Hobie Adventure Island User manual

Hobie

®

Mirage

®

Adventure Island Manual

In 1950, Hobie’s dream was born in his

parents’ garage when he decided to apply

his love of woodworking to the sport of

surfing. Dad backed out the Buick... Hobie

carved out his very first surfboard...

Hobie’s business of fun had begun.

Table of Contents | 5

hobiecat.com

Anatomy ....................................................................................................................6

Assembly ...................................................................................................................8

Vantage CT Seating ................................................................................................. 17

MirageDrive

®

...........................................................................................................24

On the Water ...........................................................................................................26

Lowrance

®

Ready Option ........................................................................................32

Storage and Transport ............................................................................................ 35

Maintenance and Care ............................................................................................ 38

Safety ......................................................................................................................42

Warranty ..................................................................................................................50

The Hobie Island Club is a place to meet other Hobie Mirage Adventure Island

and Hobie Mirage Tandem Island owners to share passions for the waterways and

oceans of our world. Hobie Dealers are organizing local Island Clubs worldwide.

The Hobie Island Club will assist in the introduction of Island owners to one

another where dreams of sailing to places unknown and countless adventures

can become a reality. Go to hobiecat.com or scan the QR code here to learn more

about joining a club near you.

6 | Anatomy

1. Hull

2. Vantage CT Seat

3. MirageDrive GT Turbo

4. Paddle and T-Handle

5. Lowrance-Ready Components

6. Cassette Plug

7. Akas (4)

8. Aka Carry Bag

9. Mast (2 piece)

10. Sail

11. Batten Set (3 pieces)

12. Small Parts (batten caps, spare sheer

pins, Loctite ® and steering riser (pg39)

6

4

5

3

Items not shown to scale

7

1

2

8

9

10

11

12

Anatomy | 7

hobiecat.com

Island Terminology

Battens

Battens are long fiberglass

rods that are inserted into the

sail to give it stiffness and help

maintain sail shape.

Amas

Amas are the outer

hulls that provide

stability under sail

power.

Centerboard

The centerboard is used to improve

your upwind performance by

preventing the boat from slipping

sideways in the water.

Roller Furler

The roller furler allows

the sail to be easily

rolled around the mast to

reduce sail size in high

winds and for storage.

Sail

The sail is a “square -top”

design that utilizes the current

trend in sail design for better

performance.

Telltales

Telltales are small ribbons

to help determine the

correct trim of the sail.

Akas

Akas are the aluminum bars that extend

away from the hull to support the amas.

Rudder

The rudder is the

rear blade that is

used to steer the

boat.

Mainsheet

The mainsheet is a rope

that connects to the sail

to control the trim of the

sail.

8 | Assembly Required

Slide the two halves of

the mast together

1

Insert the assembled

mast into the sail sleeve

2

Insert the webbing at the

top of the sail into the mast

cap

3

Feed the downhaul line

through the loop on the

mast collar. Pull tension on

the line to tighten the sail

onto the mast and cleat off

the line. Tie a knot off at

the end for extra security.

4

Mast/ Sail Assembly

Assembly Required | 9

hobiecat.com

Rotate the mast counterclockwise so that the sail rolls onto the mast per the

diagram below.

7

Slide the batten cap over the ends of the battens and lace the line through the

cap. Make sure to pull tension on the line and cleat it off to hold on the cap and

retain batten pressure into the pocket. Tie off the end of the line for extra batten

security.

6

Feed the battens into the

batten pockets (note they

are different lengths per the

different length pockets)

5

1. PULL

2. CLEAT

10 | Assembly Required

Rudder Installation

Place rudder over rudder

gudgeon and insert pin

1

Place the ring through

the hole in the end of the

rudder pin

2

Lift rudder up/down control

lines and make sure they

are running through the

middle of the rudder pin.

6

Assembly Required | 11

hobiecat.com

Slide the akas into

the deck mounted

crossbars until they

click into place.

1

Once the akas are inserted, pull out on them to make

sure they are locked in place.

2

Aka Installation

CLICK

To remove the akas,

depress both buttons at

the same time on the

deck mounted crossbar

and slide out the aka.

Aka Removal

12 | Assembly Required

Push in and hold the

diagonal crossbrace end

cap

1

Place end cap over ball

fitting on boat

2

Release end cap and check

to make sure it is locked

onto the boat

3

Diagonal Crossbrace Lock

Assembly Required | 13

hobiecat.com

Ama Installation

Slide the ama onto the aka

tubes

1

Stretch both Bungee®

cords over the buttons on

the corners of the akas.

2

14 | Assembly Required

Insert the mast

through the forward

crossbar bearing and

into the hull until it

goes all the way down

and locks

1

Mast Installation

Watch for overhead power lines when handling the

sail and mast. NEVER rig, trailer or sail the boat near

overhead power lines. Mast contact with power lines

could be fatal.

Assembly Required | 15

hobiecat.com

Pull back on the mast

lock lever and pull the

mast up out of the boat

Mast Removal

Feed the furling line attached to the

mast collar throught the cleat

2

16 | Assembly Required

Making sure that there

are no twists in the line,

attach the mainsheet

hook to the grommet in

the sail.

1

Mainsheet Attachment

Sail Storage

To store the sail in the rolled

position, wrap the line around

the sail and hook the knot

into the hook sewn to the

sail. To take care of your sail,

always store it rolled up in the

provided storage bag.

Vantage CT | 17

hobiecat.com

Front Up/Down Adjust

Kickstand Activate Handle

Molded-In Kickstand Shelves

Front Up/Down “Key”

Recline Adjust

Seat Bottom Frame “Shoe”

BOA

®

Lumbar Adjust

Leash

Kickstand

Items not shown to scale

Anatomy

Vantage CT Video

18 | Vantage CT

Seat Installation

Line up the front of the

seat bottom frame over

key and slide the back

of the frame to the back

wall in the cockpit.

1

Put pressure on the front

of the seat mesh and

lift the back of the seat

bottom frame to set the

seat into the key.

2

Push the seatback

frame down once the

seat frame is fit into the

key. Pull up on front of

seat to check for proper

installation.

3

Flip seat back up.

4

Vantage CT | 19

hobiecat.com

Warning: Failure to secure the seat

with the leash clip could result in

loss of seat during capsize event.

Locate leash buckle on

the seat bottom frame

and firewall behind the

seat.

5

Line up and plug in the

two parts of the buckle.

6

When the two parts are

clicked into place the

seat is secured to the

kayak.

7

Pinch to unlock.

8

20 | Vantage CT

Front Up/Down Adjustment

Pull lever out to

activate front up/down

adjustment.

1

Lean back into seatback

to raise the front up/

down adjustment. Use

body weight in seat

bottom to drop into a

lower positon.

2

Release lever to lock

the desired position

of the front up/down

adjustment.

3

Page is loading ...

Hobie Adventure Island User manual

Hobie Adventure Island User manual

Related papers

Other documents