SKYDANCE T18 User manual

SKYDANCE
Brand
SKYDANCE
Model
T18
Type
User manual
Features
Technical Parameters
MechanicalStructuresandInstallations
Model No.: T18
Touch Glass Panel 0/1-10V Dimmer
1 zone / Touch glass panel / Brightness slide /AC relay output/ Zero-crossing detection / Wireless remote control
● Touch panel 0/1-10V dimmer, output 1 channel 0/1-10V signal.
● Output connect with 0/1-10V dimmable driver.
● High voltage AC input, high voltage AC relay output, with zero-crossing detection.
● Ultra sensitive high strength glass touch panel with touch slide in the middle.
RF 2.4G dimming remote control● Compatibility with .
● Touch keys with LED indicator.
● High-inrush specification relay.
● White & Black glass panel available.
86.00 mm
86.00 mm
52.00 mm
52.00 mm
59.00 mm
33.00 mm
11.50 mm
Typical base as below:
European style 86 size
Installationdiagram:
Baseplate Base
Uninstall Touch panel
AC L input
AC N input
0/1-10V signal output GND
AC N output
AC L output
DIP switch for
0-10V or 1-10V select
LN
+
-
N
L1
AC IN
AC O UT
0/1-10V OUT
Brigh t
Power
20S
Delay Off
ModeBright Brightness,10 levels.
Keyfunction
Power
Mode
20S
Delay O ff
Turn on/off light.
Play dynamic mode, 6 level speed.
Turn off light after 20s.
Input and Output
Operation temperature
Environment
Gross weight
Size
Package
Case temperature (Max.)
IP rating
Ta: -30
O
C ~ +55
O
C
IP20
Tc: +65
O
C
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certication CE,EMC,RED
EN 62368-1:2020+A11:2020
Safety standard
Warranty
5 years
Warranty
Input voltage AC100-240V Touch key + RF 2.4GHz
10m(Barrier-free space)
256 levels
0 -100%
Output signal 0-10V (50mA)
Dimming data
Dimming range
Input signal
RF control distance
Dimming gray level
L112x W112 x H50mm
0.238kg
Output current Max. 3A (AC)
Relay surge current 200A
1
User Manual Ver 1.1.7
60.00 mm
ON 0-10V
1-10V
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
The 0-10V touch panel dimmer can also match with the RF dimming remote (optional).
Use On/Off key Use Power Restart
Match:
Turn on light, turn off, immediately press the On/Off key of the panel for 5s,
then press on/off key (single zone remote) or zone key (multiple zone remote)
of the RF remote within 5s.
The LED indicator fast flash 3 times means match is successful.
Delete:
Turn on light, turn off, immediately press the On/Off key of the panel for 10s to
delete all match,
The LED indicator fast flash 6 times means all matched remotes were deleted.
Match:
Switch off the power, then switch on power, repeat again,
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The LED indicator blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again,
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The LED indicator blinks 5 times means all matched remotes were deleted.
0-10V or 1-10V dimming setting
Select 0-10V dimmer or 1-10V dimmer according to dimmable LED driver.
100
90
80
70
60
50
40
30
20
10
PWMduty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
10.0
9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0-10Vlevel(V)
0-10V Dimmer
100
90
80
70
60
50
40
30
20
10
PWMduty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
10.0
9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
1-10Vlevel(V)
1-10V Dimmer
AC110-220V
V+
V-
DIM+
DIM-
AC N
AC L +Single color LED strip
0/1-10V
Dimmable Driver
Wiring diagram
● Connect with 0/1-10V dimmable driver (no use AC OUT)
LN
+
-
N
L1
AC IN
AC O UT
0/1-10V OUT
● Connect with 0/1-10V dimmable driver (use AC OUT )
AC110-220V
V+
V-
DIM+
DIM-
AC N
AC L
+
0/1-10V
Dimmable Driver Single color LED strip
Note: 1. We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 100 pieces,
The maximum length of the wires from dimmer to LED driver should be no more than 50 meters.
2. The MAX. surge current of the AC OUT is 200A. When connecting multiple capacitive (LED power supplies) or inductive loads,
the sum of the surge currents can not exceed its maximum value. Otherwise, long-term use may cause product damage.
LN
+
-
N
L1
AC IN
AC O UT
0/1-10V OUT
2
User Manual Ver 1.1.7
ON 0-10V
1-10V
ON 0-10V
1-10V
ON 0-10V
1-10V
ON 0-10V
1-10V
  • Page 1 1
  • Page 2 2

SKYDANCE T18 User manual

SKYDANCE
Brand
SKYDANCE
Model
T18
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents