INSTALLATION OF THE FAUCET
!
1 New Faucet Preparation
Completely shut off the water supply.
Remove the old faucet by disconnecting it
from the water supply tubes under the
sink. Clean the sink’s top surface in
preparation for installation of the new
faucet.
2 Install Faucet and Basket
Strainer on Sink
Position the faucet onto the sink’s top. (A).
Hand tighten locknuts. (B). If your sink is
uneven, and the faucet does not sit flush,
use silicone under the base. (R). Pass the
hose through the faucet, and adjust the
position of the faucet so that the hose does
not rub against the edge of the sink hole.
Attach the hose onto Check valve (M) and
Wand assembly (P), and tighten securely.
(S). Attach zinc weight to hose assembly
as shown.
3 Install Faucet Under Sink
Screw the provided locknuts upward from
under the sink onto faucet connectors
using your hands only. Tighten the nuts
alternating until they are nearly flush with
the underside of the sink top. Then, align
the faucet as desired. While maintaining
set alignment, tighten down the locknuts
to lock faucet into place. Attach water
supply lines to faucet by tightening nuts A
and B. Do not overtighten.
4 Connect to Water Supply
Last step is to connect to the water supply.
(G). Turn the faucet handles all the way on.
(H). Next turn on both the hot and cold
water supply and allow both the hot and
cold water to run for at least one minute
each. While the water is running, check for
leaks around and under the sink.
MAINTENANCE AND CLEANING
Cleaning Tips: The finish on your product
is designed to retain its beautiful sheen
for years. To maintain the original look of
the finish, a little care and caution should
be used. We recommend the use of mild
soap and water to clean the product.
THE USE OF ABRASIVE CLEANERS MAY
SCRATCH THE FINISH OR CAUSE
OTHER DAMAGE.
RECOMMENDED TOOLS AND
MATERIALS
¨ Adjustable Wrench
¨ Plumbers Tape (Thread Seal
Tape)
¨ Phillips Screw Driver
BEFORE YOU BEGIN
There are a variety of things to do before
installing any new plumbing system into
your home or residence. Before you begin
work make sure you:
¨ Shut off the main water supply
¨ Cover your drain to prevent
loss of parts
¨ Observed any local plumbing
codes
¨ Inspect fixture for damage -
Replace as necessary
* Dura Faucet reserves the right to make
any revisions in the design of products
without notice.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
1. Stainless Steel Screw
2. ABS(BN) Handle
3. POM Ring
4. ABS(BN) Nut
5. POM/Rubber/Stainless Steel Cartridge-Hot
6. ABS(BN) Cylinder
7. POM/Brass/ABS/Rubber/Stainless/TPR Spray
Gun Group
8. Rubber O-Ring
9. Rubber O-Ring
10. ABS(BN) Escutcheon
11. Rubber O-Ring
12. Rubber Washers (2)
13. Stainless Steel Springs
14. POM/Rubber Body
15. POM Base
16. Stainless Steel Spring
17. POM Heart Son
18. Rubber O-Ring
19. POM Cover
20. Rubber O-Ring
21. PP Base Plate
22. Stainless Steel Screws (2)
23. Pb Up Pb Chunk
24. PB Down Pb Chunk
25. ABS/Brass/PVC Hose Group
26. Stainless Steel Screws (2)
27. Rubber Washers (2)
28. ABS Mounting Nuts (2)
29. Rubber Washers (2)
30. ABS Coupling Nuts (2)