6
614-06821-00
1. Operating conditions
• This product is an Uninterruptible Power Supply (UPS) for computers and their peripherals, television sets, stereo
systems and video recorders... It must not be used to supply other electrical equipment (lighting, heating, household
appliances, etc.).
2. UPS connections
• Connect the UPS
1
to the AC-power system via a wall outlet with an earth connector, using the input cord of your
computer(seegureA).
• Plug critical equipment (computer, monitor, modem, etc.) into the outlets
9
providing battery backup power and surge
protection(seegureB),takingcarenottoexceedtheratedcurrentindicatedinamperes.
• Otherdevices(printer,scanner,fax,etc.)canbeconnecttothelteredoutlets
8
that provide surge protection
(seegureB).Thelteredoutletsarenotbackedupbybatterypowerintheeventofapoweroutage.
• Optional Internet modem / Network connection:
A modem or Ethernet data line can be protected against surges by connecting it via the UPS. Connect the existing device
cable between the wall outlet and the UPS, and use a similar cable between the UPSandthedevice,asindicatedingure
C (cable not supplied).
• Optional USB connection:
The UPS device can be connected to the computer using the USB cable
5
supplied.
EatonUPSCompanionsoftwareisdownloadablefrompowerquality.eaton.com(seegureB).
Register for the warranty on powerquality.eaton.com.
3. Operation
• Battery charge: The UPS charges the battery as soon as it is connected to the AC outlet, whether button
12
is pressed
ornot.Whenusedforthersttime,thebatterywillonlyprovideitsmaximumautonomyafterithasbeenchargedfor
8 hours. It is recommended that the UPS be permanently connected to the AC power supply to ensure the best possible
autonomy.
• Switching-on the UPS: press button
12
for about 1 second.
• Filtered outlets
8
without battery backup: Equipment connected to these outlets is supplied as soon as the input AC
cord is plugged in. They are not affected by button
12
.
• Battery backup outlets
9
: Equipment connected to these outlets is supplied as soon as button
12
turns green
(seegureD).TheseoutletscanbeturnedoneveniftheUPS is not connected to AC power (button
12
ashes).
• AC-power disturbance: If AC power is disturbed or fails, the UPS continues to operate on battery power. Button
12
ashes
green. In normal mode, the audio alarm beeps every ten seconds, then every three seconds when the end of battery
backup time is near. In silent mode (see the section on settings), the audio alarm simply beeps once when the UPS
transfers to battery power.
• If the power outage lasts longer than the battery backup time, the UPS shuts down and automatically restarts when
power is restored. Following a complete discharge, a few hours are required to recharge the battery back to full backup
time.
• To save battery power, it is possible to press button
12
to cut the supply of power to the devices connected to the battery
backup outlets.
• Surge protection:Alloutlets,whetherbackeduporsimplyltered,includesurgeprotection,whateverthepositionof
button
12
.
• Shutdown of the battery backup outlets
9
: Press button
12
for more than two seconds.
Troubleshooting (For further information, visit the www.powerquality.eaton.com site or contact after-sales support.)
Problem Diagnostic Solution
1
• The battery backup outlets
9
are not
supplied with power.
• Button
12
is not lighted on. • Press button
12
and check that it turns
green.
2 • The connected devices are not
supplied when AC power fails.
• The devices are not connected to the
battery backup outlets
9
.
• Connect the devices to the battery
backup outlets
9
.
3 • AC power is available, but the UPS
operates on battery power.
• Circuit breaker
13
, located under the
UPS, has been tripped by an overload
on the UPS output.
• Disconnect excess equipment and
reset the circuit breaker
13
by pressing
the corresponding button.
4
• Green button
12
and red LED
11
are
on and audio alarm beeps every 2
seconds.
• The UPS battery backup outlets
9
are overloaded.
• Disconnect excess equipment
connected to the battery backup outlets
9
.
5
• Red LED
11
is on and the audio alarm
beeps every continuously.
• A fault has occurred on the UPS. The
battery backup outlets
9
are no longer
supplied.
• Call after-sales support.
8
: Filtered outlets.
9
: Battery backup outlets.
11
: LED ON indicate a UPS fault.
12
: ON/OFF button for the battery backup
outlets.
13
: Protection (circuit breaker).
1
2
3
4
5
6
7
8
Eaton Ellipse ECO 1600VA User manual
Eaton 3S 700 IEC User manual