS CARTON. SIMPLY ALLOW TO AIR
OUTSIDE AND THIS WILL FADE. MAXIMUM SAFE LOAD: 10KGS FOR TOP PANEL, 5KGS FOR EACH SHELF.
Assembly Instruction
84x16x10mm
1
4
1
5
3
3
C
C
D
C
C
D
C
C
D
4
C
D
C
5
5
5
D
C
C
7
7
1 0
F
I
5
I
Step 1: Attach part I onto board 5 with Part F (as per below diagram).
Ensure Part I is not fixed on the side with the large holes on board 5 .
Step 2: Fix the screws from Part C onto board 10 , and put Part D into
the corresponding position (as per below diagram). Attach board 4 &
5 to board 10 , and then fix the round screws from Part C with a
screwdriver. Ensure all parts align.
Step 3: Fix the screws from Part C onto board 1 , and put Part D
into the corresponding position (as per below diagram). Attach board
3 and the piece from step 2 to board 1 , and then fix the round
screws from Part C with a screwdriver. Ensure all parts align.
Step 4: Slide board 7 into the corresponding position (as per below
diagram). Ensure it is fully fitted in the grooves.
incorrect
side
B
A
AA
BB
B
8
8
8
8
E
E
E
D
D
D
3
4
5
7
7
E
E
E
A
E
9
2
2
Step 5: Fix Part 9 on board 2 with screw E ( as per below diagram)
Step 6: Attach the piece from step 5 onto the piece from step 4 with
screw E.
Step 7: Fix Part B onto board 2 with screw A.
Step 8: Screw the legs (Part 8) into Part B.
G x 2
H x 4
H x 8
6
6
Step 9: Fix Part G on board 6 with screw H.
Step 10: Attach the piece from step 9 to the rest of the unit with
screw H (as per below diagram).
Please note: For part G, there are three ways to adjust the
position of Part G( as per left side diagram) .
Assembly completion diagram
/
