SENZ STL150 VASKEMASKIN Owner's manual

STL150 STL350

Washing Machine

SENZ WASHING MACHINE.

4 - 39

SENZ VASKEMASKIN.

SENZ PESUKONE.

VASKEMASKINE SENZ.

SENZ TV TTMASKIN

注意：这些标识只印在说明书右侧页面

40 - 75

76 - 111

112 - 147

148 - 183

32

Safety Instructions

For your safety,the information in this manual must be

followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, personal injury or

loss of life. Explanation of the symbols:

If the mains power cable is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid a

hazard.

•

The electric shock!

This combination of symbol and signal word indicates

a potentially dangerous situation which may result in

death or serious injuries unless it’s avoided.

Warning!

！

This combination of symbol and signal word indicates

a potentially dangerous situation which may result in

slight or minor injuries.

Note!

This combination of symbol and signal word indicates

a potentially dangerous situation which may result in

slight or minor injuries or damage to property and the

environment.

Caution!

Warning!

！

4

• The new hose-sets supplied with the appliance

be reused.

are to be used and your old hose-sets should not

• Before any maintenance, unplug the appliance

the mains power.from

• Always unplug the machine and turn off the water

supply after use. The max. inlet water pressure, in

pascals. The min. inlet water pressure, in pascals.

• To ensure your safety, the mains power plug must

Check carefully and make sure that your mains

power socket is properly and reliably earthed.

be inserted into an earthed three-pole socket.

• Make sure that the inlet hose and electricity supply

accordance with the manufacturer's instructions

and local safety regulations.

must be connected by a qualified technician in

Risk to children !

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been

given supervision or instruction concerning use

of the appliance in a safe way and understand

the hazards involved. Children shall not play with

the appliance. Cleaning and user maintenance

shall not be made by children without supervision.

8 years and above and persons with reduced

•

• Children of less than 3 years should be supervised

to ensure that they do not play with appliance.

The appliance can be used by children aged from

5

Risk of explosion!

•

Do not wash or dry articles that have been cleaned

in, washed in, soaked in, or dabbed with combustible

or explosive substances( such as wax, oil, paint,

gasoline, degreasers, dry-cleaning solvents,

kerosene, etc.) This may result in fire or explosion.

• This washing machine is for indoor use only.

• It isn't intended to be built-in.

• The openings must not be obstructed by a carpet.

• Washing machine shall not be installed in bathroom

or very wet rooms as well as in rooms with

or caustic gases.explosive

• The washing machine with single inlet valve only

can be connected to the cold water supply. The

product with double inlet valves should be correctly

connected to the hot water and cold water supply.

• Plug must be accessible after installation.

Installing the product!

Caution!

with the appliance.

• Animals and children may climb into the machine.

Check the machine before every operation.

• Kids should be supervised that they do not play

• Remove all packaging and transport bolts before

the appliance. Otherwise, serious damage

may result.

using

6

Risk of damaging appliance!

• Your product is only for home use and is only

for the textiles suitable for a machine

washing.

designed

• Do not climb up and sit on the top cover of the

machine.

• Do not lean against the machine door.

• Cautions during ha ndling the Machine:

1.Transport bolts must be reinstalled to the

a specialized person.machine by

2.The accumulated water must be drained out

machine.of the

3.Handle the machine carefully. Never hold each

part on the machine while lifting. protruded

Machine door can

transport of the machine.

not be used as a handle during

4.This appliance is heavy. Transport with care.

• Do not close the door with excessive forces. If it

is found difficult to close the door, check to see

clothes are put in or distributed well.if the

• It is forbidden to wash carpets.

Operating the appliance!

• Before washing clothes for the first time, the

needs to be operated in one complete product

operational procedure without

any clothes inside.

round of the whole

7

• Make sure that all pockets are emptied. Sharp

items such as coins,brooches,nails,and rigid

may cause serious damages

to this machine.

screws or stones etc.

• Check whether the water inside the drum has

been drained before opening the door. Do not

the door if there is any water visible.open

• Be careful of burning when the product drains

washing water.hot

• Never refill the water by hand during washing.

• After the program is completed, wait for two

minutes before opening the door.

washing.are suitable for machine

Gasoline and alcohol etc. Must not be forbidden.

Only select detergents that used as detergents.

• Flammable and explosive or toxic solvents are

8

Correct Disposal of this product:

This marking indicates that this product should not be

disposed with other household wastes throughout the

EU.To prevent possible harm to the environment or

human health from uncontrolled waste disposal,recycle

it responsibly to promote the sustainable reuse of

material resources.To return your used device, please use

the collection systems or contact the retailer where the

product was purchased. They return and can take this

product for environmental safe recycling.

Accessories

Product Description

Transport

hole plug Supply hose

cold water

Drain hose

(optional )

support

• The product line chart is for reference only, refer to your product as

standard.

Note!

Owner’s

manual

Mains power cable Door

Control panel

Drain hose

Service filter

Drum

Detergent dispenser

9

Installation

Before installing the machine, select a suitable

with the following characteristics:location

1.Rigid, dry, and level surface

2.Avoid direct sunlight

3.Sufficient ventilation

4.Room temperature is above 0 ° C

5.Keep far away from the heat resources such as

coal or gas.

Unpacking the washing machine

1. Remove the cardboard box and styrofoam packing.

2. Lift the washing machine and remove the base packing.

3. Remove the tape securing the mains power cable and drain hose.

4. Remove the inlet hose from the drum.

Make sure

foam is removed with the bottom one together. the small triangle

surface, then remove the small

foam from the unit bottom manually.

If not, lay the unit down with side

Remove transport bolts

•

Stability is important to prevent the product from

wandering!

Make sure that the product does not stand on

the mains power cable.

Warning!

！

•

Packaging material (e.g. Films, Styrofoam) can be

dangerous for children.

There is a risk of suffocation ! Keep all packaging

well away from children.

Warning!

！

•

• product,

You must remove the transport bolts from the backside before using

the product.

You’ll need the transport bolts again if you move the

so make sure you keep them in a safe place.

Warning!

！

w

W> 20mm

Installation area

10

1.Check if the legs are closely attached to the cabinet. If not, turn them

their original positions and tighten the nuts.to

2.Loosen the lock nut then turn the feet until it closely contacts with

the floor.

Levelling the washing machine

• The lock nuts on all four feet must be screwed tightly against the housing.

Connect the inlet pipe as indicated, There are two ways to connect

• To prevent leakage or water damage, follow the instructions in

Do not kink, crush, modify or sever

•

• For the model equipped with a hot valve,connect it to a hot water

supply hose. Energy consumption will decrease tap with hot water

234

1

Raise Lower

Lock nut

foot

Warning!

！

Warning!

！

Take the following steps to remove the bolts:

1.Loosen 4 bolts with a spanner and then

r e move them.

2.Stop the holes with transport hole plugs.

3.Keep the transport bolts properly for future use.

Connect Water Supply Hose

3.Adjust the legs and lock them with a spanner, make sure the machine

is steady.

this chapter!

water inlet hose.

automatically for some program.

the inlet pipe.

11

Drain Hose

• Do not kink or protract the drain hose.

Warning!

！Warning!

！

water supply hose

water Inlet valve

Connect the other end of inlet pipe to the inlet valve at the backside

of product

Tap with threads and

inlet hose

Special tap for washing machine

Loosen clamp

nut and Tighten clamp

bushing, insert

connecting base

Connection

finished

clamp nut

2.Connection between screw tap and inlet hose.

slide bushing

2341

1.Connection between ordinary tap and inlet hose.

four bolts

Press slide

nut

inlet hose into

and fasten the pipe tightly clockwise.

• Position drain hose properly ,otherwise damage might result from

water leakage.

12

Warning!

！

There are two ways to place the end of drain hose:

1.Put it into the water trough. 2.Connect it to the branch drain

the trough.pipe of

•

• If drain hose is too long, do not force it into the washing machine

cause abnormal noises.as it will

Water

trough

Min.60cm

100cm

Max.

Trough

Hose Retainer

Bind

Man.100cm

Min.60cm

Max.100cm

If the machine has a

• drain hose support, install it following the

Note!

When installing the drain hose, fix it properly with a rope.

diagrams below.

Min.60cm

13

Quick Start

“End” on display.

Open tap

Load

Close

drum door

Plug in

3. After Washing

2. Washing

Select

Programme

Select

function or

Start up

• If default is selected, step 2 can be skipped.

Note!

Before washing, make sure it’s installed properly.

Before washing for the first time, operate the machine with one complete

procedure without any clothes, as follows.

•

Add

detergent

Caution!

1. Before Washing

default

Close

machine door

• Detergent needs to be added

in "case I “after selecting

pre-washing for machines

with this function.

• Make sure that the drum flaps

are properly locked.

• All metal hooks must be

properly hooked inside the

rear door flap.

• Check the roller before

each laundry ,it must roll

smoothly.

14

Knot the long strips,

zip or button

• When washing a single garment, it may easily cause alarm due to

unbalance in the machine. Therefore it is suggested to add one or

two more clothes to be washed together so that draining can be

done smoothly.

• Don’t wash clothes stained with kerosene, gasoline, alcohol or other

flammable materials.

• The working condition of the washer should be (0-40)°C. If used

under 0°C, the inlet valve and draining system may be damaged.

If the machine is placed under a condition of 0℃or less, then it

should be transferred to normal ambient temperature to ensure

the water supply hose and drain hose are not frozen before use.

• Check the labels and the explanation of using detergent before

the wash. Use non-foaming or less-foaming detergent suitable

Take out all items

from the pockets

Put small clothes

pillow slip into the

Check the label

Before Each Washing

Turn easy-pilling and

long-pile fabric inside

different textures

Warning!

！

for machine washing properly.

Separate clothes with

out

15

Detergent Dispenser

Pre wash detergent

Main wash detergent

Softener

I I

I

Caution!

• Detergent only needs to be

added in “case I” after selecting

pre-washing for machines with

this function.

Means must ○ 　Means optional

• As for the agglomerated or ropy detergent or additive, before they

are poured into the detergent box, it is suggested to use some water

for dilution to prevent the inlet of the detergent box from becoming

blocked and overflowing while filling with water.

• Choose a suitable type of detergent for the various washing

temperature to get the best washing performance with less water

and energy consumption.

Note!

Pull out the dispenser

Prewash Softener Main wash

• Do not exceed the “MAX”level

mark when filling in detergent,

additives or softener.

Programme

Cotton

Synthetic

Mix

Jeans

Sportswear

Color Care

Baby Care

Drum Clean

20℃

Intensive

Programme

Spin Only

Rinse & Spin

Delicate

Daily Wash 45’

Quick 15’

Cotton ECO

ECO 40-60

Rapid 45’

Wool

16

On/Off

Product is switched On/Off.

Start/Pause

Press the button to start or

pause the washing cycle.

Programmes

Available according to the

Option

This allows you to select an

light when selected.

Note!

The chart is for reference only, refer to your product as standard.

•

1

3

1

2

4

Display

The display shows the settings, options for your washer. The display

will remain on through the cycle.

5

Control Panel

STL150

Model:

additional function and will laundry type.

A

B

C

D

CD

Door Lock Child Lock

Pre Wash

Extra Rinse

17

On/Off

Product is switched On/Off.

Start/Pause

Press the button to start or

pause the washing cycle.

Programmes

Available according to the

Option

This allows you to select an

light when selected.

Note!

The chart is for reference only, refer to your product as standard.

•

1

3

1

2

4

Display

The display shows the settings, estimated time remaining, options,

and status messages for your washer. The display will remain on

through the cycle.

5

Control Panel

STL350

Model:

additional function and will laundry type.

Door Lock

B

Pre Wash

D

Display

A

Wash Time Delay Time

Error

End

Delay

C

E

Extra Rinse

A

B

CD

E

18

Pre Wash

The Prewash function gives an extra wash before the main wash,

it is suitable for making the dust rise to the surface of the clothes;

You need to put detergent into the Case (I) when you select it.

Option

Caution!

• If there is any break in the power supply while the machine is

operating, a special memory stores the selected programme and

when the power is restarted, the program will continue.

Delay

Set the Delay function:

1.Select a programme;

3.Press [ Start/Pause ] to commence the delay operation

Choose the Programme Start

Setting time

Delay

Cancel the Delay function:

Press the[ Delay ] button until the display shows 0H.It should be

already started, switch off programme to reset a new o ne.

2.Press the Delay button to choose the time

(the delaying time is 0-24 H/3H-6H-9H);

pressed before starting the programme. If the programme ha s

Delay

Pre Wash

Extra Rinse

The Prewash function gives an extra wash before the main wash,

it is suitable for making the dust rise to the surface of the clothes;

You need to put detergent into the Case (I) when you select it.

Extra

Rinse

19

Option

Programme Option Programme Option

Extra

rinse

Cotton

Quick 15’

Rapid 45’

ECO 40-60

Intensive

20°C

Rinse & Spin

Spin Only

Drum Clean

Baby Care

Sportswear

Jeans

Wool

Delicate(F01)

Synthetic

Mix

Pre

wash Pre

wash

Extra

rinse

Delay

○　Means optional

20

Temp.

°C,

Press the button to set the temperature ( C old,20 40°C,60°C,90°C)

Other Functions

Spin

Press the button to change the speed.

1200: 0-600-800-1000-1200 1300: 0-600-800-1000-1300

Programme Default Speed(rpm)

Cotton

Quick 15’

Rapid 45’

ECO 40-60

Intensive

Rinse & Spin

Spin Only

Programme

Drum Clean

Baby Care

Sportswear

Jeans

Wool

Delicate(F01)

Synthetic

Default Speed(rpm)

1200

800

1200 –

800

1000

800

600

1200

Model:STL150 STL350

1200

Temp.

Spin

Child Lock

To avoid mis operation by children.

Start Press [ ] and [Delay]3 sec.

till buzzer beep.

Spin

Choose the

Programme

Spin Delay

20°C

Mix

800

21

Page is loading ...

SENZ STL150 VASKEMASKIN Owner's manual

SENZ STL150 VASKEMASKIN Owner's manual

in other languages

Related papers

Other documents