Animal House 5403680 Operating instructions

The CHICK-INN™ ASSEMBLY INSTRUCTIONS

#5403680

47in H x 27.25in W x 72.5in D

119,4 x 70 x 184,2 cm

03-5403680 rev. 2018-07-30 PG.1

Please read through instructions completely prior to assembly.

TOOLS NEEDED: Phillips Screwdriver or power drill with phillips head bit

ASSEMBLY: Recommend 2 people. Approximate assembly time with 2 people: 90 Minutes

SITE PREPARATION: Ensure the area where you are placing your coop is a ﬂat level

surface, free from debris that can harm your pet.

SEPARATE AND INDENTIFY ALL PARTS parts listing on page 2

“EGGtastica”

Model #5403680

S = 2

Hen House

Roof Pieces

T = 1

Nest Box

Locking Lid

U = 1

Hen House

Peak Cap

X = 4

Anti-rot/Anti-dig

Ground Edging

Long pieces

P1 = 9 + 1

60mm

P2 = 24 + 1

40mm

P3 = 16 + 1

35mm

P4 = 15 + 1

25mm

P5 = 50 + 1

14mm

P6 = 1

Hen House

Sliding Door

Handle Kit

I = 1

Left Side

J = 1

Back

K = 1

Right Side

L = 1

Floor

M = 1

Divider

P = 1

Main Run

Gap Filler

Nest Box

N = 1

Back

O = 1

Side

Q = 1

Front (door)

R = 1

Top

Main Run

V = 1

Hen House

Slide out Tray

W = 2

Hen House

Roosts

Y = 2

Anti-rot/Anti-dig

Ground Edging

Short pieces

A = 1

Hen House Front

w/Door

B = 1

Hen House Back

w/Air Vents

C = 1

Hen House

Left Side

D = 1

Hen House

Right Side

E = 1

Entry/Exit

Ramp

F = 1

Lower Run

Front Piece

G = 1

Lower Run

Back Piece

H = 1

Lower Run

End Piece

Hen House

Lower Run

03-5403680 rev. 2018-07-30 PG.2

CAUTION! - SHARP EDGES!

03-5403680 rev. 2018-07-30 PG.3

STEP 1 - ATTACH GROUND EDGING (X, Y)

First determine the top/bottom and inside/outside of pieces

(F, G, H, N, O, Q)

F - has 2 holes on the OUTSIDE right and left sides, 1 hole on top

G - has 2 holes on the OUTSIDE right and left sides, 2 holes on top

H - has 2 holes on the right and left edges, 2 holes on bottom

N - has 3 holes on the OUTSIDE right edge, 3 holes on the OUTSIDE

left side, 2 holes on top

Q - from the OUTSIDE, the gate will be on the right

O - Top is slanted

Attach GROUND EDGING X to the bottoms of F, G, N & Q. Use (3) P5

screws along the bottom, (3) P5 screws along the inside edge.

Attach GROUND EDGING Y to the bottoms of H & O Use (3) P5 screws

along the bottom, (3) P5 screws along the inside edge.

Make sure the SHORT EDGE of the ﬂashing is on the INSIDE of

the wire panels, the LONG EDGE of the ﬂashing sticks out from

underneath to the outside. This prevents predators from digging

into the run, and provides an anchoring point.

Inside, Bottom

Outside, Bottom

X

or

Y

F,G,N,Q,H,O

P5 x 6

OUTSIDE

INSIDE

F

G

H

N

TOP

CAUTION! - EDGES ARE SHARP!

03-5403680 rev. 2018-07-30 PG.4

STEP 3B -

ATTACH RAMP (E) to (D)

Use (4) P5 screws

NOTE: line hinge up with the

bottom edge of coop door

STEP 4 - ASSEMBLE NEST BOX SIDES AND BOTTOM (I, K, L)

Use (4) P4 screws.

Attach the three-sided NEST BOX to the hen house BEFORE you attach the BACK PIECE (J)

Use (4) P3 screws. Now Attach the BACK PIECE (J) to the nest box. Use (7) P4 screws

J

P4 x 7

P4 x 4

I

K

L

STEP 2 - ASSEMBLE LOWER RUN (F,G,H,D)

Attach F and H use (2) P2 screws. NOTE: F attaches to the OUTSIDE edge of H

Attach G to OUTSIDE edge of H, use (2) P2 screws

Attach D to the INSIDE of F & G, use (4) P2 screws

STEP 3 - ASSEMBLE & ATTACH HEN HOUSE TO LOWER RUN (A, B, C)

Attach A to D use (2) P2 screws. NOTE: A attaches to the OUTSIDE of D.

Attach B to the OUTSIDE of D, use (2) P2 screws / Attach C to the INSIDE of A & B, use (4) P2 screws

Gently turn assembly on its side,

attach hen house to lower run

use (3) P1 screws

P2 x 2

A

D

P2 x 2

D

A

B

A

B

C

D

P2 x 2

P2 x 4

P2 x 2

P1 x 3

P5 x 4

P3 x 4

03-5403680 rev. 2018-07-30 PG. 5

STEP 5 - ATTACH MAIN RUN FRONT PIECE WITH GATE (Q)

Use (3) P1 Screws

Install sliding door HANDLE (P6). NOTE: slide handle through the hole in piece (Q)

before attaching the brackets. Use Four P5 screws.

P5 x 4

P6

Q

P1 x 3

STEP 6 - ATTACH REMAINDER OF MAIN WIRE RUN (N, O, P, R)

Attach N, Use (3) P1 Screws

Attach O to INSIDE edges of N and Q, Use (6) P2 screws

Attach P to top of O, use Two P2 screws

Attach SOLID TOP (R) Use Four P2 screws

P1 x 3

P2 x 6

P2 x 2

ADD DIVIDER (M)

Add 2 ROOSTS (W)

on the inside of the

house, there are 2 notches

Slide in TRAY V

M

W

V

P2 x 4

03-5403680 rev. 2018-07-30 PG.6

STEP 7 - ATTACH ASPHALT ROOF PIECES & CAP (S, T, U)

Attach NEST BOX LOCKING LID (T) Use (6) P5 screws

Attach (2) HEN HOUSE ROOF PIECES (S) Use (8) P3 screws

NOTE: The unﬁnished, slant cut edges are positioned at the peak. Push pieces towards

the back until they stop, this will align the holes in the roof with the holes in the coop.

Attach HEN HOUSE PEAK CAP (U) Use (4) P4 screws

S

T

U

P3 x 8

P5 x 6

P4 x 4

Animal House 5403680 Operating instructions

Animal House 5403680 Operating instructions

Other documents