Hobie® Mirage®
Adventure Island Manual
In 1950, Hobie’s dream was born in his parents’
garage when he decided to apply his love
of woodworking to the sport of surfing. Dad
backed out the Buick... Hobie carved out his
very first surfboard...
Hobie’s business of fun had begun.
Table of Contents | 5
hobie.com
The Hobie Island Club is a place to meet other Hobie Mirage Adventure Island
and Hobie Mirage Tandem Island owners to share passions for the waterways and
oceans of our world. Hobie Dealers are organizing local Island Clubs worldwide.
The Hobie Island Club will assist in the introduction of Island owners to one
another where dreams of sailing to places unknown and countless adventures can
become a reality. Go to hobie.com or scan the QR code here to learn more about
joining a club near you.
Anatomy...............................................................................................................6
Assembly.............................................................................................................8
Vantage CT Seating............................................................................................17
MirageDrive
®
......................................................................................................24
On the Water......................................................................................................28
Lowrance
®
Ready Option....................................................................................35
Storage and Transport.......................................................................................38
Maintenance and Care.......................................................................................43
Safety.................................................................................................................45
Warranty............................................................................................................52
Accessories........................................................................................................53
6 | Anatomy
1. Hull
2. Vantage CT Seat
3. MirageDrive 180 with Kick-Up Fins
4. Paddle and T-Handle
5. Lowrance-Ready Components
6. Cassette Plug
7. Akas (4)
8. Aka Carry Bag
9. Mast (2 piece)
10. Sail
11. Batten Set (3 pieces)
12. Small Parts (batten caps, spare sheer pins,
steering handle, screws and steering riser)
6
4
5
3
Items not shown to scale
7
1
2
8
9
10
11
12
Anatomy | 7
hobie.com
Island Terminology
Battens
Battens are long fiberglass
rods that are inserted into the
sail to give it stiffness and help
maintain sail shape.
Amas
Amas are the outer
hulls that provide
stability under sail
power.
Centerboard
The centerboard is used to improve
your upwind performance by
preventing the boat from slipping
sideways in the water.
Roller Furler
The roller furler allows
the sail to be easily rolled
around the mast to reduce
sail size in high winds and
for storage.
Sail
The sail is a “square -top”
design that utilizes the current
trend in sail design for better
performance.
Telltales
Telltales are small ribbons
to help determine the
correct trim of the sail.
Akas
Akas are the aluminum bars that extend
away from the hull to support the amas.
Rudder
The rudder is the
rear blade that is
used to steer the
boat.
Mainsheet
The mainsheet is a rope
that connects to the sail
to control the trim of the
sail.
8 | Assembly Required
Slide the two halves of
the mast together
1
Insert the assembled
mast into the sail sleeve
2
Insert the webbing at the
top of the sail into the mast
cap
3
Feed the downhaul line
through the loop on the
mast collar. Pull tension on
the line to tighten the sail
onto the mast and cleat off
the line. Tie a knot off at
the end for extra security.
4
Mast/ Sail Assembly
Assembly Required | 9
hobie.com
Rotate the mast counterclockwise so that the sail rolls onto the mast per the
diagram below.
7
Slide the batten cap over the ends of the battens and lace the line through the
cap. Make sure to pull tension on the line and cleat it off to hold on the cap and
retain batten pressure into the pocket. Tie off the end of the line for extra batten
security.
6
Feed the battens into the
batten pockets (note they
are different lengths per the
different length pockets)
5
1. PULL
2. CLEAT
10 | Assembly Required
Rudder Installation
Place rudder over rudder
gudgeon and insert pin
Tech Note: A spare rudder
pin is located in the rear
hatch compartment.
1
Place the ring through
the hole in the end of the
rudder pin
2
Lift rudder up/down control
lines and make sure they
are running through the
middle of the rudder pin.
6
Assembly Required | 11
hobie.com
Slide the akas into
the deck mounted
crossbars until they
click into place.
1
Once the akas are inserted, pull out on them to make
sure they are locked in place.
2
Aka Installation
CLICK
To remove the akas,
depress both buttons at
the same time on the
deck mounted crossbar
and slide out the aka.
Aka Removal
12 | Assembly Required
Push in and hold the
diagonal crossbrace end
cap
1
Place end cap over ball
fitting on boat
2
Release end cap and check
to make sure it is locked
onto the boat
3
Diagonal Crossbrace Lock
Assembly Required | 13
hobie.com
Ama Installation
Slide the ama onto the aka
tubes
1
Stretch both Bungee®
cords over the buttons on
the corners of the akas.
2
Steering Handle
Install the handle on the steering post using the small
screw.
OR
1
2
Install the handle on top of the riser and install
with the longer screw.
Your Island comes with two options for
installing the steering handle:
14 | Assembly Required
Insert the mast
through the forward
crossbar bearing and
into the hull until it
goes all the way down
and locks
1
Mast Installation
Watch for overhead power lines when handling the
sail and mast. NEVER rig, trailer or sail the boat near
overhead power lines. Mast contact with power lines
could be fatal.
Assembly Required | 15
hobie.com
Pull back on the mast
lock lever and pull the
mast up out of the boat
Mast Removal
Feed the furling line attached to the
mast collar throught the cleat
2
16 | Assembly Required
Making sure that there
are no twists in the line,
attach the mainsheet
hook to the grommet in
the sail.
1
Mainsheet Attachment
Sail Storage
To store the sail in the rolled
position, wrap the line around
the sail and hook the knot
into the hook sewn to the
sail. To take care of your sail,
always store it rolled up in the
provided storage bag.
Vantage CT | 17
hobie.com
Front Up/Down Adjust
Kickstand Activate Handle
Molded-In Kickstand Shelves
Front Up/Down “Key”
Recline Adjust
Seat Bottom Frame “Shoe”
BOA
®
Lumbar Adjust
Leash
Kickstand
Structural inserts for kickstand.
Does not require fasteners
Items not shown to scale
Anatomy
Vantage CT Video
18 | Vantage CT
Seat Installation
Line up the front of the
seat bottom frame over
key and slide the back
of the frame to the back
wall in the cockpit.
1
Put pressure on the front
of the seat mesh and
lift the back of the seat
bottom frame to set the
seat into the key.
2
Push the seatback frame
down once the seat frame
is fit into the key. Pull up
on front of seat to check
for proper installation.
3
Flip seat back up.
4
Vantage CT | 19
hobie.com
Warning: Failure to secure the seat
with the leash clip could result in
loss of seat during capsize event.
Locate leash buckle on
the seat bottom frame
and firewall behind the
seat.
5
Line up and plug in the
two parts of the buckle.
6
When the two parts are
clicked into place the
seat is secured to the
kayak.
7
Pinch to unlock.
8
20 | Vantage CT
Front Up/Down Adjustment
Pull lever out to
activate front up/down
adjustment.
1
Lean back into seatback
to raise the front up/down
adjustment. Use body
weight in seat bottom to
drop into a lower positon.
2
Release lever to lock
the desired position
of the front up/down
adjustment.
3
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
