Adjust-A-Gate AG60-DD Operating instructions

03-AG1-CONTRACTOR 2016-10-21

1

U.S. Patent # 5,716,041 & 5,868,382

ADJUSTABLE GATE FRAME ASSEMBLY INSTRUCTIONS

AG36, AG60

APPROXIMATE ASSEMBLY TIME: 1 Hour with 1 person

NOTE: Posts, 2x4’s and wood are NOT INCLUDED.

You must provide the wood to match your fence

application.

TOOLS NEEDED

Adjustable Wrench OR 9/16 Wrench Phillips Screwdriver

Wire Cutters 1/2 in. Spade / 5/16 Nut Driver / Power Drill

PARTS LIST

2x4’s Not Included

A

B

F

I

H

2x4’s Not Included

C

H

G

D

ORIGINAL SERIES

H

A

(2) 47 in. GATE FRAME SIDES

B (2) SPREADER BARS

1 in. x 1 in. x 36 in. (for AG36)

1 in. x 1 in. x 48 in. (for AG60)

C (1) TRUSS CABLE KIT

D (2) GATE FRAME HINGES

with bolt and nut

E (2) POST HINGES

F (1) GATE LATCH KIT

G (24) 1” ROUNDHEAD WOOD SCREWS

for 2x4 clips

H (10) 2” FLATHEAD WOOD SCREWS

for spreader bars

I (4) 1” HEX HEAD SELF-TAPPING SCREWS

for striker bar

J (12) 2” ROUNDHEAD WOOD SCREWS

for post hinges

K (6) 1 ½” ROUNDHEAD WOOD SCREWS

for latch catch

L (4) 3/4” HEX HEAD SELF-TAPPING SCREWS

for double drive latch

03-AG1-CONTRACTOR 2016-10-21

2

• Familiarize yourself with the gate hardware frames and instructions.

• Note: concave side of spreader bars faces down.

• This frame is designed to open INWARD (into your fenced area), if your application calls for an OUTWARD opening you

can adjust the placement of the POST HINGES to the opposite side of the post. Additional modiﬁcations may be needed

for outward swinging gates.

• For double drive gates openings use two gate kits. The gates will assemble the same way, just reversed. For the

latch installation on a double-drive gate, ﬁrst attach the STRIKER BAR, bring both gates together and line up the

LATCH CATCH with the striker bar for correct alignment to gate frame and attach. Suggested space between double

gates is 1 inch.

• For double-drive gates drop rod kits are highly recommended (sold separately).

• As a Security precaution - Installing HINGE (E) with the top bolt facing down and the bottom bolt facing up will prevent

the potential theft by locking the frame into itself.

• Make sure all 4x4’s posts and 2x4’s rails are straight (bowing or crooked 4x4 & 2x4’s may make the adjust-a-gate out

of alignment)

• If cutting the spreader bars spray all cut ends with a Rust Oleum® type product to prevent rusting.

GETTING READY TO ASSEMBLE YOUR GATE KIT

STEP 1: POST HINGE (E) INSTALLATION

A) Locate the CENTER POINT (top to bottom) on your POST.

B) Measure up 16” and down 16” to ﬁnd the CENTER

POINT for each POST HINGE BRACKET (E).

C) Position POST HINGE BRACKETS so J-BOLTS point toward

the center point and the hinge plates are on the inside

gate swinging side of the post. Attach brackets using 2”

WOOD SCREWS (J)

Note: for best results this Adjust-A-Gate is designed to open

inward but can be modifed to open outward by placing the

hinges on the opposite side of the post

STEP 2: GATE HINGE (D) and FRAME (A) INSTALLATION

A) Loosely attach the FRAME HINGES (D) to the HINGE SIDE of

the GATE FRAME (A) - remember that the pre-drilled hole

for the truss cable is located at top inside of this frame

piece.

Slide the BOTTOM FRAME HINGE (D) into position onto the

BOTTOM POST HINGE (E), tighten bolt.

Slide the TOP FRAME HINGE (D) into position onto the

TOP POST HINGE (E), tighten bolt.

B) Insert the SPREADER BARS (B) into slip member on the

gate frame as shown.

B

E

J

D

B

16”

03-AG1-CONTRACTOR 2016-10-21

3

STEP 2C: LATCH SIDE OF FRAME (A) INSTALLATION

Carefully add the LATCH SIDE OF THE FRAME (A)

Now, carefully (at this point the frame is still loose) extend

the gate frame to within 1 inch of the post where the latch

will be attached.

Now measure the distance between the plates where the

2x4’s will attach (top and bottom of frame), cut 2x4’s and

attach using 1 INCH ROUNDHEAD WOOD SCREWS (G) for the

plates, and 2 INCH FLATHEAD WOOD SCREWS (H) for the

spreader bars.

NOTE: Depending on the width of your gate, you may not

need all of the 2 inch wood screws, it is not necessary to have

a screw in every hole. Because it is an adjustable frame, not

all the pre-drilled holes on the spreader bars and vertical

frame sides will line up.

STEP 3: TRUSS CABLE and GATE LATCH INSTALLATION

Be sure to loosen the TURNBUCKLE to its widest opening

prior to assembly.

Assemble TRUSS CABLE as shown.

Slide the “S” HOOK of the TRUSS CABLE KIT (C) into the

hole at the lower corner of the latch side of the gate frame.

Hook the TURNBUCKLE into the hole at the opposite top

corner on the hinge side of the frame.

Form a loop on the loose end of the cable, thread through

the CABLE CLAMP, slip that loop onto the “S” HOOK and

pull cable tight, secure with clamp, cut off any excess.

Attach STRIKER BAR from the Gate Latch Kit (F) to the

inside gate frame at the desired height use the 4 HEX HEAD

SELF-TAPPING SCREWS (I) . Align the LATCH with the Striker

Bar and attach to post using 1.5 INCH ROUNDHEAD WOOD

SCREWS (K).

By adjusting the TURNBUCKLE you can ﬁne tune the gate

latch to give a perfect ﬁt.

1”

2x4’s Not Included

F

C

I K

G H AG

G H G

03-AG1-CONTRACTOR 2016-10-21

4

STEP 4: ATTACHING YOUR BOARDS

TIP: To hide the gap on the HINGE SIDE of the gate, you may

overlap your fence board to cover this gap. APPLICABLE TO

INWARD SWINGING GATES ONLY

TIP: It is recommended that your gate boards be cut 2”

shorter than the fence boards to allow the top of your

gate to be even with the fence and allow clearance under

the gate.

Now you can attach the rest of your boards onto the 2x4’s

on the gate using nails or screws.

By adjusting the tunbuckle on the truss cable you can ﬁne

tune the gate.

LATCH CATCH ASSEMBLY FOR DOUBLE DRIVE GATES

I

L

Page is loading ...

03-AG1-CONTRACTOR 2016-10-21

17

Brevetto US # 5,716,041 & 5,868,382

ISTRUZIONI DI ASSEMBLAGGIO DEL TELAIO PER CANCELLO REGOLABILE

AG36 / AG60

TEMPO APPROSSIMATIVO RICHIESTO: 1 ora per 1 persona

NOTA: Pilastri, assi 3.8x8.9cm e legno NON INCLUSI.

Le parti in legno coordinate a quelle della staccionata

sono a vostro carico.

ATTREZZI RICHIESTI

Chiave regolabile O chiave da 14mm Cacciavite a stella

Tronchese Punta a lancia da 1.25cm/Chiave a brugola da 8mm /Trapano

LISTA PARTI

Assi 3.8x8.9cm cm non incluse

A

B

F

I

H

G

H

Assi 3.8x8.9 cm non incluse

C

H

D

A (2) LATI TELAIO CANCELLO da 1.2m

B (2) BARRE DISTANZIATRICI

2.5 x 2.5 x 92 cm. (for AG36)

2.5 x 2.5 x 122cm. (for AG60)

C (1) KIT CAVI TENDITORI

D (2) CERNIERE TELAIO CANCELLO

Con viti e dadi

E (2) CERNIERE PILASTRO

F (1) KIT CHIAVISTELLO

G (24) VITI PER LEGNO A TESTA TONDA 2.5 CM

Per ganci

H (10) VITI PER LEGNO A TESTA PIATTA 5 CM

Per barre distanziatrici

I (4) 2,5cm VITI AUTO FILETTANTI A TESTA ESAGONALE

per barra di aggancio

J (12) VITI PER LEGNO A TESTA TONDA 5 CM

per le cerniere del

pilastro

K (6) VITI PER LEGNO A TESTA PIATTA 3.8 CM

per il gancio del

chiavistello

L (4) 2cm VITI AUTO FILETTANTI A TESTA ESAGONALE

per cancelli a doppia ante

I

H

Page is loading ...

03-AG1-CONTRACTOR 2016-10-21

21

Patente de Estados Unidos # 5,716,041 & 5,868,382

INSTRUCCIONES DE MONTAJE PARA EL MARCO DE UNA PUERTA AJUSTABLE

AG36 / AG60

TIEMPO APROXIMADO DE MONTAJE: 1 hora con 1 persona

NOTA: Postes, 3.8x8.9cm y madera NO ESTÁN INCLUIDOS.

Usted debe proporcionar la madera que coincida con la

aplicación de su cerca.

HERRAMIENTAS NECESARIAS

Llave ajustable O Llave 14mm Destornillador tipo Phillips

Cortacables Pala de 1.2cm / Llave de tuerca 8mm / Taladro

LISTA DE PARTES

A

B

F

I

H

G

H

C

H

D

3.8x8.9cm No Incluidos

E

H

A (2) MARCOS LATERALES DE LA PUERTA

DE 1.2cm

B (2) BARRAS DE SEPARACIÓN

2.5 x 2.5 x 92 cm. (para AG36)

2.5 x 2.5 x 122cm. (para AG60)

C (1) KIT DE CABLE DE

CELOSÍA

D (2) BISAGRAS DE MARCO DE PUERTA

con perno y tuerca

E (2) BISAGRAS PARA

POSTE

F (1) KIT DE CERROJO

PARA PUERTA

G (24) TORNILLOS DE 2.5cm CON CABEZA

REDONDEADA PARA MADERA

para clips

H (10) TORNILLOS DE CABEZA PLANA

DE 5cm PARA MADERA

para las barras separadoras

I (4) TORNILLOS CON CABEZA

HEXAGONAL de 2.5cm AUTORROSCANTES

para la barra golpeadora

J (12) TORNILOS DE CABEZA REDONDA

PARA MADERA 5cm

para las bisagras de los postes

K (6) 3.8cm TORNILLOS DE CABEZA REDONDA

MADERA

para el cerrojo de la puerta

L (4) TORNILLOS CON CABEZA

HEXAGONAL de 2.5cm AUTORROSCANTES

para puerta de accionamiento doble

Page is loading ...

Adjust-A-Gate AG60-DD Operating instructions

Adjust-A-Gate AG60-DD Operating instructions

in other languages

Related papers

Other documents