2. Toro
  3. Light Kit, Proline Commercial Walk-Behind Mower

Toro Light Kit, Proline Commercial Walk-Behind Mower Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Light Kit, Proline Commercial Walk-Behind Mower Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3436-365RevA
LightKit
ProlineCommercialWalk-BehindMowerwith60inFloatingCutting
Unit
ModelNo.139-5595
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparethemachine.
LEDlight2
Lightbracket1
Frictionwasher2
Carriagebolt(5/16x7/8inch)
2
Flangenut(5/16inch)
2
Lightclamp2
2
Locknut(1/4inch)
4
Installthelights.
Wireharness1
Cableties
6
3
Toggleswitch1
Routethewireharness.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface,disengage
thePTO,andengagetheparkingbrake.
2.Shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operatingposition.
3.Disconnectthebattery;refertoyourOperator’s
Manual.
2
InstallingtheLights
Partsneededforthisprocedure:
2LEDlight
1Lightbracket
2Frictionwasher
2
Carriagebolt(5/16x7/8inch)
2
Flangenut(5/16inch)
2Lightclamp
4
Locknut(1/4inch)
©2019—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3436-365*A
Procedure
1.Securethe2LEDlightstothelightbracket
using2carriagebolts(5/16x7/8inch),2friction
washers,and2angenuts(5/16inch)asshown
inFigure1.
g307082
Figure1
1.Carriagebolt(5/16x7/8
inch)
4.Lightbracket
2.LEDlight
5.Flangenut(5/16inch)
3.Frictionwasher
2.Securethelightassemblytothemuferguard
using2lightclampsand4locknuts(1/4inch)
asshowninFigure2.
g307081
Figure2
1.Lightclamp3.Lightassembly
2.Locknut(1/4inch)4.Muferguard
2
3
RoutingtheWireHarness
Partsneededforthisprocedure:
1Wireharness
6
Cableties
1Toggleswitch
Procedure
1.Plugthe2connectorsatthefrontofthemachine
intotheLEDlights(Figure3).
g307414
Figure3
1.Lightconnector2.Harnessconnector
2.Securethewireharnesstothelightbracket
usingthe2push-mountfastenersonthewire
harness(Figure4).
g307415
Figure4
1.Push-mountfastener
2.Lightbracket
3
3.Routethewireharnessalongtherightsideof
themachineasshowninFigure5.
4.Securethewireharnesstothemachineusing
thecableties(Figure5).
g307416
Figure5
4
5.Plugtheconnectorintothetoggle-switch
connector(Figure6).
g307412
Figure6
1.Harnessconnector2.Toggle-switchconnector
6.Drillahole(12mmor1/2inch)infrontofthe
hourmeterforthetoggleswitch(Figure7).
g307413
Figure7
1.Measure12.7mm(1/2
inch)fromthehourmeter
todrillthehole.
2.Drillahole(12mmor1/2
inch)here.
7.Fromthetopofthethreadsonthetoggleswitch,
setthedepthofthebottomhexnutat7.9mm
(5/16inch)asshowninFigure8.
g307440
Figure8
1.7.9mm(5/16inch)
5
8.Securethetoggleswitchintheopeningusing
the2hexnutsand1lockwasher(Figure9).
Note:Donotusethekey-tabwasher.
g307441
Figure9
1.Hexnut3.Toggleswitch
2.Lockwasher
9.Connectthebattery;refertoyourOperator’s
Manual.
6
Notes:
/