2. SKYDANCE
  3. T18-2
T18-2

SKYDANCE T18-2 User manual

  • Hello! I've reviewed the user manual for the SKY DANCE Dimmer T18-2. This document provides instructions on how to install and operate the rotary glass panel dimmer, which features 1-10V signal output, high voltage AC relay output, and compatibility with RF 2.4G remote controls. I'm ready to answer any questions you might have about it.
  • What type of dimming driver can this device control?
    How do I change the brightness level?
    How do i switch output mode to 0-10V?
    How can I match a remote control?
User Manual Ver 1.1.2
Technical Parameters
Model No.: T18-2
Rotary dimming/Glass panel/AC relay output/Wireless remote control
Features
Page 1
Mechanical Structures and Installations
1-10V Rotary Glass Panel Dimmer
LVD
● Rotary glass panel 1-10V dimmer, 1 channel output.
● Output 1 channel 1-10V signal, connect with 1-10V dimmable driver.
● High voltage AC input, High voltage AC relay output.
● Rotate knob to change brightness, support push and long push operation.
● 256 levels 0-100% dimming smoothly without any flash.
● Compatibility with RF 2.4G single zone or multiple zone dimming remote control.
● White & Black glass panel available.
AC L input
AC N input
Output current Max 1.5A (AC)
Input voltage AC100-240V
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Dimming data
Dimming range
Rotary knob + RF 2.4GHz
10m(Barrier-free space)
256 levels
0 -100%
Input and Output
Warranty
5 years
Warranty
Input signal
RF Control distance
Dimming level
Ta: -30
O
C ~ +55
O
C
T c: +65
O
C
Output signal 1-10V (50mA)
1-10V signal output GND
AC N output
AC L output
● Push: Turn on or off light.
After turn on light:
● Rotate: Rotate knob to adjust brightness, 2.5 turns, 50 levels.
● Long push(1-6s): Continuous 256 levels brightness adjustment.
Knob function
Mechanical Structures and Installations
Typical base as below:
European style
Baseplate Base
Uninstall
Installation diagram:
86 size
Touch panel
86.00 mm
86.00 mm
52.00 mm
52.00 mm
59.00 mm
48.00 mm
11.50 mm
0.5-2.0mm²
4-5mm
Ro HS
T1 8-2
LN
+
-
NL1
AC I N
AC O UT
1-10V OU T
Uin =100-2 40VAC
Out =1-10V (50mA)
AC O ut=Ma x 1.5A
Temp Ra nge: -3 0℃~+55℃
Note: The default output is 1-10V, if you want to 0-10V output, please to turn off light, push the knob
then for 15s , the output will become 0-10V.push the knob immediately
to turn off light, then for 10s , the output will return 1-10V.Push the knob push the knob immediately
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certification CE,EMC,LVD,RED
EN 62368-1:2020+A11:2020
Safety standard(LVD)
www.iskydance.pl
AC110-220V
V+
V-
DIM+
DIM-
ACN
ACL +Single color LED strip
0/1-10V
Dimmable Driver
0.5-2.0mm²
4-5mm
RoHS
T1 8- 2
LN
+
-
NL1
AC IN
AC OU T
1-10 V O UT
Uin =100- 240VAC
Out =1-10 V(50 mA)
AC Ou t=Max 1 .5A
Temp Ra nge: -3 0℃~+55℃
Wiring diagram
● Connect with 1-10V dimming driver (no use AC OUT)
User Manual Ver 1.1.2 Page 2
● Connect with 1-10V dimming driver (use AC OUT)
Match Remote Control (two match ways)
Use Knob
Match:
Turn on light, turn off, immediately push the knob for 5s,
then press on/off key (single zone remote) or zone key
(multiple zone remote) of the RF remote within 5s.
The LED indicator fast flash 3 times
means match is successful.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again,
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
.
Delete:
Switch off the power, then switch on power, repeat again,
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
Delete:
Turn on light, turn off, immediately push the knob for 10s,
The LED indicator fast flash 6 times
means all matched remotes were deleted.
The 1-10V rotary panel dimmer can also match with the RF dimming remote (optional).
End user can choose the suitable match/delete ways. Two options are offered for selection:
● Connect with 1-10V dimming driver (use AC OUT and relay or contactor)
An additional AC relay or contactor is needed when total input current of the load is higher than 1.5A
or inrush current is greater than 15A.
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 100 pieces,
The maximum length of the wires from dimmer to LED driver should be no more than 50 meters.
0.5-2.0mm²
4-5mm
RoHS
T1 8- 2
LN
+
-
NL1
AC IN
AC OU T
1-10 V O UT
Uin =100- 240VAC
Out =1-10 V(50 mA)
AC Ou t=Max 1 .5A
Temp Ra nge: -3 0℃~+55℃
AC110-220V
V+
V-
DIM+
DIM-
ACN
ACL +Single color LED strip
0/1-10V
Dimmable Driver
0.5-2.0mm²
4-5mm
RoHS
T1 8- 2
LN
+
-
NL1
AC IN
AC OU T
1-10 V O UT
Uin =100- 240VAC
Out =1-10 V(50 mA)
AC Ou t=Max 1 .5A
Temp Ra nge: -3 0℃~+55℃
AC110-220V
V+
V-
DIM+
DIM-
ACN
ACL
+Single color LED strip
0/1-10V
Dimmable Driver
Relay or
Contactor
www.iskydance.pl
/